金属快速凝固的非平衡超急速传热模型

运用非Fourier传热理论建立了金属快速凝固过程中的非平衡传热理论模型，包括非Fourier方程的建立、传热与相变模拟，模拟计算表明：（1）在溅射激冷条件下，界面换热系数越大，界面冷却速度和移动速度也越高。在界面换热系数相同时，计算得到的界面冷却速度随着固－液界面高度的提高呈现先上升而后下降的变化趋势；计算得到的冷却速度值明显小于Fourier定律的计算值。（2）在激光加热条件下，计算的界面移动速度在凝固开始时先急剧增加，然后渐趋平稳，计算还表明，金属的过热及过冷度与其热物性相关。     

The significance of deposition point standoff variations in multiple-layer coaxial laser cladding (coaxial cladding standoff effects)

Direct laser deposition (DLD) is an additive manufacturing process that builds up a part layer-by-layer by fusing metal powder to a solid substrate. A coaxial laser and powder delivery head is commonly used, and here a critical process variable is the standoff distance between the nozzle and the material deposition point. This contribution investigates the role of this variable and the effect that it has on the final part geometry. The experimental results show that good layer consistency can, in fact, be obtained with no movement of the substrate between layers for more than 20 layers, or 10 mm under tested conditions, and that poorer results are obtained by regular movement of the substrate by a badly chosen constant amount. A theoretical analysis of the situation establishes a method to estimate melt pool size using an analytically calculated temperature near the heat source. Based on this, simple heat and mass flow models are established to allow some of the results to be explained.     

The yttrium effect on the corrosion resistance of CO2-laser processed MCrAlY coatings

To improve the corrosion resistance and to study the effect of yttrium in the behavior of coatings produced by thermal spraying MCrAlY (M=Ni, Co) powders, CO₂ laser processing was conducted. Three methods were used: (1) a combination of gas flame and plasma spraying in air followed by laser glazing in argon, (2) low-pressure plasma spraying (LPPS) and laser glazing in argon, and (3) LPPS and laser-gas (O₂) alloying. Laser glazing in argon of the MCrAlY coatings sprayed in air promoted formation of weakly adherent agglomerates of Al–Y oxides and an alumina-chromia solid solution. Glazing in argon atmosphere of LPPS CoNiCrAlY and NiCrAlY coatings caused the formation of nickel aluminides besides the formation of Y–Al compounds. Gas (O₂)-alloying of these coatings produces continuous and adherent (yttrium-containing) alumina and chromia layers. The effects of yttrium on the characteristics of the oxides formed in the coatings during laser glazing, laser-gas alloying, and high-temperature oxidation is discussed. This work also investigated the oxidation resistance of the laser-processed MCrAlY coatings in air and in the presence of 85 mol/o V₂O₅–Na₂SO₄ fused salt at 900°C.     

激光近成形金属零件过程中涂覆层的组织及性能

利用激光近成形技术，在1Cr18Ni9Ti不锈钢基体上采用镍基合金和钴基合金粉末进行单道涂覆烧结试验，获得具有快速凝固组织特征的激光涂覆层，并分析了影响涂覆层组织和质量的激光参数和工艺参数。     

硼铸铁缸套激光表面熔凝组织和性能的研究

为了提高硼铸铁缸套的耐磨性能，对硼铸铁气缸套进行激光熔凝处理。利用扫描电子显微镜观察了激光熔凝处理后的显微组织。利用显微硬度计检测了激光熔凝组织的显微硬度，同时进行了以GCr15钢标准环为配副的环块磨损试验。研究结果表明，硼铸铁经激光熔凝处理后得到了共晶莱氏体 马氏体组织，而且激光熔覆层厚度可控，组织和性能稳定，熔凝强化表层显微硬度达到800-1200HV0.2。磨损试验结果显示，激光熔凝处理后，磨损截面积比未处理的试样减小了44.4%，从而表明激光熔凝处理是提高硼铸铁缸套耐磨性能的有效手段。     

送粉激光熔覆合成制备WC/Ni硬质合金涂层及其耐磨性

借助同轴送粉法将W／C／Ni元素混合粉末送入熔池，利用激光熔池中热力学和动力学条件，在优化材料威分和激光熔覆工艺参数条件下可以直接反应合成出WC颗粒，形成以WC／Ni为主的复合涂层。熔覆层中含有WC，CW3，α-W2C，W2C，Fe6W6，C,FeW3C，W3O，C等相。添加2wt％的Cr3C2可以细化涂层中的WC颗粒尺寸，颗粒平均尺寸为4～6μm，硬度值为85HRA左右。激光合成制备的WC／Ni硬质合金涂层的耐磨性尚不及YG8硬质合金的耐磨性，但比渗氮处理试块的耐磨性提高了7．9倍。激光直接合成硬质合金涂层的成本低，可在零件能任何部位原位合成，形状尺寸不受限制。     

低合金奥－贝球铁电弧焊焊条的研究

本文通过等温热处理系统地研究了Ｃｕ、Ｎｉ、Ｍｏ对球铁焊缝金属等温转变，奥－贝化能力及机械性能的影响，井利用Ｘ射线衍射仪、扫描电镜、透射电镜研究了低合金奥－贝球铁焊缝的基体结构，分析讨论了其强韧化机制，在此基础上首次研制成功了Ｎｉ－Ｍｏ低合金奥－贝球铁析焊分，与非合金化奥－贝球铁焊条相比，焊缝金属的奥－贝化能力提高２．５倍，其焊缝与焊接接头的机械性能均满足奥－贝球铁的要求。     

Effects of laser beam energy and incident angle on the pulse laser welding of stainless steel thin sheet

This paper reports an experimental study of laser spot welding on stainless steel sheets. A pulsed Nd:YAG laser was used to weld the stainless steel specimen in the range of laser energy 0.6–1.2 J and incident angle 30–75° (the angle of the laser beam incident direction to the sheet surface). Metallography was applied to measure the cross-sectional size and shape of the welded spot. From the experimental results, it is found that as the laser energy increases, the penetration depth, bead length, and bead width of the welded spot increase. As the laser incident angle increases, the penetration depth and the bead width increase while the bead length decreases. The results illustrate that the shape and size of the welded spot depend not only on the laser energy, but also on the incident angle of laser beam.     

基于选择性激光烧结方法的金属零件快速制造技术研究

主要研究了通过选择性激光烧结高分子原型件制造金属零件的工艺。通过采用真空压差铸造工艺。结合铸造型壳的制造，成功制造出金属零件。对基于SLS技术的精密铸造过程中的精度控制进行了研究分析，并提出了解决办法。     

声光调Q Nd:YAG脉冲激光修锐树脂结合剂CBN砂轮

采用声光调Q Nd:YAG脉冲激光径向辐照，对树脂结合剂CBN砂轮进行修锐试验研究。研究了单脉冲激光辐照下，平均功率，脉冲频率和离焦量等参数对烧蚀凹坑深度的影响，由此可方便获得合适的激光修锐参数；分析了声光调Q YAG脉冲激光修锐树脂CBN砂轮的选择性去除机理，观察并比较了声光调Q脉冲激光，连续激光和机械法修锐后砂轮表面的地形地貌，试验表明声光调Q Nd:YAG脉冲激光径向辐照修锐树脂CBN砂轮，可获得更为良好的修锐效果。