全文获取类型
收费全文 | 39372篇 |
免费 | 3890篇 |
国内免费 | 2225篇 |
专业分类
电工技术 | 797篇 |
综合类 | 3973篇 |
化学工业 | 7255篇 |
金属工艺 | 4481篇 |
机械仪表 | 1873篇 |
建筑科学 | 9205篇 |
矿业工程 | 1878篇 |
能源动力 | 706篇 |
轻工业 | 2111篇 |
水利工程 | 1442篇 |
石油天然气 | 1268篇 |
武器工业 | 290篇 |
无线电 | 941篇 |
一般工业技术 | 5284篇 |
冶金工业 | 2845篇 |
原子能技术 | 149篇 |
自动化技术 | 989篇 |
出版年
2024年 | 167篇 |
2023年 | 546篇 |
2022年 | 1038篇 |
2021年 | 1335篇 |
2020年 | 1279篇 |
2019年 | 1119篇 |
2018年 | 1171篇 |
2017年 | 1542篇 |
2016年 | 1568篇 |
2015年 | 1601篇 |
2014年 | 2339篇 |
2013年 | 2659篇 |
2012年 | 2812篇 |
2011年 | 2904篇 |
2010年 | 2130篇 |
2009年 | 2195篇 |
2008年 | 2068篇 |
2007年 | 2436篇 |
2006年 | 2233篇 |
2005年 | 1945篇 |
2004年 | 1667篇 |
2003年 | 1408篇 |
2002年 | 1233篇 |
2001年 | 1048篇 |
2000年 | 895篇 |
1999年 | 810篇 |
1998年 | 650篇 |
1997年 | 515篇 |
1996年 | 432篇 |
1995年 | 374篇 |
1994年 | 306篇 |
1993年 | 255篇 |
1992年 | 192篇 |
1991年 | 129篇 |
1990年 | 127篇 |
1989年 | 114篇 |
1988年 | 53篇 |
1987年 | 52篇 |
1986年 | 17篇 |
1985年 | 18篇 |
1984年 | 17篇 |
1983年 | 14篇 |
1982年 | 17篇 |
1981年 | 7篇 |
1980年 | 16篇 |
1979年 | 16篇 |
1964年 | 4篇 |
1963年 | 2篇 |
1961年 | 2篇 |
1954年 | 3篇 |
排序方式: 共有10000条查询结果,搜索用时 0 毫秒
41.
为研究高性能混凝土的声波传播特性及实现其强度的快速、准确、无损检测,基于超声波检测方法,应用嫩江、多宝山附近的沙石料,对高性能混凝土对声波的扩散性及其抗压性能与声参量之间的模型关系进行了研究.建立了高性能混凝土抗压强度与声速之间的多种数学模型.通过实测检测数据进行验证,满足精度要求.高性能混凝土的非均质性降低,其抗压强度与声速相关性较好,用超声的方法完全可以实现强度的快速推定.同时,也为将来高性能混凝土地区强度推定曲线的建立奠定了研究基础. 相似文献
42.
采用水媒法制备了低取代度羧甲基纤维素,并用接枝聚合法制备了改性纤维素/丙烯酰胺水凝胶,考察了单体质量比、取代度等对水凝胶拉伸性能的影响.结果表明:对于接枝聚合反应,采用低取代度羧甲基纤维素可以提高纤维素的有效用量;当交联剂用量为180 mg/L、引发剂1 300 mg/L、低取代度羧甲基纤维素和丙烯酰胺质量比在1∶4 ~ 1∶4.5之间、单体质量分数为30%时,合成水凝胶的拉伸强度达到0.28 MPa;在此基础上,适量添加15%的淀粉可使水凝胶拉伸强度达到0.47 MPa;添加1%二氧化钛可使水凝胶拉伸强度达到0.38 MPa. 相似文献
43.
采用多弧离子镀设备,在高速钢W18Cr4V上先进行等离子氮化,再沉积TiN薄膜,研究了不同渗氮温度和时间对PN+TiN薄膜组织和性能的影响。结果表明,温度为500℃左右和时间为2h以上条件下对W18Cr4V进行渗氮处理后再沉积TiN薄膜,可以得到最佳的薄膜表面显微硬度(1800~2000HV0.05)和膜/基结合力(50N),涂层耐磨性也得到明显提高。 相似文献
44.
