Deformation behaviour and oxidation resistance of single-phase and two-phase L21-ordered Fe–Al–Ti alloys

Single-phase Fe–Al–Ti alloys with the Heusler-type L2₁ structure and two-phase L2₁ Fe–Al–Ti alloys with MgZn₂-type Laves phase or Mn₂₃Th₆-type τ₂ phase precipitates were studied with respect to hardness at room temperature, compressive 0.2% yield stress at 20–1100 °C, brittle-to-ductile transition temperature (BDTT), creep resistance at 800 and 1000 °C and oxidation resistance at 20–1000 °C. At high temperatures the L2₁ Fe–Al–Ti alloys show considerable strength and creep resistance which are superior to other iron aluminide alloys. Alloys with not too high Ti and Al contents exhibit a yield stress anomaly with a maximum at temperatures as high as 750 °C. BDTT ranges between 675 and 900 °C. Oxidation at 900 °C is controlled by parabolic scale growth.     

采用消失模铸造工艺生产蠕铁排气出口管

介绍了消失模法生产蠕铁排气出口管的工艺过程.试验发现,采用反直浇道结合侧注的模组形式为佳,每组8件、管口朝下;涂料直接影响铸件表面积碳及皱皮倾向;并采用消失模法批量生产了蠕铁排气出口管,材料性能及金相组织达到要求,铸件壁厚均匀,表面光滑,已用于红旗轿车的部分车型.     

Corrosion protection of iron by polypyrrole modified by copper using the cementation process

Polypyrrole (PPy) coatings have been deposited on iron from aqueous oxalic acid solution at different current densities. The polymer deposit obtained at a current density of 2 mA cm⁻² yields strongly adherent and smooth PPy layers. The modification of the film by incorporation of copper microparticles using the cementation process was applied. The resulting PPy/Cu film electrodes were characterized by scanning electron microscopy and EDX analysis. The protective performance against corrosion of these films is evaluated by using open circuit potential monitoring in highly corrosive solution (3% NaCl + HCl, pH 1). The results obtained were promising in the protection against corrosion.     

熔模精铸球铁技术的研究与应用

对熔模精铸球铁技术进行了研究和试验，重点对熔炼、浇注及冷却过程进行了试验，确定了较合理的工艺参数。经试验，蜡模压型的铸造收缩率可在0．5％～1．2％之间选择；型壳采用硅溶胶-水玻璃复合粘结剂工艺；球铁的化学成分按C、Si含量较高，Mn、S、P含量较低的原则确定。经批生产考核，精铸球铁铸件的金相组织可达到球化级别2级，石墨球大小6级，珠光体含量10％的要求。铸件力学性能也满足使用要求。     

快速直接还原法生产金属化球团工艺的探讨

研究开发了冷固结含碳铁矿球团的还原工艺，它与环形转底炉相结合，形成快速直接还原新工艺，生产金属此球团，具有一系列优点，如：设备简单，生产效率高、能耗低等等。     

An empirical molecular docking study of a di-iron binding protein with iron ions

Various molecular docking software packages are available for modeling interactions between small molecules and proteins.However,there have been few reports of modeling the interactions between metal ions and metalloproteins.In this study,the AutoDock package was employed to example docking into a di-iron binding protein,bacterioferritin.Each binding site of this protein was tested for docking with iron ions.Blind docking experiments showed that all docking conformations converged into two clusters,one for internal iron binding in sites within the metalloprotein and the other for external iron binding on the protein surface.Local docking experiments showed that there were significant differences between two internal iron binding sites.Docking at one site gave a reasonable root-mean-square deviation(RMSD) distribution with relatively low binding energy.Analysis of the binding mode quality for this site revealed that more than half of the docking conformations were categorized as having good binding geometry,while no good conformations were found for the other site.Further investigations indicated that coordinating water molecules contributed to the stability of binding geometries.This study provides an empirical approach towards the study of molecular docking in metalloproteins.     

对钢铁企业可定制工作流的OA系统的设计与实现的探讨

本文从提升钢铁企业管理水平的角度入手,对钢铁企业可定制工作流的OA系统的设计与实现进行了探讨。     

重钢新区铁区MES系统研究与实施

针对重钢集团环保搬迁铁区生产单元信息化建设具体要求,开发并实施铁区MES系统,同时简要介绍系统功能及应用效果。     

钢铁企业全厂仪表维修设施设计初探

以我国某大型钢铁企业全厂仪表维修设施的设计方案为例,简要说明了仪修设施的设计原则、全厂仪表维修的一般解决方案,较详细地介绍了仪修设施专业划分、实验室及维修车间的设置和主要设备构成,为该类项目的设计和工程建设提供一定参考。     

Iron working at Zambana el Vato (TN), Italy

ABSTRACT

The workshop of Zambana el Vato (region Trentino, Northern Italy), is dated to the period between the 7th-6th and the 5th century BC. Iron working activities are clearly recognizable from the various finds. Among them there are working slag, heated clay, fragments of hearth or forge, hammerscale and more residues that can be referred to iron technology. A number of selected specimens were sectioned and mounted for photomicroscopy to identify the structure and some of the mounted samples were also examined by scanning electron microscopy (SEM) using both a back scattered electron detector and energy dispersive (EDS) x-ray analysis. This paper presents the results of these studies. The hearths were regularly repaired, as their fragments were found mixed with working slag. The hammerscale samples indicate that there were three iron-working areas. The fragments of forge with traces of tuyeres indicate that bellows were employed. Refining slag was identified among the debris. This is particularly significant as for the moment no iron refining centers are known in this area.