Efficient dye-sensitized solar cells based on CNTs and Zr-doped TiO2 nanoparticles

The light scattering, harvesting and adsorption effects in dye-sensitized solar cells (DSSCs) are studied by preparation of coated carbon nanotubes (CNTs) with TiO₂ and Zr-doped TiO₂ nanoparticles in the forms of mono- and double-layer cells. X-ray diffraction (XRD) analysis reveals that the phase composition of Zr-doped TiO₂ electrode is a mixture of anatase and rutile phases with major rutile content, whereas it is the same mixture with major anatase content for coated CNTs with TiO₂. Furthermore, the average crystallite size of Zr-doped TiO₂ electrode is slightly decreased with Zr introduction. Field emission scanning electron microscope (FE-SEM) images show that the porosity of Zr-doped TiO₂ electrodes is higher than that of undoped electrode, enhancing dye adsorption. UV–visible spectroscopy analysis reveals that the absorption onset of Zr-doped TiO₂ electrodes is slightly shifted to longer wavelength (the red-shift) in comparison with that of undoped TiO₂ electrode. Moreover, the band gap energy of TiO₂ nanoparticles is decreased by Zr introduction, enhancing light absorption. It is found that electron injection of monolayer TiO₂ electrode is improved by introduction of 0.025 mol% Zr, resulted in enhancement of its power conversion efficiency (PCE) up to 6.81% compared with 6.17% for pure TiO₂ electrode. Moreover, electron transport and light scattering are enhanced by incorporation of 0.025 wt% coated CNTs with TiO₂ in the over-layer of double layer electrode. Therefore, double layer solar cell composed of 0.025 mol% Zr-doped TiO₂ nanoparticles as the under-layer and mixtures of these nanoparticles and 0.025 wt% coated CNTs with TiO₂ as the over-layer shows the highest PCE of 8.19%.     

The significant promotion of g-C3N4 on Pt/CNS catalyst for the electrocatalytic oxidation of methanol

This article reported a series of g–C₃N₄–CNS (g-C₃N₄ and carbon nanosheets) composite carriers formed by the hydrothermal method, and then the ethylene glycol reduction method was used to anchor Pt nanoparticles on the g–C₃N₄–CNS carrier to form the Pt/g–C₃N₄–CNS catalysts. The electrochemical test for the electrocatalytic oxidation of methanol (MOR) shown that the Pt/20%g–C₃N₄–CNS catalyst has the best catalytic performance and stability. These Pt/g–C₃N₄–CNS catalysts were analyzed by TEM, XRD, XPS, and BET characterization. It is discovered that the amount of g-C₃N₄ greatly influenced the structure and chemical properties of Pt/CNS precursor. As the content of g-C₃N₄ increases, the content of pyridine nitrogen and pyrrole nitrogen also increases, and N species can enhance the interaction between Pt nanoparticles and CNS, promote Pt dispersion, and increase the specific surface area of the catalyst. Similarly, an excessive addition of g-C₃N₄ will cause a sharp decline in the conductivity of the catalyst, and then led to the decline of MOR activity.     

Strength of pure alumina ceramics above 1 GPa

Up to now, commercially available alumina ceramics were claimed to have strength between 400 and 550 MPa. However, our study shows strength ~ 2 times higher for commercially available alumina than commonly believed. The average and characteristic strength, measured on 31 pure alumina ceramic discs by ball on three balls (B3B) test, were 1205 ± 93 MPa and 1257 MPa, respectively, with a Weibull modulus of m = 11.8. Tested specimens were in form of discs with a diameter of 5 mm and thickness 0.5 mm. The grain size distribution of the alumina is bimodal with an average grain size of ~ 850 nm measured at the surface. The fracture reveals a mixed transgranular / intergranular failure mode. To avoid incorporation of additional flaws, the discs were tested as sintered. The characteristic flexural strength measured in B3B was recalculated according to Weibull theory for standard 4-point bending bars of size 3 × 4 × 45 mm as bend 856 MPa. The measured strength of nearly 900 MPa shows the potential of strength for high purity alumina ceramics.     

Experimental study to assess the effect of carbon nanotube addition on the through-thickness electrical conductivity of CFRP laminates for aircraft applications

The present paper tests experimentally the through-thickness electrical conductivity of carbon fiber-reinforced polymer (CFRP) composites laminates for aircraft applications. Two types of samples were prepared: Type A samples with carbon nanotubes (CNTs) and Type B samples without CNTs. During the electrical experiments, electrical currents of several mA were injected through the specimens. Electrical resistance was monitored simultaneously in order to deduce the changes in the through-the-thickness electrical conductivity caused by the addition of CNTs. Improvement of electrical conduction by two orders of magnitude was achieved through the addition of 1 wt% carbon nanotubes as compared to classic CFRP without CNTs. For moisture saturated samples, the influence of moisture absorption on such measures was found to be negligible.     