John S. Haggerty A. Lightfoot John E. Ritter Paul A. Gennari S. V. Nair 《Journal of the American Ceramic Society》1989,72(9):1675-1679
Reaction-bonded Si3 N4 (RBSN) made from high-purity Si powder is unusually resistant to degradation caused by exposures to air for up to 50 h at temperatures up to 1400°C. The weight gain during oxidation of this SiH4 -originating RBSN is approximately 10 times less than conventional RBSN. Contrary to normally observed strength degradations, room-temperature strengths of this high-purity, oxidized RBSN (avg = 435 MPa, max. = 668 MPa) remained at their unusually high, as-processed levels after 1000° and 1400°C oxidizing exposures. Fracture toughness values were unaffected by oxidation ( K IC = 2.3 to 2.4 MPa · m1/2 ). This superior oxidation resistance results from the high purity and the small diameter pore channels (0.01 to 0.06 μm) achieved in this SiH4 -originating RBSN. 相似文献
45.
Recently, it has been reported by our group and others1.2 that loss of curing agent is encountered during the curing of small droplets or thin films of amine cured epoxies. In our earlier study3 results were reported on loss of curing agent in small droplets used in conducting the rnicrobond, single fiber test for determination of interfacial shear strength (ISS). It was reported that use of a volatile curing agent (meta-phenylene diamine (m-PDA) with DGEBA resin) resulted in increasing amounts of curing agent being lost (as measured by T8 of the cured droplets) with decreasing droplet size during the processing procedure. Droplets smaller than 150 micrometers were seen to lose up to 40% of the curing agent leading to alteration of the mechanical properties of the droplet and, therefore, causing measured values of ISS to be exceedingly low. Use of a less volatile curing agent (Jeffamine 700, a polyether diamine, Texaco Specialty Chemicals) in combination with DGEBA resin produced results which indicated that loss of curing agent was not occuring. This study was undertaken to show the relationships between film (or droplet) size and the amount of curing agent lost (during the processing) for three different aminecured epoxy systems. 相似文献
46.
The object of the present study was to investigate the effect of superimposed dynamic and static stresses on mechanical and thermal properties of some epoxy adhesives. It was found that combinations of shear creep and torsional oscillations, applied simultaneously to adhesive joints at temperatures within the glassy range of the adhesive, led to strengthening of the joints in shear and to an increase in the glass transition temperature of the adhesive. Similar loading stresses applied at temperatures close to the Tg of the adhesive, led to opposite effects on the above mentioned properties of the joints. The width of the glassy-rubbery transition of the adhesives increased, in the whole range of temperatures used in this study and for all epoxy compositions, as a result of subjecting the joints to superimposed dynamic and static stresses. The broadening of the glass transition was interpreted as a result of the stiffening of polymer network during the combined stressing experiments. A linear relationship was found between the area of endothermal peaks in the first DSC scan of specimens subjected prior to test to superimposed dynamic and static stresses at temperatures below Tg, and the shear strength of the joints. In agreement with this observation and with literature data, a linear relationship was revealed also between the glass transition temperature of the resins (measured in the first DSC scan) and the shear strength of the joints. Based on experimental observations and on some literature information, it was suggested that the strengthening of the joint, as well as the changes in thermal properties of the adhesives, are mainly due to physical processes, such as short-range orientation of network chains and an increase in intermolecular interaction between highly polar sites of the network. The possibility that superimposed stressing led to changes in chemical crosslinking was discussed but it seems that no such reactions occurred. 相似文献
47.
主要介绍了粘接技术在高功率铁氧体移相器上的应用。通过对其工艺途径及关键工序的控制,提出了采用粘接技术完成高功率移相器铁氧体的连接,不仅可以大量地缩短工作时间,而且可以使制造成本大幅度降低。 相似文献
48.
轧机机架强度和刚度的研究 总被引:3,自引:0,他引:3
本文对轧机机架的强度和刚度进行了研究。研究结果表明,增加机架横梁的高度是改善轧机机架刚度最有效也是最经济合理的方法。 相似文献
49.
50.
对调质状态800MPa低合金高强度钢及其焊接接头进行了系列温度的断裂韧性测试,讨论不同焊接方法对焊接接头断裂韧性的影响。发现板材的轧制方向对断裂韧性影响显著,LT方向试件的断裂韧性远超过TL方向试件的断裂韧性。在-60℃以上,母材处于上平台延性断裂范畴。在-80℃,裂纹扩展过程中有延脆断裂模式的转变。焊条电弧焊焊缝的断裂韧性与气体保护焊焊缝的断裂韧性相当。尽管常温下焊缝金属的断裂韧性甚至优于母材,但随着试验温度的降低,焊缝金属的断裂韧性迅速下降。在-20℃已发生断裂模式转变,这在结构服役时要引起重视。本研究为大型工程机械的断裂安全评定奠定了基础。 相似文献