Homogenization of hardness distribution and distortion in high pressure gas quenching

Quenching with gases rather than oil or other liquid media has the advantages of reducing the risks concerning health and environment, while simultaneously homogenizing the quenching results and minimizing distortion due to a wide range of possible process parameter variations and the pure convective heat transfer. In this contribution, a coupled solution for increasing homogenization of quenching results within high pressure gas quenching will be presented. In the first stage, an experimental test facility was set up for flow investigations and in the second stage a numerical simulation model was generated. The numerical and experimental results of the flow through the chamber were compared for several boundary conditions. Finally, after complete verification of the simulation, the model may be used to assist in parameter variation for optimization of homogeneous high pressure gas quenching.     

Influence of wood extractives on the photo‐discoloration of wood surfaces exposed to artificial weathering

Extracted and unextracted black cherry (Prunus serotina), red oak (Quercus rubra), and red pine (Pinus resinosa) wood specimens were exposed to artificial weathering, and their discoloration process was investigated to obtain basic understanding on the role of wood extractives in the weathering of hardwoods and softwoods. Color measurements were made with a spectrometer according to ISO 2470 standards, using the CIELAB system. Results obtained showed that the rate of whiteness was not significantly affected by extractives removed with organic solvents, but were significantly affected when organic solvent extraction was followed by water extraction. The total discoloration rate had the same pattern, and chromaticity coordinates were less affected by wood extractives. These results confirm the hypothesis that some extractives contained in wood act as antioxidants and are able to provide some protection to wood surfaces against weathering degradation. However, more work is needed to understand the chemistry and mechanism of action of these extractives so as to develop any practical use for this property. © 2006 Wiley Periodicals, Inc. Col Res Appl, 31, 425–434, 2006; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.20248     

Cover Picture: Light‐Emitting Organic Solar Cells Based on a 3D Conjugated System with Internal Charge Transfer (Adv. Mater. 22/2006)

The cover image illustrates the dual photovoltaic and electroluminescence function of a single‐layer device based on a thienylenevinylene–triphenylamine with internal charge transfer (ICT), as reported by Cravino, Roncali, and co‐workers on p. 3033. The material forms an organic glass with isotropic electronic properties while ICT leads simultaneously to an extension of the photoresponse to the red and to an increase of the open circuit voltage. The use of an additional layer of C₆₀ further improves the photovoltaic. Images of the sun and moon courtesy NASA/JPL–Caltech.     

Effect of polymerization conditions on o‐phenylenediamine and o‐phenetidine oxidative copolymers

A series of new o‐phenylenediamine (OPD)/o‐phenetidine (PHT) copolymers with partly phenazine‐like structures has been successfully synthesized at three polymerization temperatures by chemically oxidative polymerization in four different polymerization media. The molecular structures and properties of the resulting OPD/PHT polymers were investigated by IR, UV–vis and high‐resolution ¹H NMR spectroscopies, and DSC, in order to ascertain the effect of reaction temperature, comonomer ratio and acid medium. The copolymerization mechanism of OPD with PHT monomers has been proposed. It is found that the statistical OPD/PHT copolymer obtained at a temperature of 118 °C has a higher degree of polymerization than that obtained at 12–17 °C. The OPD content in the copolymers calculated from NMR spectroscopic analysis is higher than that in the feed OPD content, whereas the OPD content calculated from element analysis is slightly lower than the feed OPD content. It can be predicted that denitrogenation takes place in the OPD units during the polymerization process at OPD/PHT molar ratios of 90/10 and 100/0. These OPD/PHT copolymers exhibit a much better solubility than the OPD homopolymer, hence suggesting an incorporation of PHT units into the phenazine structure of the homopolymer. The thermal behavior of the copolymers was also studied. Copyright © 2004 Society of Chemical Industry     

Effect of Plate Oscillation on Bubble Residence Time in an Aerated Stagnant Liquid

Gas transfer efficiency during absorption is an important factor in various technological processes involving the interaction between liquid and gaseous systems. It is known that gas bubble motion characteristics strongly affect the efficiency of mass transfer during gas absorption. A device for mechanical vibration of an aerated liquid was designed, based on a cylindrical column filled up with tab water and a plate oscillating in the vertical direction. The goal of the present study is to investigate the effect of vibration parameters such as amplitude, frequency and form of the applied signal on the efficiency of the oxygenation process. Bubble residence time in the liquid and bubble depth of submergence related to the oscillating plate surface were chosen as main parameters for measurements. Furthermore, experiments were conducted to study the effect of the design parameters of the vibrating plate on bubble motion characteristics. The resultant data show that bubble residence time and depth of submergence can be controlled by changing the amplitude, the frequency and the form of the vibration field applied.     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

A Study of AlN Films Prepared by Arc Ion Plating

Hexagonal AlN films have been obtained by arc ion plating at different negative biases ,X-ray diffraction and scanning electron microscopy results show that AlN films with smooth surfaces and (002) preferred orientation are obtained at low biases ,whereas those with coarse surfaces and (100) preferred orientation are obtained at high biases,The formation mechanism of AlN is analyzed and the experiment results are discussed,The effect of bias on adhesion strength has also been examined.