中国软磁铁氧体用氧化铁

介绍了中国软磁铁氧体用氧化铁的发展历史和现状，预测了未来的市场需求，并探讨了氧化铁的应用技术问题。     

Comparative hall measurements on wet- and dry-oxidized 4H-SiC MOSFETs

Hall measurements have been used to compare the properties of 4H-SiC inversion-mode MOSFETs with “wet” and “dry” gate oxides. While the field-effect mobilities were approximately 3–5 cm²/Vs, the Hall mobilities in 4H-SiC MOSFETs in the wet and dry oxide samples were approximately 70–80 cm²/Vs. The dry-oxidized metal oxide semiconductor field effect transistors (MOSFETs) had a higher transconductance, improved threshold voltage, improved subthreshold slope, and a higher inversion carrier concentration compared to the wet-oxidized MOSFETs. The difference in characteristics between the wet- and the dry-oxidized MOSFETs is attributed to the larger fixed oxide charge in the dry oxide sample and a higher interface trap density in the wet oxide sample.     

Al-P-Ti-Si-O催化剂上合成邻羟基苯乙醚

采用不均匀沉淀法制备了Al-P -Ti-Si-O催化剂 ,并研究了邻苯二酚与乙醇在该催化剂上的气相O -乙基化反应 ,考察了催化剂组成、反应温度、邻苯二酚 /乙醇摩尔比、进料速率对反应性能的影响 ,同时考察了催化剂的稳定性。结果表明 ,催化剂组成对反应性能有较大影响 ,在研究的范围内 ,四组分催化剂Al1 P1 3 0 Ti0 3 0 Si0 1 7显示出了较好的催化性能 ,当催化剂用量 1 4g、n(邻苯二酚 ) /n(乙醇 ) =1/5、进料速率 0 5ml/h ,反应温度 2 6 0℃时 ,邻苯二酚转化率和邻羟基苯乙醚收率分别可达到 91 5 %和 85 3% ,并在 10 0h内催化剂具有很好的稳定性     

对氧化物熔体浮区中重力对流的数值模拟

利用有限元分析方法数值模拟了界面形状对氧化物高温熔体碟形浮区中的温度分布和重力对流速率的影响，发现界面形状对重力对流速率有较大的影响，对于凸面，相对于炉圈平面5％的偏离使重力对流速率增大25％，偏离越大，重力对流速度越大，对于凹面，5％的偏离使重力对流速率减小15．7％，偏离越大，重力对流速度越小。     

Effect of oxygen flow rate on the structural and electrochemical properties of lithium nickel oxides synthesized by the sol–gel method

The structural and electrochemical properties of LiNiO₂ powders were investigated as a function of the oxygen flow rate employed in the preparation of lithium nickel oxide. It was found that oxygen played an important role in the synthesis of highly crystallized LiNiO₂(R3¯m). In the crystallization process of LiNiO₂, a deficiency of oxygen in the calcination reactor induced the formation of impurities and cubic rock-salt structure (Fm3m) in LiNiO₂ powders. For LiNiO₂ prepared at higher oxygen flow rates, the electrode delivered high discharge capacities with relatively good retention rates. But very low electrode capacity was obtained from LiNiO₂ prepared at lower oxygen flow rates.     

Influence of heat transfer on anodic oxidation of aluminium

The influence of convective heat transfer on constant current density anodizing of aluminium in sulfuric acid has been examined in a wall-jet electrode reactor. The uniformity of the anodic film thickness is related to the local electrode temperature distribution, which is dependent on the convection. The higher the local temperature, the greater the local oxide thickness. An increased local temperature enhances local field assisted oxide dissolution at the pore bases, and consequently acts to increase the local current density. At relatively high current densities, local features develop on the electrode surface, accompanied by high initial, local temperature rises. The relevance of such local features, limiting useful oxide growth, is considered further.     

Rich photoluminescence emission of SnO2–SiO2 composite aerogels prepared with a co-fed precursor sol–gel process

Tin oxide–silica composite aerogels were successfully prepared with a co-fed precursor sol–gel process. The crystallinity of the tin oxide nanoparticles, embedded in the mesoporous SiO₂ network, was improved with increasing the post-reaction thermal treatment temperature. The composite aerogels exhibited a rich photoluminescence (PL) emission contributed by both SnO₂ and SiO₂. The PL peak of 346 nm was from the near band edge emission of the tin oxide nanoparticles, and the ones located at 310 and 476 nm were attributable to the oxygen deficiencies of the silica network. Three more emission peaks, 387, 432, and 522 nm, were observed, with the 387 nm peak contributed by the oxygen vacancies V_O⁺⁺, the 432 nm peak by the Sn interstitials, and the 522 nm peak by the oxygen vacancies V_O⁺, respectively, of the tin oxide nanoparticles. The intensities of these three defect level emissions were found decreased, as compared to that of the near band edge emission, with increasing the post-reaction thermal treatment temperature as the tin oxide crystallinity improved.     

Catalytic steam reforming of methane over La0.8Sr0.2CrO3 based Ru catalysts

La_0.8Sr_0.2CrO₃ based Ru catalysts were studied as potential new anodic materials for Solid Oxide Fuel Cells directly fed with methane and operating at intermediate temperature under water deficient conditions. Two kinds of materials very close in composition were obtained following two different preparation procedures. Catalyst samples were characterized by physicochemical methods (XRD, SEM, BET and Chemical Analysis) and studied in methane steam reforming under water deficient conditions. Carbon formation during catalytic testing was studied by temperature programmed oxidation (TPO). Both types of catalysts were found very active and resistant to carbon formation. The unusual oscillatory behavior of the catalytic activity observed for one type of catalyst was discussed.     

Sol-gel processing: A versatile concept for special glasses and ceramics

The various parameters related to sol-gel processing are discussed with special reference to those which usually attract less attention but depending on the final product in mind, can play important roles. The versatility of the sol-gel technique in materials preparation is demonstrated by discussing the various products developed at the author’s laboratory by using this processing method.     

A detailed analysis of ambipolar diffusion in nanostructured metal oxide films

In this paper a transport equation is derived which describes the behaviour of the nanostructured metal oxide films in a photoelectrochemical cell. It is shown that a detailed analysis of the charge compensation mechanism necessarily leads to a transport equation with characteristics similar to but logically distinct from the pure diffusion equation. The studied phenomenon was named ambipolar diffusion in the early 1950s. It takes into account the fact that the diffusion processes of ions and electrons occur at different speeds. A weak electric field therefore couples the processes together to preserve charge neutrality. The electric field in turn affects the transport resulting in a deviation from purely diffusive behaviour. However, this has not been widely recognised in the literature for nanostructured semiconductor films until very recently. In this paper a detailed analysis is presented. It is based on the assumption that the current density is solenoidal. It is shown that application of the ambipolar diffusion model to a photoelectrochemical cell based on a nanostructured metal oxide film leads to an additional term in the transport equation, rather than only a new diffusion coefficient as in earlier work. It is also shown that the boundary conditions interact closely with the equation to form a transport model.