一种木材粘合剂胶接强度新型试验装置的研制

设计了一种由基础框架、加载液压千斤顶、测力弹簧、读数百分表和试样夹具组成的木材粘合剂胶接强度试验装置。有限元数值分析与通用材料试验机的测试比较结果表明：该装置可满足JIS K6852标准的要求，且具有结构简单、体积小、测量可靠和便捷的特点。     

Transient and steady-state deformations and breakup of dispersed-phase droplets of immiscible polymer blends in steady shear flow

Transient and steady-state deformations and breakup of viscoelastic polystyrene droplets dispersed in viscoelastic high-density polyethylene matrices were observed in a simple steady shear flow between two transparent parallel disks. By separately varying the elasticities of the individual blend components, the matrix shear viscosity, and the viscosity ratio, their effects on the transient deformation, steady-state droplet size, and the breakup sequence were determined. After the startup of a steady shear flow, the viscoelastic droplet initially exhibits oscillations of its length in the flow direction, but eventually stretches preferentially in the vorticity direction. We find that at fixed capillary number, the oscillation amplitude decreases with increasing droplet elasticity, while the oscillation period depends primarily on, and increases with, the viscosity ratio. At steady-state, the droplet length along the vorticity direction increases with increasing capillary number, viscosity ratio, and droplet elasticity. Remarkably, at a viscosity ratio of unity, the droplets remain in a nearly undeformed state as the capillary number is varied between 2 and 8, apparently because under these conditions a tendency for the droplets to widen in the vorticity direction counteracts their tendency to stretch in the flow direction. When a critical capillary number, Ca_c, is exceeded, the droplet finally stretches in the vorticity direction and forms a string which becomes thinner and finally breaks up, provided that the droplet elasticity is sufficiently high. For a fixed matrix shear stress and droplet elasticity, the steady-state deformation along the vorticity direction and the critical capillary number for breakup both increase with increasing viscosity ratio.     

稀土丁异戊橡胶改性天然橡胶的应用研究

采用稀土丁异戊橡胶代替顺丁橡胶，测试并分析了改性天然橡胶的低温性能及相关性能。结果表明，稀土丁异戊橡胶改性的天然橡胶室强力学性能和粘接性能与顺丁橡胶改性的天然橡胶相近，但低温性能有较大的改善。在-40℃下贮存2h后，顶丁橡胶改性天然橡胶硫化胶有明显的结晶现象，其剪切模量较室温下的相应值增加了6倍，而稀土丁异戊橡胶改性的天然橡胶硫化胶保持了良好的弹性，其剪切模量值与室温下的相当。     

Failure load prediction of structural adhesive joints : Part 2: Experimental study

The objective of this study was to determine how the fracture of adhesive joints depends on elastic beam parameters describing the adherends and the applied loads. The basic specimen geometry was the cracked lap shear joint constructed of aluminium alloy with various adherend and bondline thicknesses. Loads were applied in different combinations of bending, tension and shear to generate a failure envelope for each adhesive and specimen geometry. It was found that crack propagation for precracked specimens occured at a critical strain energy release rate but was also a function of the G_I/G_II ratio and the bondline thickness. The experiments also showed that the loads required to propagate a crack in a precracked specimen were always lower than the loads required to break the fillet. Hence, by treating uncracked joints as being cracked, where the fictitious crack tip is assumed to coincide with the location of the fillet, a conservative estimate of the failure load is obtained.     

Shear Strength of Pressure Sensitive Adhesives and its Correlation to Mechanical Properties

Correlations between shear resistance and the mechanical properties of pressure sensitive adhesives are studied by measuring the deformation behaviour in the static and the dynamic shear test and determining the dynamic shear modulus of the adhesive. For polymers with low or moderate viscosities, the shear strain vs. time characteristics in a static shear test and, accordingly, the static shear strength, can be evaluated from the master curves of the dynamic shear modulus or the dynamic viscosity. The dynamic shear strength also can be calculated. These exact calculations cannot be applied to highly viscous or slightly crosslinked polymers. On the basis of the model experiments, empirical correlations between shear strength and the dynamic shear modulus are established which seem to be generally valid.     

