改性聚酰亚胺在摩托车中的应用

本研究选择了改性聚酰亚胺、改性聚甲醛、改性尼龙三种材料应用于摩托车衬套制品,进行了对比试验,结果表明:采用改性聚酰亚胺的衬套具有强度高、耐磨损、尺寸稳定性好等特点,完全达到该产品设计的要求。     

耐深海压力容器的密封

用胶粘剂对耐深海压力容器进行密封，对各种浇注型密封胶配合不同的结构形式进行了一系列的试验，结果表明：用聚硫改性的环氧树脂密封胶能获得较好的密封效果，可达到耐40MPa水压密封。     

氧化还原引发降解天然橡胶与丙烯酸酯共聚的研究

研究了降解天然橡胶胶乳与丙烯酸甲酯、丙烯酸丁酯的聚合，以过氧化苯甲酰—N，N—三甲基苯胺(BP0—DMA)为氧化还原引发剂，考察了不同反应温度、引发剂配比、乳化剂用量及加料方式对单体转化率和接枝率的影响；用红外光谱对共聚物进行了表征。结果表明，采用乳化还原引发剂可使聚合反应低温快速进行，过量还原剂起阻聚作用，采用复合乳化剂可提高聚合反应速度和乳液稳定性，补加料可提高接技率。     

羧基偏氯乙烯丁苯胶乳粒子的相态结构和应用性能

以过硫酸铵为引发剂，十二烷基硫酸钠为乳化剂，采用种子聚合工艺，合成了偏氯乙烯质量分数为２３％～４３％的羧基偏氯乙烯丁苯胶乳。通过电镜观察到所合成的胶乳粒子具有核－壳结构。通过测定胶闰子表面层的羧基数量，研究了羧基的分布，结果表明，羧酸种类对羧基在胶乳粒子中及在聚合体系中的分布有重要影响，该胶乳作为地毯背衬粘合剂，具有粘合力高，极限氧指数高的特点，是一种较好的阻燃性粘合剂。     

Modified Indigo Method For Gaseous And Aqueous Ozone Analyses

The indigo method developed by Bader and Hoigné for aqueous ozone analysis was modified to allow for both gaseous and aqueous ozone determination. Gas or water samples were extracted with a gas-tight syringe containing a known volume of indigo reagent. The modified procedure provided a more consistent basis for gaseous and aqueous ozone determination allowing for more accurate ozone mass balance calculations. Direct gaseous ozone UV absorbance with molar absorptivity of 3,000 M^?1cm^?1 at 258 nm was used as primary standard to determine the molar absorptivity of the indigo reagent. The molar absorptivity of indigo reagent, assuming a 1:1 stoichiometric ratio for the reaction between indigo and ozone, was determined to be 23,150 ± 80 M^?1cm^?1, or approximately 16 percent higher than that of 20,000 M^?1cm^?1 suggested by Bader and Hoigné. An independently calibrated membrane-electrode ozone monitor showed good correlation with indigo method results using the molar absorptivity value determined in this study. The apparent molar absorptivity of aqueous ozone at the wavelength of 258 nm measured by the modified indigo method increased from 2,400 to 3,600 M^?1cm^?1 in the investigated ozone concentration range of 0.4 to 11.0 mg/L. This variation might have been caused by the inherent interference of unidentified ozone byproducts, which presence was supported with scanning spectra in the wavelength range of 200 to 300 nm.     

