套保稠油油田火烧油层可行性分析

从火烧油层的筛选标准、实际地质条件及室内物理模拟实验入手，对该油田火烧可行性进行了分析。分析结果认为，套保油田进行火烧总体上是可行的，在实际火烧时应避开底水的影响，火烧区域应选在构造高部位或仅烧其主力层。     

ICD in perspective: Putting social responsibility into practice

The Industry Council for Development (ICD) is an Industry Non Governmental Organisation established in 1990; it aims to contribute to improving public health through partnership projects on food safety and nutrition. This paper presents ICD’s activities in the past years and explains the reasons why the food industry should have a vested interest in supporting training and education of health professionals in food safety.     

The measurement of the diffusion coefficient and the sorption isotherm of water in paint films

An experimental technique together with a numerical model is proposed with which the diffusion coefficient and the sorption isotherm of water in paint can be measured. Inside a closed vessel, paint films are on stainless-steel plates. Water is present as water vapour in the air and in the paint. After blowing dry or wet air through the vessel for some time, the situation moves to a new equilibrium. The relative humidity of the air inside the vessel is measured as a function of time. From fitting the theoretical/numerical model against the experimental values, follow the diffusion coefficient and the sorption isotherm of water in the paint. The results show large scattering. When the independently measured sorption isotherm is used as an input parameter in the model, the fitting procedure gives much smaller scattering for the diffusion coefficient.     

聚甲亚胺改性尼龙6复合材料的等温结晶动力学

采用差示扫描量热法（DSC）对聚甲亚胺（PAM）/尼龙6复合材料等温结晶过程进行了研究。结果表明，PAM的加入使得基体的结晶速率增大，尤其是当含量为5%时，半结晶期明显减少。研究还发现，该体系的等温结晶过程完全可以用Avrami方程来描述，各试样的Avrami指数均在2-3之间，表明Avrami指数，球晶生长方式基本不受聚甲亚胺加入的影响。基体中原位形成的聚甲胺微纤起到了诱导结晶的作用，使得基体的结晶速率加快，但随着微纤含量的增加，由于分散性能变差而使得诱导结晶的能力减弱，表现为结晶速率又有所降低。     

低温低渗透砂岩油藏窜流大孔道深部封堵技术研究

所用堵剂为高强度的淀粉接枝聚丙烯酰胺交联凝胶SAMG-1,由<6%淀粉、4.5%-5.5%丙烯酰胺、0.003%-0.006%交联剂组成,35℃成胶时间受淀粉和交联剂用量控制,为18-20小时以上,成胶前黏度-100 mPa.s。该堵剂具有长期稳定性,在储层岩心中注入深度15 cm的堵剂,在35℃候凝48小时后及老化90天后,封堵强度分别为0.61和0.59 MPa/cm,封堵率分别为98.6%和98.1%。该堵剂优先进入高渗层,注入0.5 PV并成胶后,2组双填砂管组成的模型低、高渗管渗透率保留率分别为68.4%、0.7%和69.4%、0.0%。吉林扶余油田西一区+15-8.2区块有水井6口,油井13口,含水率达91.5%,注入水最快在5天内到达油井。报道了该区块整体深部调剖封堵窜流通道的情况,详细叙述了+15-9.2井施工中通过注入压力和井底回压控制注入流量,使堵剂陆续进入原生和次生孔道的工艺作业,该井设计注入堵剂92 m3。6口水井整体调剖后,油井产液量差别减小,产油量增加,有效期已超过了9个月,共增油843 t,含水平均下降3.87%。图7表1参8。     

Scale Up from Small Oven-Drying Tests of Mineral Concentrate to Pilot-Scale Drying with a Heated Pad

While Fickian diffusion models are commonly used in other applications, there are few reports of them being applied to the batch drying of a mineral concentrate. Diffusion coefficients estimated from small-scale oven-drying tests were used to predict the drying behavior of a concentrate sample 1 m × 1 m in area and 50 cm deep, with a heated bottom pad. These pilot-scale tests included both daily turning of the sample and turning every three days. The excellent quantitative agreement between the predicted and observed pilot-scale behavior gives a high level of confidence in the model predictions and suggests that a Fickian diffusion model is adequate to predict the behavior of mineral concentrates at the low moisture contents used here.     

多传感器目标的模糊识别

根据模糊理论，采用信息融合技术和模糊识别技术，讨论了在多类传感器网内进行多目标模糊识别的一般原理和方法。     

饼干炉湿度控制的改进方法

在大空间的温度控制系统中 ,采用简单的PID控制规律 ,对空间的温度、湿度进行解藕计算 ,将空间的相对湿度控制转化为送风含湿量的控制。该控制方式稳定、可靠 ,并且节约能源。本方法适用于所有的烘烤炉中     

On the determination of optimal transition profile of a stepped bar in tension or in torsion by BEM

The objective is to have uniformly distributed tangential stresses on the transition profile of a stepped bar subjected to tensile and torsional loading using an axisymmetric boundary element formulation. The transition curve is represented by the Langragian interpolation polynomial with progressive degrees to avoid shape distortion during the optimization procedure. The calculated result is compared with that obtained by fluid dynamics given in the literature. It is seen that the transition curve obtained in this paper is reasonable.     

用超声波技术测量螺栓轴向紧固应力

超声波速度会因材料中加载应力而产生微小的变化，这一现象特别适用于测量螺栓的轴向应力。根据螺栓的轴向应力与超声波传播时间变化率的关系，作者研究了一种可直接测量螺栓轴同应力的仪器。实验结果显示，本项技术十分适合现场的实际应用。