多层水平气流带式干燥机的数学模型

根据干燥传质传热学原理和干燥动力学特性，建立了水平气流带式干燥机干燥过程的数学模型。该模型可以预测干燥机合理的通风道高度、带翻转最佳时间和热风风速等。为优化多层带式干燥机的结构或设计新的水平气流带式干燥机提供了理论依据。     

Process conditions affect pigment quality and yield in extracts of purple sunflower hulls

Extract of purple sunflower hulls is a potential red food colorant; however, suitable process conditions must still be identified. Selected process variables were studied using bench-scale units to prepare, clarify, concentrate and spray dry extracts. Concentration by evaporation at 32°C and addition of maltodextrin to 15% (wt/dry wt) prior to drying largely eliminated pigment degradation during those steps. Relative to water extracts, extracts prepared with 5 to 15% ethanol in water generally yielded more pigment with similar levels of degradation and loss during subsequent processing. Use of 5% ethanol/2% citric acid reduced yield by about half relative to water, but gave a powder with a lower degradation index and wetting time. Percentage recovery of pigment during concentration and drying was not greatly affected by solvent type or extraction temperature.     

Carbon Aerogels as Electrode Material in Supercapacitors

Due to their large specific surface area and their high electrical conductivity carbon aerogels are promising materials for electrodes in electrochemical double-layer capacitors (supercapacitor). The carbon aerogels were made via pyrolysis of resorcinol formaldehyde aerogels. The latter were prepared by supercritical and subcritical drying as well. The important findings of our investigation were, that the highest capacities of 46 F/cm³ were measured for samples with a density of about 800 kg/m³ pyrolyzed at 800°C. Also it was shown that RF-gels with molar resorcinol/catalyst ratios 1000 or higher can be dried subcritically without cracking or significant shrinkage. Carbon aerogels derived from these RF-aerogels have a small mesopore surface area, however an especially large micropore area. They provide electrical capacities which are most suitable for their use in supercapacitors.     

Reply to the Comment by K. Jorgensen et al. to “Analysis of constant rate period of spray drying of slurry”

Previously developed model for spray drying of slurry droplets with high solid content (Liang, 2001) was revised to describe correctly a boundary condition on the outer surface of droplet on basis of the rate of liquid evaporation.     

沉淀包覆法合成高活性纳米过渡态Al2O3粉

引言 为了提高氧化铝陶瓷的强度、韧性、致密度、透明性或降低其烧结温度等,要求采用纯度高、粒径小、粒度分布范围窄、烧结活性高的超细氧化铝粉为原料.     

我国干燥技术和装备的研究及应用

介绍我国干燥设备的开发、研究和应用情况。情况表明：我国干燥技术有很大的进步，大批进口干燥器的时代已经结束。     

FP石膏在硫化轮胎模具上的应用

主要阐述FP石膏材料、制芯工艺过程及烘干工艺，阐述了应用硅橡胶母模复制石膏芯表面光洁度高，尺寸精度较好，硫化轮胎的铸造成品率达99％以上。     

Effect of Mode of Drying on Microstructure of Potato

Potato v. Irga was subjected to blanching, and thereafter was dried by convection, puff-drying, and freeze-drying. Microstructure of raw, blanched, and dried tissue was analyzed under the light microscope using computer image analysis. It was found that the tissue of the investigated variety is built up from cells much smaller than those described in literature for other cultivars. Blanching caused starch gelatinization and increase of cross-sectional area of cells. There was no evidence of broken cell walls. Convective drying resulted in cell shrinkage and some breaking of cell walls. It was estimated that some 12% of cells lost integrity during drying. Limited disintegration of the tissue caused by convective drying is attributed to small size of cells, large contact area, and high cohesive forces between cells. Puff-drying damaged the tissue much more than the convective drying. The most devastating to tissue microstructure was freeze-drying, probably freezing per se.     

氯气干燥系统的技术改造

介绍了引起氯气干燥系统设备管道漏裂、堵塞、腐蚀的原因及其危害性,提出了包括设定合理的工艺参数,严格执行操作规程及改造更新设备管路等解决措施。