不锈钢绕带容器环板与绕带端头的焊接

本文通过焊接试验对奥氏体不锈钢绕带容器环板与绕带焊接工艺进行了研究分析,并得出了合理的焊接方法和工艺参数。     

硫脲型整合树脂在分析上的应用 Ⅰ.岩样中微量银的中子活化分析

前言银和其他贵金属元素一样,在地壳中比较稀少,按其自然丰度为第67号元素,平均含量仅0.07 ppm。由于地质样品成分非常复杂,为测定其微量银,必须进行严格的化学分离。但是迄今文献中报道的许多分离分法,步骤都相当冗长,一般采用氯化银反     

Synthetic resins: XV. Chelation ion exchange properties of 2,4- dinitrophenylhydrazone of resacetophenone-formaldehyde resin

A number of copolymers were synthesised by condensing the 2,4-dinitrophenylhydrazone of resacetophenone with substituted benzoic acids/ phenols and formaldehyde in the presence of sodium hydroxide or hydrochloric acid. The decomposition temperature, solubility and viscosity of the polymers have been determined. The ion-exchange properties have been studied by using a batch equilibrium method. The distribution of a number of metal ions between an aqueous solution and the resin have been measured. A wide range of pH and variable ionic strengths have been investigated.     

Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

Changes in the dielectric relaxations of water in epoxy resin as a function of the extent of water ingress in carbon fibre composites

Dielectric relaxation measurements are reported over a frequency range from 10⁻¹ to 10⁹ Hz as a function of exposure time for an epoxy resin-carbon fibre composite, ageing at 60 °C in water. Investigation of the nature of the dipole relaxation of the water molecules, indicates the nature of their interaction with the polymer matrix. Analysis of the dielectric relaxation spectra allow identification of processes that can be attributed to ‘free’ and ‘bonded’ water, water in micro-cracking, located in carbon fibre disbonds and plasticizing the polymer matrix. Identification of the various types of location in which water exists was aided by use of the N_g factor from the Kirkwood-Frölich equation, which describes the constraints on free dipole ration nature imposed by the environment in which it is located. These data indicate the power of the dielectric technique for quantitative analysis of water ingress into epoxy composites.     

Characterization of resol resins modified by the addition of PVC plastisols

Plastisols, which are a blend of poly(vinyl chloride) resin and a plasticizer (DEHP), were used as a toughening agent of a resol resin in order to improve the mechanical properties. It was not possible to formulate resol blends by adding more than 10 % of plastisol owing to a lack of apparent homogeneity in the systems, which also showed many air bubbles. The relationship between dynamic mechanical, mechanical and thermal properties and the amount of plastisol added was studied. It was determined from the infrared spectroscopy and dynamic mechanical results that the resol–plastisol blends seem to be formed by a reaction between the phenol and PVC giving a higher crosslinked structure. An improvement in the thermal resistance of the blends at lower temperatures was observed with an increase in the percentage of plastisol. Flexural analysis showed the elastic behaviour of the systems. However, it was not possible to observe the effect of the plasticizer (DEHP) owing to the low quantity of plastisol that was added to the resol. Copyright © 2004 Society of Chemical Industry     

龙潭拱坝砼上坝运输方案选择

龙潭拱坝坝高９０ｍ，砼上坝运输是砼施工过程中的中间环节，控制进度的关键，必须因时因地制宜地选择适当的运输机械和运输方案，使砼运输能做到保质、保量、及时和经济，通过论证比较，结合本工程现实情况，砼上坝运输不采用缆机而采用门机方案．     

北京核电站模拟器硬件的功能和特点

本文介绍北京核电站模拟器硬件构成并分析其功能和特点。     

Automatic optical inspection of plated through-holes for ultrahigh density printed wiring boards

An automatic optical through-hole inspection system for ultrahigh density printed wiring boards (PWBs) using leakage light detection has been developed. To detect the dim leakage light emitted from the through-hole defect, we enhanced the sensitivity of the light detector 150 times using a microchannel plate tube. However, the tube caused two problems: stray light sensing and image distortion. To solve these problems, we optically isolated the sensing optics and developed a distortion correction method. We have developed a prototype system that can detect a defect as small as 100 m.     

铸造用CO2硬化冷芯盒材料及工艺的发展

铸造用CO2硬化粘结剂系统具有气硬冷芯盒的优点,同时又具有环保方面的优势。主要介绍了水玻璃-CO2法、聚丙烯酸钠-CO2法、酚醛树脂-CO2法三种工艺。这些工艺方法近年来国内外研究较多,并且取得了很大进展。