纳米蒙脱土/环氧树脂胶粘剂制备工艺优化选择

介绍了制备纳米蒙脱土/环氧树脂胶粘剂的方法,并通过正交试验的方法分析了固化时间、固化温度、搅拌时间、搅拌温度对纳米蒙脱土/环氧树脂胶粘涂层拉伸剪切强度的影响,给出了上述四个工艺参数的最佳工艺规范并通过试验验证了结论。     

保护胶体稳定的丙烯酸酯乳液流变性

分别采用常规乳化剂和羟乙基纤维素为保护胶体制备丙烯酸酯乳液。通过TEM分别观察乳胶粒的形态。利用流变仪测定剪切速率（Ds）-剪切应力（τ）关系、剪切速率（Ds）-黏度（η）关系。结果表明：采用羟乙基纤维素为保护胶体制备的乳液与常规乳液具有不同结构，该结构使其乳液体系流变性能不同。在相同剪切速率下，保护胶体制备的丙烯酸酯乳液的剪切力明显大于常规乳液的剪切力，该乳液在一定剪切速率范围内有剪切稀化现象。     

Shear rate dependence of viscosity and first normal stress difference of LCP/PET blends at solid and molten states of LCP

The liquid crystalline polymer (LCP) and polyethylene terephthalate (PET) were blended in an elastic melt extruder to make samples having 20, 40, 60, 80, and 100 wt % of LCP. Morphology of these samples was studied using scanning electron microscopy. The steady state shear viscosity (η), dynamic complex viscosity (η*) and first normal stress difference (N₁) were evaluated and compared at two temperatures: 265°C, at which LCP was in solid state, and 285°C, at which LCP was in molten state. The PET was in molten state at both the temperatures. The shear viscosity of the studied blends displayed its dependence on composition and shear rate. A maxima was observed in viscosity versus composition plot corresponding to 80/20 LCP/PET blend. The N₁ increased with LCP loading in PET and with the increased asymmetry of LCP droplets. The N₁ also varied with the shear stress in two stages; the first stage demonstrated elastic deformation, whereas second stage displayed dominant plastic deformation of LCP droplets. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2212–2218, 2007     

考虑土体强度参数深度依赖性的非平稳随机场边坡滑动深度和体积分析

基于随机有限元方法（RFEM）和Monte-Carlo模拟,建立了能够模拟具有深度依赖性的土体强度参数边坡或具有软弱夹层边坡的非平稳随机场模型。通过辐射扫描方法获取最危险滑动面,得到非平稳随机场边坡滑动深度和滑动体积。将该方法与均质边坡和平稳随机场边坡获得的滑动深度和滑动体积进行对比,研究土体强度参数深度依赖性的非平稳随机场边坡的不同坡度和各向异性对滑动深度和滑动体积的影响。结果表明：基于RFEM的非平稳随机场滑动深度和滑动体积结果为地质灾害风险及后果评估提供了一个参考分析的新角度;参数的深度依赖性程度越高(变化率b越大),则边坡平均滑动深度和滑动体积越小;在大坡度滑坡风险后果评估中,可以基于均质边坡分析结果进行初步预估;在非平稳随机场中,随着各向异性的增大,所有坡度边坡的滑动体积变异系数增大;不同坡度下,水平方向的相关程度越大,则土坡内软弱夹层的不确定性越强,滑动体积的变异系数也不断增大。     

ESTIMATION OF EFFECTIVE SHEAR RATE FOR AERATED NON-NEWTONIAN LIQUIDS IN AIRLIFT BIOREACTOR”“

Effective shear rate is one of the indispensable parameters for the design of aerobic fermentors using a viscous non-Newtonian system. The estimation of effective shear rate in airlift loop bioreactors has been investigated with liquid circulation velocity. An empirical correlation of effective shear rate in airlift loop reactors is proposed.

γ_eπ= 3.26-3.51 ; 10²U_G + 1.48 10⁴U²_G

It is found that the effective shear rate is lower in airlift reactors than in bubble columns. This equation can be used for the cultivation of cells sensitive to shear stress.