The Clausius inequality corrected for heat transfer involving radiation

The objective of this paper is to prove that the Clausius inequality must be re-stated to have general applicability for heat transfer involving radiative fluxes. The integrand (đQ/T) of the Clausius expression applies to heat conduction and convection, but does not hold for most radiative transfer scenarios, with the exception of reversible infinitesimal net blackbody radiation transfer. In other cases involving radiative transfer, the equality holds for a cycle even though irreversible heat addition by radiative transfer occurs. This is without the erroneous presumption of entropy destruction anywhere in the cycle. Thus, the Clausius inequality indicates reversibility for a cycle that includes an irreversible process. Further, in some radiative cases the quantity đQ/T, where T is the boundary temperature, is not the entropy transfer at the system boundary, and in fact, primarily represents entropy production within the system. It is also clear that in another case considered, the quantity đQ/T had no physical meaning whatsoever. Consequently, the Clausius expression has been re-stated so that it is applicable to cycles with processes involving any form of heat transfer. A new integrand (đQ_cc/T + đS_Net,Rad) is presented, allowing the Clausius inequality to generally apply to all heat transfer scenarios. The work in this paper emphasizes the need to re-state other fundamental equations allowing applicability to all heat transfer processes, and draws attention to the unique character of radiative entropy calculations.     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

A simple handling technique for mammalian oocytes and embryos during preparation for transmission electron microscopy

Due to their small size, mammalian oocytes and embryos pose unique problems during preparation for transmission electron microscopy. This paper outlines a method which combines protein embedding with centrifugation to locate the specimens on the face of a Beem capsule mould. This method facilitates both the processing of oocytes with minimal loss and rapid location of the specimens within the block for simultaneous sectioning, staining and examination.     

Colour Centres and Energy Transfer in BaF2-xClx:Eu2+ Phosphors

The optical absorption spectra of BaF2-xClx:Eu2 after ultraviolet (UV) light excitation were investigated.The differences between the absorption spectra after and before excitation (DAS) were observed.The DAS increase at both the high and the low energy side of F band in BaF2-xClx:Eu2 after 245 nm UV light excitation.The bleach effect of UV light and the absorption of electrons in the valence band may account for the former and the formation of Fa centres (association of F(Cl-) centres), whose absorption band matches the HeNe laser better, may explain the latter.In the write-in process, the transfer of electrons is via tunneling.In the readout process, the transfer of electrons captured in F(F-) and Fa centres is more likely via tunneling, and that of F(Cl-) centres is more likely via conduction band.     

Evaluating the transfer of technology between application domains: a critical evaluation of the human component in the system

Technology can take many forms from the development of sophisticated electronics to the application of basic procedural principles. Technology transfer can also take several forms, however, in this case, it is the transfer of technological principles between application domains that is of primary interest. This paper presents a framework (the Five ‘M’s framework) that can be used to consider the likely success of technology transfer. The framework is based upon a sociotechnical system approach. The framework is illustrated with an evaluation of the introduction of intelligent cruise control into motor vehicles. It is argued that this is a technological concept first developed as an aerospace application in the form of the autopilot. In this case, it is argued that the transfer of this technology in its current form may potentially compromise safety.     

Discrimination of B–C–N nanotubes through energy-filtering electron microscopy

Various multi-walled nanotubes in the B–C–N system are thoroughly investigated using a JEOL-3100FEF high-resolution field emission transmission electron microscope operating at 300 kV and equipped with an in-column built Omega filter. Spatially-resolved B, C and N elemental maps of the nanotubes are constructed. It is realized that a wide variety of tubular arrays composed of B, C and N atoms may exist in the system. Sandwich-like BN-rich and C-rich alternating tubular shells, graphitic C layers inside and outside of pure BN shells induced either by surface contamination, or electron beam irradiation, separation of C-rich and BN-rich tubes and/or BN particles within tubular bunches may take place. One should carefully take these effects into account while analyzing nanotube physical properties, e.g., electrical or optical, rather than simply rely on electron energy loss spectra typically collected from B, C and N containing nanostructures as a whole. Striking dependence of an individual nanotube electrical conductivity on tubular shell chemistry is demonstrated using I–V curve recording in an atomic force microscope.     

Assessing organo-clay dispersion in polymer layered silicate nanocomposites: A SAXS approach

A SAXS method for the quantitative assessment of the morphology of polymer layered silicate nanocomposites is proposed. Fitting the SAXS patterns, the number of clay layers, the periodicity of the layers in the tactoids, the thickness of the regions interposed between the clay platelets and their distributions can be measured. A good agreement with TEM data was obtained, avoiding the inconsistencies with microscopical observations often reported in the literature.