Tough salami-inspired Cf/ZrB2 UHTCMCs produced by electrophoretic deposition

One of the biggest challenges of the materials science is the mutual exclusion of strength and toughness. This issue was minimized by mimicking the natural structural materials. To date, few efforts were done regarding materials that should be used in harsh environments. In this work we present novel continuous carbon fiber reinforced ultra-high-temperature ceramic matrix composites (UHTCMCs) for aerospace featuring optimized fiber/matrix interfaces and fibers distribution. The microstructures – produced by electrophoretic deposition of ZrB₂ on unidirectional carbon fibers followed by ZrB₂ infiltration and hot pressing – show a maximum flexural strength and fracture toughness of 330 MPa and 14 MPa m^1/2, respectively. Fracture surfaces are investigated to understand the mechanisms that affect strength and toughness. The EPD technique allows the achievement of a peculiar salami-inspired architecture alternating strong and weak interfaces.     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

黄浦江下游吴淞口站低潮位重现期研究

黄浦江为感潮河流,低潮位重现期的确定对黄浦江航道的设计具有重要意义。为了准确估计黄浦江低潮位的重现期,以黄浦江下游吴淞口站年最低潮位序列为例,在对样本进行三性审查的基础上,分别采用传统的数理统计方法和时变矩方法进行水文频率分析。结果表明:吴淞口站年最低潮位序列在1996年发生了变异;还现修正后的序列服从位置参数线性时变的GEV模型,低潮位存在缓慢的上升趋势;一致性条件下百年一遇低潮位约为0.261 m,在非一致性条件下其重现期增大为150 a。非一致性条件下的重现期增大说明黄浦江现有的航道设计标准偏安全,航道通航保证率提高。     

Neutral axis depth and moment redistribution in FRP and steel reinforced concrete continuous beams

The neutral axis depth is considered the best parameter for quantifying the moment redistribution in continuous concrete beams, as exemplified in various design codes worldwide. It is therefore important to well understand the variation of neutral axis depth against moment redistribution. This paper describes a theoretical investigation into the neutral axis depth and moment redistribution in concrete beams reinforced with fibre reinforced polymer (FRP) and steel bars. A finite element model has been developed. The model predictions are in favourable agreement with experimental results. Three types of reinforcement are considered, namely, glass fibre, carbon fibre and steel. Various levels of reinforcement ratio are used for a parametric evaluation. The results indicate that FRP reinforced concrete continuous beams exhibit significantly different response characteristics regarding the moment redistribution and variation of neutral axis depth from those of steel reinforced ones. In addition, it is found that the code recommendations are generally unsafe for calculating the permissible moment redistribution in FRP reinforced concrete beams, but the neglect of redistribution in such beams may be overconservative.     

Combination of nuclear magnetic resonance spectroscopy and nonlinear methods to analyze the copolymerization of phosphonic acid derivatives

We demonstrate in this study that the combination of modern inline monitoring methods [here: inline nuclear magnetic resonance (NMR)] with simulations gains more exact and profound kinetic results than previously used methods like linearization without that combination. The ¹H-NMR spectroscopic data (more than 100 data points) are used to construct the copolymerization diagram. The reactivity ratios are obtained applying the van Herks nonlinear least square method. The examination of the radical copolymerization of 2-hydroxyethyl methacrylate (HEMA) with (2-{[2-(ethoxycarbonyl)prop-2-en-1-yl]oxy}ethyl) phosphonic acid (ECPPA) as important adhesive monomer used in dentistry yields reactivity ratios of r_HEMA = 1.83; r_ECPPA = 0.42. The copolymerization diagram reflects nonideal, non-azeotropic copolymerization. The sequence distribution of the obtained by Monte Carlo simulation indicates the generation of statistical copolymers. As an important finding, it is demonstrated that the repeating units responsible for etching and adhesion are arranged over the whole polymer chain, which is necessary to achieve proper functionality. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48256.     

Modelling of black carbon statistical distribution and return periods of extreme concentrations

Eight datasets of 1-h black carbon (BC) concentrations measured in Warsaw agglomeration (Poland), at urban background and sub-urban sites, and in Racibórz, a small town in Upper Silesia district (regional background site) were analyzed to evaluate BC levels, daily profiles and statistical distributions of concentrations in Central-Eastern European region. The observed mean levels ranged from 1483 ng m⁻³ in suburban site during summer to 3358 ng m⁻³ in regional background site in winter. Observed diurnal patterns were bimodal in the locations dominated by traffic emissions, but unimodal, with elevated evening peak in individually heated residential area. Three theoretical frequency distributions were applied to fit analyzed datasets separately. The lognormal distribution was the most appropriate to represent the middle-range values, while the high concentrations were satisfactorily predicted by the type I two-parameter exponential distribution which was used to estimate the return periods of extreme concentrations for winter months.