Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Cover Picture: Light‐Emitting Organic Solar Cells Based on a 3D Conjugated System with Internal Charge Transfer (Adv. Mater. 22/2006)

The cover image illustrates the dual photovoltaic and electroluminescence function of a single‐layer device based on a thienylenevinylene–triphenylamine with internal charge transfer (ICT), as reported by Cravino, Roncali, and co‐workers on p. 3033. The material forms an organic glass with isotropic electronic properties while ICT leads simultaneously to an extension of the photoresponse to the red and to an increase of the open circuit voltage. The use of an additional layer of C₆₀ further improves the photovoltaic. Images of the sun and moon courtesy NASA/JPL–Caltech.     

Effect of polymerization conditions on o‐phenylenediamine and o‐phenetidine oxidative copolymers

A series of new o‐phenylenediamine (OPD)/o‐phenetidine (PHT) copolymers with partly phenazine‐like structures has been successfully synthesized at three polymerization temperatures by chemically oxidative polymerization in four different polymerization media. The molecular structures and properties of the resulting OPD/PHT polymers were investigated by IR, UV–vis and high‐resolution ¹H NMR spectroscopies, and DSC, in order to ascertain the effect of reaction temperature, comonomer ratio and acid medium. The copolymerization mechanism of OPD with PHT monomers has been proposed. It is found that the statistical OPD/PHT copolymer obtained at a temperature of 118 °C has a higher degree of polymerization than that obtained at 12–17 °C. The OPD content in the copolymers calculated from NMR spectroscopic analysis is higher than that in the feed OPD content, whereas the OPD content calculated from element analysis is slightly lower than the feed OPD content. It can be predicted that denitrogenation takes place in the OPD units during the polymerization process at OPD/PHT molar ratios of 90/10 and 100/0. These OPD/PHT copolymers exhibit a much better solubility than the OPD homopolymer, hence suggesting an incorporation of PHT units into the phenazine structure of the homopolymer. The thermal behavior of the copolymers was also studied. Copyright © 2004 Society of Chemical Industry     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Thermodynamic state of reinforced interpenetrating polymer networks

The free energies of mixing of two networks in the interpenetrating polymer network based on crosslinked polyurethane and poly(ester acrylate) have been determined by the vapour sorption method. It was established that the constituent networks in the IPN are not miscible. The introduction of fillers of different chemical nature increases the compatibility. The thermodynamic affinity of the fillers to the individual networks and IPN was estimated. It was established that when the free energy of interaction of one or both components of the IPN with the filler is negative, reinforcement leads to the formation of a compatible and equilibrium system. For fillers having no affinity to the polymers, compatibilization is observed, which is connected with slowing down of phase separation in the system in the presence of filler.     

钢纤维聚合物混凝土抗压本构关系

钢纤维聚合物混凝土是由聚合物混凝土基体和钢纤维共同组成的纤维增强复合材料，它的力学行为不仅依赖于聚合物混凝土基体的行为，而且与钢纤维的掺量、分散特征以及钢纤维的几何尺寸有关，本文将基于损伤力学原理研究在不同纤维掺量下的钢纤维聚合物混凝土的全程压力-应变曲线及其本构模型。     

Synthesis of poly(4-methylstyrene)- graft-poly(ethylene oxide)s and application as polymeric dispersant in coal-water mixture

Poly(4-methylstyrene)-graft-poly(ethylene oxide)s were prepared via polymerisation of ethylene oxide on to poly(4-methylstyrene)s functionalised with hydroxyl groups. In this way, many ‘comb-like’ polymers having different hydrophobic backbone length, hydrophilic branch length and frequency of branches were synthesised. These polymers were tested as dispersants in coal-water mixtures in order to correlate the dispersing properties of this class of polymers with the investigated parameters.     

Study on phase behavior–impact strength relationship of unsaturated polyester/polyurethane hybrid polymer network

The phase behavior of a hybrid polymer network (HPN) composed of poly[(propylene glycol maleate)-co-(propylene glycol phthalate)] crosslinked with styrene and polyester–urethane crosslinked with methylene-bis-ortho-chloroaniline was examined. The correlation between phase separation and impact strength of the HPNs is discussed. The composition of HPNs has an effect on their properties.     

Sidechain liquid crystal polymers

Research has continued in the field sidechain liquid crystal polymers over recent years, but it is becoming clearer that this research is being directed away from the traditional technology areas of electro-optic devices and researchers are developing new and exciting applications for this novel state of matter.     

Electrochemical,FTIR and morphological study of polypyrrole—Polystyrenesulphonate conducting films

The electrochemical behaviour, FTIR spectrum and the morphology of polypyrrole-polystyrenesulphonate (PPy-PSS) films obtained potentiostatically at 0.6 V in a 0.05m Py + 1.7 × 10^?2m NaPSS medium have been analysed. Different electrochemical parameters have been modified in order to establish the first polaron formation, the reversibility of the redox process and the doping mechanism. The FTIR spectrum confirms the existence of C?O groups in the film structure and two possible explanations are suggested. SEM reveals a higher homogeneity in these films than in PPy films doped with smaller counterions.