Influence of modified forms of urea and nitrogen levels on weed growth and grain yield of lowland rice

The growth of weeds and their subsequent reduction of rice yield as affected by N source neem cake coated urea (NCU), dicyandiamide coated urea (DCU), rock phosphate coated urea (RPCU), urea supergranules (USG) and prilled urea (PU) was studied on a clay loam soil at Coimbatore, India. Experiments were conducted in northeast monsoon (NEM) 1981, summer 1982, and southwest monsoon (SWM) 1982 seasons.The crop was associated with eleven weed species, and the dominant weeds wereEchinochloa crus-galli, Cyperus difformis andMarsilea quadrifolia. The weed flora varied between seasons. Deep placement of USG reduced the dry weight of weeds in NEM and summer seasons at 60, 90 and 120 Kg N ha^–1 whereas it increased the dry weight at 60 and 90 but not 120 Kg N ha^–1 in SWM season. The dry weight of weeds decreased with increased N rates for all N sources during NEM and summer seasons. In SWM season, dry weight of weeds increased with increased N rates for all N sources except USG. The grain yield of rice was drastically reduced with the deep placement of USG at 60 but not 120 Kg N ha^–1 in SWM season. The differential effect of the N sources between seasons was due to the change of the weed flora. Dominance ofE. crus-galli during SWM season had greater influence on weed dry weight and grain yield of rice.Nitrogen uptake by weeds was frequently greater in unfertilized plots, particularly in NEM and summer seasons. In SWM season, the apparent fertilizer N recovery by weeds was high for USG. It decreased from 53% for 60 Kg USG-N ha^–1 to 4% for 120 Kg USG-N ha^–1.Contribution from the part of Ph.D. work of the first author at Department of Agronomy, Tamil Nadu Agricultural University, Coimbatore-641 003, Tamil Nadu, India.     

基于带约束人工蜂群算法和平均Hausdorff距离的重力匹配方法

重力匹配算法是实现重力辅助惯性导航系统的关键技术之一。但是,传统重力匹配方法存在复杂度高、应用范围小等缺陷,一般很难实现精确、快速匹配的效果。将人工蜂群算法用于重力匹配的搜索过程,并将多普勒测速仪提供的速度信息作为限制条件对蜂群搜索过程进行约束。在此基础上,利用平均Hausdorff距离对匹配结果进行筛选,在重力数据库中重力异常精度一定的条件下,可降低误配率。仿真结果表明,该匹配算法在重力特征显著的区域具有较高的匹配率,可以达到精确、快速的匹配定位,从而实现重力辅助导航。     

Morphology and characterization of conductive films based on polyaniline‐coated polystyrene latexes

The polyaniline (PANI)‐coated polystyrene (PS) latexes were synthesized, and the electrically conductive films were prepared thereafter. The weight ratio of PANI was 5%. Thermal analysis of the latices was performed using DSC and TGA. In this study, the electrically conductive films were prepared above the PS glass transition temperature (T_g). During the film formation, the effects of the annealing temperature and atmosphere (air or N₂) on the film resistance were investigated. In addition, the film morphology was observed utilizing scanning electron microscopy. The film resistance decreased in the initial heating stage due to the increasing temperature and the compaction of film. Then the film resistance increased with further annealing due to the aging of PANI. Typically, the film resistance was about 6000 Ω/sq, and the conductivity was 0.3 S/cm. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5406–5413, 2006     

Determination of Both Mesopores and Macropores in Three-Dimensional Ordered Porous Materials by Nitrogen Adsorption

Three-dimensionally ordered silica structures containing both mesopores and macropores are created using polystyrene coacervate spheres with a diameter of ca. 146 nm. The close-packed polystyrene coacervate spheres are intercalated with tetraethyl orthosilicate. The spheres are removed by calcination leaving an inverse silica replica with a spherical macropore cavity diameter of 110 nm. Due to the nature of these porous structures, pores leading into the macropore cavity are in the mesopore regime, 40 nm in diameter. The nitrogen adsorption data described in the following paper gives a pore size for both the macropore cavity and the mesopore openings leading into the cavity. The pore sizes as determined by nitrogen sorption are in good agreement with the pore sizes observed by scanning electron microscopy. Mercury intrusion porosimetry results confirm the size of the mesopore openings leading into the macropore cavity, however due to destruction of the sample upon intrusion, extrusion results can not be obtained to determine main cavity diameters. As a result, nitrogen sorption may be a viable option for determining pore sizes with these three-dimensionally ordered materials containing both mesopores and macropores.