Laser melting of Ti-15Al-20Nb alloy

Titanium aluminides have become promising materials for high-temperature applications, but the relatively poor oxidation resistance and elevated- temperature strength of these alloys limit their application to temperatures lower than 1000 °C. Niobium addition improves the properties of titanium aluminide. However, the mechanical, metallurgical, and corrosion properties of Ti- Al- Nb may be improved by treatment with a laser beam. Consequently, the present study examines the properties of Ti- 15Al- 20Nb alloy subjected to the Nd:YAG laser melting process. Hardness in the surface region increases to twice the base material hardness, and corrosion resistance improves considerably after laser treatment.     

表面处理对球墨铸铁接触疲劳性能的影响

本文研究了激光微熔处理和高频感应加热淬火对球墨铸铁表面组织、接触疲劳强度和接触疲劳破坏过程的影响。结果表明,激光处理和高频淬火均可提高球铁的接触疲劳强度,但其接触疲劳破坏过程和形式却不同,前者是由于硬化层与基体间裂纹扩展造成大块深层剥落,后者则是表层裂纹在油楔作用下造成小块浅层脱落。     

W18Cr4V高速钢激光相变强化层的残余应力

利用Ｘ射线衍射法对Ｗ１８Ｃｒ４Ｖ高速钢激光相变强化层的残余应力进行了测定和分析。试验结果表明，相变强化层表面的残余应力为压应力，内部为拉应力，近似按正弦函数分布。其大小和分布状态随工艺参数的变化而改变。当改变工艺参数使表面熔化时，表面为拉应力。     

Ba—P复合变质对铝硅合金初晶硅的细化作用

研究了钡、磷及钡磷复台变质对过共晶铝硅合金初晶硅的细化作用，发现钡变质可细化初晶硅的尺寸，同时使硅晶体由板块状改变为树枝状；磷变质可明显细化初晶硅，但对其形状因子改变不大；但磷复合变质综合了二者的优势。硅晶体表面有钡或钡的化合物的吸附，认为吸附抑制机制是钡变质的实质。     

激光快速修复Ti-6Al-4V合金的显微组织与力学性能

针对Ti-6Al-4V合金在加工和服役过程中的损伤特点,对Ti-6Al-4V合金锻件的3种典型误加工缺陷——槽缺陷、面缺陷和体缺陷进行了激光快速修复研究。激光修复区与锻件基体形成致密冶金结合,Al、V合金元素由锻件基体到激光修复区均匀分布,无宏观偏析。激光修复区组织为粗大原始β晶粒内分布细长的α针及编织细密的α+β板条组织,呈现典型的魏氏结构,热影响区组织从锻件的等轴α+转变β组织逐步过渡到魏氏(α+β)组织。对预制有3种类型缺陷的激光修复试样进行室温静载拉伸试验和硬度测试,结果表明修复试样的拉伸性能达到锻件标准(HB5224-1982)。激光修复试样的硬度和强度高于锻件基体,而塑性则低于锻件基体。因此,激光修复区和锻件基体可看作是一种“强+弱”的组合,这与二者的显微组织是相对应的。     

侧吹气流方向对大功率CO2激光焊缝成形的影响

激光深熔焊过程中会在熔池上方产生等离子体云，若该等离子体云过密，将降低激光入射到工件表面能量密度。在工业应用中，常采用侧吹辅助气体来减弱等离子体云的影响。本文通过试验，研究了在不同气体流量下，侧吹气体方向不同对焊接过程稳定性和焊缝成形的影响。结果发现：使用大功率CO2激光焊接AH32时。侧吹气体方向对焊缝成形有着明显的影响。从熔池和等离子体两个方面，解释了侧吹气体方向的影响机制。     

Microstructure and formation mechanism of titanium matrix composites coating on Ti-6Al-4V by laser cladding

Laser cladding experiments were done on a 5-kW continuous wave CO2 laser to synthesize TiC and TiB rein- fowed titanium matrix composite coatings on Ti-6AI-4V alloy with a mixture of Ti and B4C precursor powder. The ther- modynamics of the reactions were calculated and analyzed. The microstructure and phase evolution of TiB and TiC com- posites were investigated. The results showed that the chemical reaction between Ti and B4C would release much heat, and these compounds, TiC, TiB, and small amount of TiB2, can be formed on the surface of Ti-6AI-4V alloy if the supplied en- ergy is sufficient to excite the reaction among the initial products. A good metallurgical bond between the coating and the substrate can be achieved. The microhardness of coating was irregular and the maximum value was approximately HV600.     

激光熔炼W/W2Ni3Si金属硅化物“原位”复合材料的耐磨性

采用水冷铜模激光合金熔炼炉制备了以初生w树枝晶为增强相、以w2Ni3Si三元金属硅化物为基体的金属硅化物“原位”耐磨复合材料．分别在室温干滑动磨损及600℃高温滑动磨损条件下测试了上述W／W2Ni3Si金属硅化物“原位”增强耐磨复合材料的耐磨性，并讨论了其磨损机理．结果表明，上述金属硅化物耐磨复合材料在室温干滑动磨损和高温滑动磨损条件下均具有优异的耐磨性能．     

钛基复合材料激光熔覆层显微组织及其强化机制

利用激光熔覆技术在Ti-6A1-4V合金表面制备了TiC增强钛基复合材料涂层，复合材料的硬度明显高于基体，平均硬度可达940HV0.2。对复合材料的显微组织分析表明：TiC增强钛基复合材料的强化机制以细晶强化和弥散强化为主。     

激光熔凝的数值模拟及其在激光定向凝固中的应用

建立了一套激光熔凝的数学模型和计算方法 ,给出了两种条件下熔池深度与扫描速度的关系曲线。计算结果与实验值吻合良好 ,验证了模型的有效性。根据计算分析了激光工艺参数与激光定向凝固组织的关系。据此通过工艺参数的匹配 ,在熔池顶部得到了与扫描方向完全一致的凝固组织