Mechanical and thermal properties of HVOF sprayed Ni based alloys with carbide

The objective of the present study is to develop multi-functioned coating to the components, which are made of copper with electroplated Ni and are widely used for steel making industry. In this paper, we report the mechanical and thermal properties of Ni based superalloys with carbide sprayed by high velocity oxygen fuel (HVOF), and the detailed effects of sprayed material, spraying conditions, and initial powder structure on these properties. It was found that, among commercial Ni self-fluxing alloys (without fusing treatment), coating with a carbon content of 0.58 mass% had the most preferable properties, with a good balance of the hardness, strength, and thermal shock resistance. The thermal shock resistance depended not only on the strength of the coating but also on the volume contraction when tested at high temperatures. For the several developed Ni based superalloys with carbide, Ni20Cr8Mo5Fe–WC and Ni16Cr15Mo3–WC demonstrated the prominent adhesion strength and thermal shock resistance with high Galvanic corrosion resistance through optimized spraying condition. Also, 20 mass% NiCr–Cr₃C₂ coating sprayed by using employed relatively small primary particle succeeded in achieving the multi-superior properties; high adhesion strength, high corrosion resistance and thermal shock resistance.     

Influence of load and speed on wear characteristics of grey cast iron in dry sliding — selection for minimum wear

The wear of grey cast iron in dry sliding conditions has been studied with the aims of (1) finding the influence of working conditions on the wear rate, and (2) determining the region of speed and load where low wear is accomplished. Grey cast iron with flake and nodular graphite was submitted to investigation using a pin-on-disc machine. The results indicate that the flake graphite cast iron is more suitable for applications at speeds greater than 4 m s⁻¹ and lower loads, while nodular cast iron has greater wear resistance at lower speeds in the range of loads investigated - from 50 N cm⁻² to 200 N cm⁻²     

一种提高地震速度解释精度的新方法

本以利用速度谱所伴生的叠加能量，采用二次曲线插值方法，寻找最大的叠加能量有所对应时间，然后利用叠加速度进行倾角校正，相位校正和最大炮检距校正，获取比较精确的层速度参数。     

轴对称问题线元上分布奇点的诱导速度势和诱导速度

本文给出轴对称问题线元上高次分布源和偶极在无界域中的诱导速度势和诱导速度的计算公式,可供用分布奇点法求解轴对称势流问题时参考.     

蒙特卡洛法速度谱的自动拾取

蒙特卡洛速度谱的自动拾取采用一种非线性优化的快速方法，所得叠加速度的精度可以满足常规地震资料处理中叠加的要求，转换为层速度后可用于叠前深度偏移成象，在给定初始速度模型前提下建立优化目标函数。采用蒙特卡洛非线性优化算法，以最大相似度量准则在考虑实际地质条件前提下给出速度约束条件，对初始速度模型加以扰动，自动寻找速度谱中叠加能量的全局最优解，从而获得合理的速度模型。实际地震资料处理的应用结果表明，自动拾取速度谱比常规的人工速度谱解释工作的效率大幅度提高。在SUN Ultra60机上,仅需1h即可完成2000km的地震资料的速度谱拾取任务，而且所获得的速度模型不受人为因素影响，转换所得的层速度模型用于叠前深度偏移后，获得了满意的成象效果。     

一种蒸发式冷凝器的新型设计方法

蒸发式冷凝器设计方法的粗糙和繁琐限制其广泛应用,特别是限制其应用于民用和小型商用建筑中。针对上述问题,作者通过实验研究了蒸发式冷凝器的影响因素（进风湿球温度、最小截面风速和喷淋水量）对蒸发式冷凝器热质交换的影响。同时提出了一种新型设计方法,此方法简单,精度较高。适合工程设计、选型和生产应用。     

生长条件对KDP晶体中散射颗粒的影响

利用透射电子显微技术对不同条件下生长的KDP晶体中包裹物进行了观察并测量了其相应尺寸。结果表明，晶体中的生长缺陷、pH值、生长速度和杂质与KDP晶体散射颗粒的形态存在密切关系。     

松潘-甘孜褶皱带的深部地壳构造特征及油气前景

四川松潘-甘孜褶皱带一直是地球科学家关注的一个焦点。近年来，石油地质学家也对它表现出了很大的兴趣。根据地震测深、重、磁、电等的探查，发现该褶皱带深部有一低速高导层，而对大火成岩省一峨眉玄武岩喷溢-地幔柱的认识深化均表明，四川松潘-甘孜褶皱带是可望获得油气勘探突破的靶区，重要的是断裂构造、圈闭、储集层的耦合与优化。     

郁江梯级水电站群联合优化调度初探

郁江梯级水电站群由西津、仙依滩和桂航3座水电厂组成。针对西津电厂出力变化频繁,加上西津下游两电厂装机容量较小,经常出现弃水,用增量动态规划法进行了联合优化调度探索,同时介绍马斯京根分段流量演算法。     

Influence of process variables on the drying of potato slices

Investigation of the effects of varying air velocity, slice thickness, and pre-treatment with sodium chloride solutions and surface active agents on drying potato slices indicated that the drying occurred entirely in the falling rate period and was controlled by the mechanism of liquid diffusion. The rate of drying, and therefore the diffusion coefficients, increased with the addition of sodium chloride and surface active agents. Diffusion coefficients were also influenced by air velocity and slice thickness, suggesting that the rate of drying of potato slices is controlled by a combination of internal and external resistances.