Whispering gallery modes in photoluminescence and Raman spectra of a spherical microcavity with CdTe quantum dots: anti-Stokes emission and interference effects

We have studied the photoluminescence and Raman spectra of a system consisting of a polystyrene latex microsphere coated by CdTe colloidal quantum dots. The cavity-induced enhancement of the Raman scattering allows the observation of Raman spectra from only a monolayer of CdTe quantum dots. Periodic structure with very narrow peaks in the photoluminescence spectra of a single microsphere was detected both in the Stokes and anti-Stokes spectral regions, arising from the coupling between the emission of quantum dots and spherical cavity modes.     

Quantitative determination of castor oil in edible and heat-abused oils by13C nuclear magnetic resonance spectroscopy

Application of¹³C nuclear magnetic resonance (NMR) spectroscopy for detection of castor oil (CO) in various edible oils, such as coconut oil, palm oil, groundnut oil and mustard oil, is described. Characteristic signals observed at δ 132.4, δ 125.6, δ 71.3, δ 36.8 and δ 35.4 ppm, due to C10, C9, C12, C13 and C11 carbons of ricinoleic acid (RA) in CO, were selected for distinguishing it from edible oils. Quantitative¹³C NMR spectra of oils were recorded in CDCl₃ with a gated decoupling technique. The minimum detection limits for qualitative and quantitative analyses were 2.0 and 3.0%, respectively. The proposed method is simple, nondestructive and requires no sample pretreatment. Its application to heat-abused oils has also been demonstrated successfully without any of the interferences observed in most other methods.     

Surface and Interfacial Studies of Plasma-Modified Composite Surfaces

Model epoxy and bismaleimide compounds in thin film form were used to simulate epoxy and bismaleimide composite surfaces, in order to study compositional changes and interfacial reactions induced by oxygen plasma treatment. X-ray photoelectron spectroscopy (XPS) and infrared reflection-absorption spectroscopy (IR-RAS) were used to probe chemical changes which occurred. XPS and IR-RAS were found to be complementary techniques in determining the nature of functional groups incorporated into surfaces by plasma treatment. IR-RAS analysis of the model surfaces following exposure to a liquid epoxy resin revealed that while adsorption of the liquid epoxy occurred on both plasma-treated and nonplasma-treated surfaces, the oxygen plasma-treated surface alone was capable of initiating ring-opening reactions in the epoxy. However, this effect was not observed unless immediate contact was made between the plasma-treated surface and the liquid epoxy resin, illustrating the short-lived reactivity of the functional groups on the plasma-treated surface.     

Softening and melting mechanisms of polyamides interfering with sliding stability under adhesive conditions

The thermal stability of polymers is a main issue when used as friction elements under dry sliding. Cast polyamide grades processed with either natrium or magnesium catalysors are slid on a small-scale and a large-scale test configuration to reveal the effect of softening or degradation on the sliding stability and to investigate possibilities for extrapolation of friction and wear rates between both testing scales. The combination of softening and afterwards transition into the glassy state is detrimental for the sliding stability of natrium catalysed polyamides, characterised by heavy noise during sliding. A transfer film formed under continuous softening also provides high friction. Melting during initial sliding is necessary for stabilisation in both friction and wear, and eventual softening of a molten film near the end of the test then not deteriorates the sliding stability. Softening of magnesium catalysed polyamides is favourable for the formation of a coherent transfer film resulting in more stable sliding than natrium catalysed polyamides. The differences in softening mechanisms of both polyamide grades is correlated to structural changes investigated by thermal analysis and Raman spectroscopy: the γ crystalline structure prevails in magnesium catalysed samples and the α crystalline structure is predominant in natrium catalysed samples. For internal oil lubricated polyamides, a time dependent degradation of the polyamide bulk deteriorates the supply of internal oil lubricant to the sliding interface, resulting in high friction and wear under overload conditions. As the degradation mechanisms during sliding are strongly correlated to the test set-up, extrapolation is only possible for friction in a limited application range, while wear rates cannot be extrapolated.     

Silicon‐containing heterocyclic polymers and thin films made therefrom

Thin films, in the range of tens of micrometers thickness, have been prepared by casting onto glass plates the chloroform or N‐methylpyrrolidone solutions of polyimides or poly(imide‐amide)s containing silicon and phenylquinoxaline units in the main chain. The polymers have been synthesized by solution polycondensation reaction of aromatic diamines having preformed phenylquinoxaline rings with bis(3,4‐dicarboxyphenyl)dimethylsilane dianhydride or with a diacid chloride resulting from the reaction of this dianhydride with p‐aminobenzoic acid. The polymers were easily soluble in polar aprotic solvents and showed high thermal stability. The free‐standing films exhibited good mechanical properties with tensile strengths in the range of 48–86 MPa, tensile modulus in the range of 1.25–2.22 GPa and elongation at break in the range of 3–37%. Electrical insulating properties of some polymer films were evaluated on the basis of dielectric constant and dielectric loss and their variation with frequency and temperature. The values of the dielectric constant at 10 kHz were in the range of 2.94–3.08 for polyimides and 3.89–4.49 for poly(imide‐amide)s. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3062–3068, 2006     

Electrochemical investigation of LiNi0.5Mn1.5O4 thin film intercalation electrodes

