Mapping surface temperature in large lakes with MODIS data

Satellite sensor MODIS on two platforms can produce Sea Surface Temperature over certain regions about three to four times per day. Our objective was to test if the MODIS SST product can be applied for lakes whose surface areas are large enough to be observed at the MODIS spatial resolution and to compare the satellite-derived lake surface temperatures with in situ measurements. Surface temperatures for Lakes Vänern and Vättern in Sweden, two of the largest European lakes, are extracted from the MODIS/Terra images for period 2001-2003. The results are analyzed on different quality levels, as all MODIS L2 products are equipped with an additional quality flag. We present temperature development over 2001-2003, and show the capability of the MODIS SST product to couple the known thermodynamical features in the lakes under study, where temperature varies greatly with space and time. These results can complement lake monitoring programs anywhere.     

大面积硅锂漂移探测器制备及其性能

制备了大面积硅锂漂移探测器,其性能为:探测器的灵敏面积123.6 cm~2;灵敏层深度2 mm;在室温和300 V反向偏压的工作条件下漏电流小于20 μA;对~(241)Am 5.486 MeV α粒子的能量分辨(FWHM)为77.67 keV。     

单液晶光阀彩色大屏幕投影显示

设计一电路,将彩色图象信息编码到黑白CRT的亮度之中,并将其写入液晶光阀,用白光读出,当编码合适时,读出的象颜色可与原图像一致。本文讨论了这一技术原理并进行了单液晶光阀彩色大屏幕投影的实验验证。     

十万立方米储罐用高强钢SPV490Q的冬季焊接施工

通过对高强钢焊接性能的分析 ,提出了高强钢冬季焊接施工带来的问题及处理办法。可靠的焊前预热和焊后保温是确保冬季焊接施工质量的关键措施     

大碎石柔性基层沥青性能分析

用沥青大碎石柔性基层对旧路面进行补强，可以有效地提高路面的使用性能，减少反射裂缝的产生，延长道路的使用寿命。对沥青大碎石柔性基层用加德士AH-70、SBS改性沥青和MAC改性沥青分别进行试验，通过试验结果和经济性能对比分析，找到适合此结构的最佳沥青。     

尼龙护套电线印字缺陷的分析及改进的措施

阐述了尼龙护套电线印字过程中,经常出现的几种缺陷,并对这些缺陷产生的原因进行了分析,尤其对印字拖印问题,进行了详细和深入的分析,并提出了一系列的改进措施。     

制氧(全)系统停车的迅速恢复和预防

介绍了安阳钢铁公司制氧厂结合实际总结出的制氧 (全 )系统停车的迅速恢复的操作方案和预防停车的措施 ;分析了经济效益。现机组自启动到送氧只需 2 3个小时 ,比设计值减少约 2 5小时。     

用C语言链表解决大整数运算的精度问题

介绍用C语言链表解决大整数运算的精度问题的方法。     

Defect formation in epitaxial oxide dielectric layers due to substrate surface relief

Defects were characterized in epitaxial (001) CeO₂ films deposited and planarizedin situ on patterned (001) LaAlO₃ substrates by ion beam assisted deposition (IBAD). A hill and valley structure with steps running parallel to the [100] LaAlO₃ axis was produced on the surface of the substrate by photolithography and ion beam etching prior to film deposition. A conformai epitaxial CeO₂ layer of ∼ 100 nm thickness was deposited on the heated substrate by e-beam evaporation. Lattice-matching between the e-beam film and the substrate was of the type: (001) CeO₂∥(001) LaAlO₃ and [110] CeO₂∥[100] LaAlO₃. Evaporative deposition of additional film onto the conformai layer was accompanied by bombardment with a 500 eV argon/oxygen ion beam to promotein situ planarization. Extreme lattice misfit for the orientation (001) CeO₂∥(001)LaAlO₃ and [001] CeO₂∥[001] LaAlO₃ caused formation of dislocations in the e-beam CeO₂ film in the vicinity of individual ledges in the substrate surface. Coherence of the CeO₂ film was locally lost in the step regions of the hill and valley structure. The large patterned steps, which are composed of numerous adjacent ledges in the LaAlO₃ surface, caused nucleation of CeO₂ with a tilt misalignment of up to ∼5‡ about the substrate [100]. Nucleation and growth of nonepitaxial CeO₂ crystallites was observed along the step regions of the film during the IBAD portion of deposition. Defect formation in the e-beam ceria layer due to substrate surface relief indicates that “lattice engineering≓ of multilayer epitaxial structures may not be possible when nonplanar surfaces are created during device fabrication. The IBAD CeO₂ layer was more defective than the conformai layer deposited without the impinging ion beam, even in the portions of the film where epitaxy was maintained throughout both layers.     

红外图像处理在墙体空鼓检测上的应用研究

提出了一种基于红外图像的建筑物墙体空鼓检测方法,不但可以远距离、无损地对建筑物空鼓等缺陷进行定性检测,还能对建筑物热工缺陷进行定量分析;采用一种红外图像处理方法来消除墙体温度分布中梯度干扰的影响;通过自适应地调整参数对红外图像进行图像增强处理,有效地排除了环境干扰;通过基于空鼓缺陷边缘轮廓的连通域计算,可直接得到空鼓面积的大小数据;建筑物缺陷现场检测实验结果表明,提出的检测方法既能快速定位出建筑物空鼓等缺陷位置又能以78.3%的精度检测出空鼓面积大小,具有较高的工程应用性。