推进石化销售企业质量管理创新发展

对照IS0 9001质量管理体系标推的要求，结合石化销售企业质量管理工作中存在的主要问题，提出质量管理工作创新的建议。     

The influence of silicon on carbon redistribution in steel weldments

Carbon redistribution was measured in ST1/ST2 Fe-2.5Si-0.8C/Fe-0.32Si-0.49C steel weldments in the temperature range 500–1000 °C. At the temperatures where austenite exists, carbon diffuses from ST1 into ST2; when ferrite is present, the diffusion flow reverses from ST2 into ST1. This effect is attributed to the degree of the silicon influence on the graphite precipitation and carbon activity in ST1 and ST2 steels. The opposite signs of the activity gradients in austenite and ferrite cause the reversal of the carbon diffusion when the annealing temperature is changed from the austenite to the ferrite temperature region. The carbon diffusion coefficients D_C and the thermodynamic interaction coefficients ε_C^Si in austenite have been assessed from the experimental data for ST1 and ST2 steels.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

乙炔黑吸附聚合制导电聚苯胺

用乙炔黑吸附化学聚合新工艺制备导电聚苯胺，可保持电导率不变，但转化率和堆密度提高，并明显改善了聚苯胺的颗粒形态和制膜加工性，使由其制备的聚苯胺复合正极膜和固体聚苯胺锂蓄电池的电化学性能得以改进。     

Policies to reduce energy use and carbon emissions in the UK

The UK differs from may other industrialized nations in that its carbon dioxide (CO₂) emissions from energy use have declined in recent years despite relatively rapid economic growth. In all sectors but transport, substantial reductions have already occurred in the level of carbon emissions per unit of GDP output. At the same time, a number of official and unofficial studies have pointed out that the UK has one of the largest remaining potentials amongst comparable industrialized countries for achieving further CO₂ reductions through the implementation of cost-effective energy efficiency and fuel switching measures. This paper discusses past and present patterns of energy use and carbons emissions in the UK. The analysis then examines historical trends in UK energy policy and presents policy options for further reducing the UK's energy-use and carbon emissions in the future.     

二氧化碳对油井水泥石的腐蚀及其防护措施

在湿环境下,油气构造中富含的CO_2对水泥石产生碳化腐蚀,碳化结果使水泥石渗透率变大、抗压强度减小,诱发流体窜流、塑性地层井壁垮塌等事故,造成巨大的经济损失。介绍了在不同温度下的水泥水化产物及其碳化产物。从化学角度分析了CO_2在不同温度下对油井水泥环碳化腐蚀的机理、影响因素及防护措施。在低于110℃的温室下,CO_2的腐蚀速度受扩散控制,其影响因素包括水泥浆密度和水泥石渗透率及水泥石孔隙液中Ca(OH)_2的含量,在水泥中掺加活性硅灰或提高水泥浆密度可预防碳化腐蚀。在大于110℃的高温下,碳化腐蚀速度受水泥水化产物中Ca(OH)_2含量和水泥石碳化后渗透率大小的影响。正确的防腐工艺是在水泥石中加入10％—15％的石英砂,或者在纯水泥中加3％—8％的膨润土。     

采用活性非均匀分布催化剂中变反应器的模拟计算

模拟计算表明:采用活性趋于表层的分布,可以较明显地提高国产中温变换催化剂的内表面利用率,有效地节省催化剂用量,而对“热点”温度没有多大影响。     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

镨掺杂分布对1.3μm光纤放大器特性影响

对掺氟化镨玻璃光纤放大器的小信号增益，用广义的高斯近似公式可获得精确的分析表达。文中研究了限制光纤芯层中央部分的镨掺杂对光纤放大器特性的影响，结果发现限制镨掺杂分布能改进光纤放大器的工作效率，且截止波长比芯层全部均匀掺镨的光纤更长。     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.