This work provides kinetic and transport parameters of Li-ion during its extraction/insertion into thin film LiNi_0.5Mn_1.5O₄ free of binder and conductive additive. Thin films of LiNi_0.5Mn_1.5O₄ (0.2 μm thick) were prepared on electronically conductive gold substrate utilizing the electrostatic spray deposition technique. High purity LiNi_0.5Mn_1.5O₄ thin film electrodes were observed with cyclic voltammetry, to exhibit very sharp peaks, high reversibility, and absence of the 4 V signal related to the Mn³⁺/Mn⁴⁺ redox couple. The electrode subjected to 100 CV cycles of charge/discharge delivered a capacity of 155 mAh g⁻¹ on the first cycle and sustained a good cycling behavior while retaining 91% of the initial capacity after 50 cycles. Kinetics and mass-transport of Li-ion extraction at LiNi_0.5Mn_1.5O₄ thin film electrode were investigated by means of electrochemical impedance spectroscopy. The apparent chemical diffusion coefficient (D_app) value determined from EIS measurements changed depending on the electrode potential in the range of 10⁻¹⁰-10⁻¹² cm² s⁻¹. The D_app profile shows two minimums at the potential values close to the peak potentials of the corresponding cyclic voltammogram.     

Characterisation of the adsorption sites of hydrogen on Pt/C fuel cell catalysts

A key component of a hydrogen fuel cell is a catalyst to dissociate dihydrogen to hydrogen atoms. In the present study, the adsorption of hydrogen on Pt/C fuel cell catalysts has been investigated by inelastic neutron scattering spectroscopy.

Monitoring a clean Pt(50%)/C catalyst with low energy neutron spectroscopy, after exposure to dihydrogen at 20 K, as it was heated to room temperature, showed three distinct temperature regimes: (i) a decrease in intensity from 10 to 60 K, (ii) a rise to a maximum between 60 and 120 K and then (iii) a slow fall-off towards room temperature. We assign the three regions as: (i) desorption of physisorbed dihydrogen, (ii) dissociation of dihydrogen to give an adsorbed layer and (iii) damping of the response by an increasing Debye–Waller factor.

The vibrational INS spectra of a series of Pt/C catalysts prepared under varying conditions were similar indicating that the same types of site are common to all the catalysts, although the relative proportions of each site are sample dependent. Features at 520, 950 and part of the intensity at 1300 cm⁻¹ are assigned to hydrogen on (1 1 1) faces, in good agreement with single crystal data. The mode at 640 cm⁻¹ is assigned as the doubly degenerate asymmetric stretch of Pt(1 0 0) faces with the symmetric stretch near 550 cm⁻¹.

We assign the bending mode of the on-top site to the feature at 470 cm⁻¹. The Pt–H stretch mode was observed at 2079 cm⁻¹. This is a significant result: this is the first time that hydrogen on the on-top sites has been observed on nanosized platinum particles supported on high surface area carbon black. The width of the INS peak is surprisingly large and may give additional information on the type and relative proportions of the crystallographic faces present on the catalyst particles.     

The effect of feedstock and process conditions on the synthesis of high purity CNTs from aromatic hydrocarbons

High purity multi-walled carbon nanotubes were synthesized from aromatic hydrocarbons (benzene, toluene, xylene and trimethyl benzene) using ferrocene as the source of Fe catalyst. Screening studies of aromatic feeds at 675 °C, residence time of 14 s and Fe/C atom ratio of 1.07%, resulted in feedstock carbon conversion of 20-31%, CNT yield of 19.8-30.5%, and catalyst yield of 5.3-8.3 (g CNT/g catalyst). While the quality of the CNTs as determined by TGA, SEM, TEM and Raman spectroscopy, were high and comparable for different feedstocks; their carbon conversion, CNT yield and catalyst yield differed noticeably. A process optimization study for toluene feed showed that carbon conversion of more than 39%, CNT yield of 38.7% and catalyst yield of 18.3 can be achieved at temperature of 800 °C, Fe/C atom ratio of 0.47%, and residence time of 10-20 s.     

Alumina-, niobia-, and niobia/alumina-supported NiMoS catalysts: Surface properties and activities in the hydrodesulfurization of thiophene and hydrodenitrogenation of 2,6-dimethylaniline

The activity of NiMoS catalysts supported on niobia, alumina, and niobia/alumina was compared for the thiophene hydrodesulfurization (HDS) and 2,6-dimethylaniline (2,6-DMA) hydrodenitrogenation (HDN) reactions. To evaluate the acidity of the supports and identify the nature of the sulfide sites, adsorption of 2,6-dimethylpyridine, pyridine, and CO was performed and followed by IR spectroscopy. This study has shown that with niobia as a support, the activity of NiMoS catalysts in thiophene HDS and in HDN of 2,6-DMA was no longer promoted by the synergy between Ni and Mo. The absence of synergy between molybdenum and nickel on niobia can be explained by the strong interaction of each metal with niobia at the expense of interaction with each other. Moreover, it has been shown that on a niobia/alumina support, the formation of the NiMoS phase can be directly linked to the presence of alumina not covered by niobia. However, niobia is an interesting support for the HDN of 2,6-DMA, because it favors the formation of xylene through direct ammonia elimination involving low H₂ consumption. The activity for xylene formation on niobia is linked to the electron-deficient nature of the Mo sulfide site, as demonstrated by CO adsorption followed by IR.