铝－锂合金中δ’（Al＿3Li）沉淀相时效粗化行为及体积分数的测定

对经固溶处理的二种Ａｌ－Ｌｉ合金（１．９４ｗｔ．％Ｌｉ和２．７５ｗｔ．％Ｌｉ）的时效过程进行了研究。结果表明：δ’的生长速率遵从Ｏｓｔｗａｒｄ粗化动力学。１．９４ｗｔ．％Ｌｉ合金δ’产生于时效过程中，而２．７５ｗｔ．％Ｌｉ合金的δ’产生于时效的前期阶段。前者的表现体积分数明显大于根据相图估算的数伍，真实体积分数则与此值接近；后者的体积分数低于根据相图估算的数值，这可能归咎于δ’固相线的位置、统计学误差及Ｌｉ更易在时效过程中贫化。     

Analysis of supersaturation and nucleation in a moving solution droplet with flowing supercritical carbon dioxide

A supercritical antisolvent (SAS) process is employed for production of solid nanoparticles from atomized droplets of dilute solution in a flowing supercritical carbon dioxide (SC CO₂) stream by attaining extremely high, very rapid, and uniform supersaturation. This is facilitated by a two‐way mass transfer of CO₂ and solvent, to and from the droplet respectively, rendering rapid reduction in equilibrium solubility of the solid solute in the ternary solution. The present work analyses the degree of supersaturation and nucleation kinetics in a single droplet of cholesterol solution in acetone during its flight in a flowing SC CO₂ stream. Both temperature and composition are assumed to be uniform within the droplet, and their variations with time are calculated by balancing the heat and mass transfer fluxes to and from the droplet. The equilibrium solubility of cholesterol with CO₂ dissolution has been predicted as being directly proportional to the Partial Molar Volume Fraction (PMVF) of acetone in the binary (CO₂–acetone) system. The degree of supersaturation has been simulated up to the time required to attain almost zero cholesterol solubility in the droplet for evaluating the rate of nucleation and the size of the stable critical nuclei formed. The effects of process parameters have been analysed in the pressure range of 7.1–35.0 MPa, temperature range of 313–333 K, SC CO₂ flow rate of 0.1136–1.136 mol s^?1, the ratio of the volumetric flow rates of CO₂‐to‐solution in the range of 100–1000, and the initial mole fraction of cholesterol in acetone solution in the range of 0.0025–0.010. The results confirm an extremely high and rapid increase in degree of supersaturation, very high nucleation rates and stable critical nucleus diameter of the order of a nanometre. Copyright © 2005 Society of Chemical Industry     

Recursive calculation of ladder circuit frequency functions

It is shown how the transfer function as well as the input impedance and admittance of any linear time-invariant ladder circuit can be determined in closed form as frequency functions dependent upon the network element parameters. All elements of the ladder circuit must be explicitly specified by their frequency characteristics. The results are achieved with the aid of recursive algorithms. The outcome is demonstrated by means of an example.     

低剂量X射线照射诱导HeLa细胞存活的

采用集落形成法观察了低剂量X射线照射HeLa细胞的存活率，结果表明，小于0．5Gy的X射线照射细胞的存活率高于对照，得到了HeLa细胞存活的“兴奋效应”，而且在0．25Gy附近这种效应更为明显；低剂量D1（0．05，0．75Gy)的预照射降低了随后攻击量D2对细胞的损伤程度，反映出低剂量照射可诱发细胞存活的“适应性反应”。     

Surface Hardening of High-Strength Low Alloy Steels (HSLA) Dual-Phase Steels by Ball Burnishing Using Factorial Design

Burnishing is used increasingly as a finishing operation which gives additional advantages such as increased hardness, fatigue strength, and wear resistance. Experimental work based on 3⁴ factorial design was carried out to establish the effects of ball burnishing parameters on the surface hardness of high-strength low alloy steels (HSLA) dual-phase (DP) steel specimens. Statistical analysis of the results shows that the speed, feed, lubricant and ball diameter have significant effect on surface hardness.     

纤维体积分数对K3D/MCPA复合材料力学性能的影响

本文研究了纤维体积分数对三维编织芳纶纤维增强铸性尼龙(简称K3D／MCPA)复合材料力学性能的影响。研究表明，K3D／MCPA复合材料有优异的抗冲击性能，冲击强度比三维编织芳纶纤维增强铸性尼龙(简称C3D／MCPA)和纯基体均有大幅度的提高，且随着纤维体积的提高而升高。K3D／MCPA复合材料剪切强度随纤维体积比的增大而增大，其纵向剪切强度低于纯基体和C3D／MCPA复合材料，但其横向剪切强度高于它们。K3D／MCPA复合材料弯曲强度与弯曲模量随纤维体积比的提高而提高，但与相同体积比的C3D／MCPA相比，K3D／MCPA的弯曲强度与弯曲模量均较低。     

裂解碳五馏分分离中取代二萃单元的研究

针对目前裂解碳五馏分分离流程中第二萃取单元的诸多问题,提出采用选择性加氢除去炔烃后再进行精馏的方法代替二萃单元,得到聚合级异戊二烯产品。研究结果表明,工艺流程的改进部分是可行的,具有流程短、安全可靠、能耗低、生产成本低、环境污染少、简化溶剂回收单元等优点。     

涡流管类比逆流换热器方法的研究

结合Scheper，Lewins和Bejan的理论模型，对涡流管类比逆流换热器模型进行了深入地分析，得出了冷流分量对温度分离效应的函数关系式，为了解涡流管机理和实验中强化涡流管温度分离效应提供了理论依据。     

电解法烟道气二氧化硫在线监测系统的设计

介绍了一种烟道气中SO2在线检测系统，该系统可以实现24h不间断地监测烟道气中SO2的体积分数和质量浓度，同时将信息经网络传送给环保有关部门，具有一定的新颖性、可靠性、准确性。     

热轧带钢连续冷却过程中相变体积分数的计算

基于相变动力学原理 ,在充分考虑变形对相变影响的情况下研究了奥氏体向铁素体、珠光体和贝氏体相变的动力学。探索了热轧带钢连续冷却过程中相变体积分数的计算方法。用此方法进行的计算机模拟与实验结果相当吻合。