Effect of vapour phase hydrogen peroxide,as a decontaminant for civil aviation applications,on microstructure,tensile properties and corrosion resistance of 2024 and 7075 age hardenable aluminium alloys and 304 austenitic stainless steel

Abstract

A response to the chemical or biological contamination of aircraft requires the use of a suitable decontaminant. Among possible chemical decontaminants, vapour phase hydrogen peroxide appears to be a likely candidate in terms of a combination of efficacy, low environmental impact and potential for materials compatibility. The present paper examines the effect of hydrogen peroxide, both in the vapour phase and as a liquid concentrate on two common structural materials used in aviation, namely 2024 and 7075 age hardenable aluminium alloys and on 304 austenitic stainless steel, the latter as employed in galley and lavatory surfaces. The present paper characterises both the effects of hydrogen peroxide on the microstructure of the materials and the impact that decontamination has on the tensile properties and corrosion resistance of these materials. Microstructural effects are both relatively small in magnitude and confined to a region immediately beside the exposed surface. No systematic effect is found on either the tensile properties or the post-exposure corrosion resistance of the three alloys examined. These observations are encouraging in terms of the use of vapour phase hydrogen peroxide for decontamination applications.     

Evolution of textures in hot rolled Nb - Ti and V - Nb microalloyed steels

Abstract

A considerable texture gradient in the through thickness direction was observed during hot rolling of Nb - Ti and V - Nb microalloyed steels. The most intense deformation texture for Nb- Ti steels was {113}〈110〉 at all depths, whereas for V - Nb steels the plane was shifted to {115}〈110〉 ; the angular difference between {113} and {115} is about a degree. The recrystallisation texture of austenite, {100}〈001〉 , transformed into {100} 〈011〉 component in the ferrite and indicated an increase in the intensity with increase in depth for both Nb - Ti and V - Nb steels. However, the intensity of this {100}〈011〉 texture was less for Nb - Ti steels compared to V - Nb steels at all depths. The reduced intensity of {100}〈011〉 texture in Nb -Ti steels is likely to be the reason for the superior formability and improved toughness of Nb - Ti steels as compared with V - Nb steels. The {100}〈011〉 type of texture has an undesirable effect on the edge formability of steels.     

Serrated yielding in Cu-1 wt-%Cd alloy

Abstract

The influence of grain size and temperature on the serration patterns of the Portevin-Le Chatelier (PLC) effect and on the yield and flow stresses in a Cu-1 wt-%Cd alloy was investigated in the temperature range 150 to 360 ° C. Two kinds of serration patterns were observed in this alloy. Type I occurred at lower temperatures and its yield points are moderately spaced. Type II consists of regular jerky flow observed athigher temperatures. The Hall-Petch equation is obeyed over the temperature range in which jerky flow occurs. The Hall-Petch parameter k (?) is observed to show a local maximum in the temperature range where serrated flow is first observed. The PLC effect is associated with the solute- dislocation interactions, implying that k (?) contains a component associated with grain size dependent dislocation storage.     

Effect of heat treatment on tensile properties of friction stir welded joints of 2219-T6 aluminium alloy

Abstract

The effect of post-weld heat treatment (PWHT) on the tensile properties of friction stir welded (FSW) joints of 2219-T6 aluminium alloy was investigated. The PWHT was carried out at aging temperature of 165°C for 18 h. The mechanical properties of the joints were evaluated using tensile tests. The experimental results indicate that the PWHT significantly influences the tensile properties of the FSW joints. After the heat treatment, the tensile strength of the joints increases and the elongation at fracture of the joints decreases. The maximum tensile strength of the joints is equivalent to 89% of that of the base material. The fracture location characteristics of the heat treated joints are similar to those of the as welded joints. The defect free joints fracture in the heat affected zone on the retreating side and the joints with a void defect fracture in the weld zone on the advancing side. All of the experimental results can be explained by the hardness profiles and welding defects in the joints.     

Ultrahigh strength hot rolled microalloyed steel: microstructure and properties

Abstract

A low carbon steel alloyed with Ni, Mn, Mo, Cu and microalloyed with Nb and Ti was prepared. Continuous cooling transformation behaviour of the steel was evaluated. Formation of polygonal or Widmanstätten ferrite is suppressed at high temperature and the 'C' curve is shifted to an extreme right. At lower temperatures a flat top 'C' curve with a mixed structure of bainite and martensite was obtained and the transformation temperatures do not vary much with a wide range of cooling rates. The steel was thermomechanically processed at different finishing temperatures and ultrahigh strength values were obtained as a result of austenite grain refinement, highly dislocated fine lath martensite structure along with tiny precipitates of microalloying carbide and carbonitride at all finish rolling temperatures. The stable and large TiN/TiCN particles formed during casting have impaired the impact toughness values at ambient and at ?40°C temperatures.     

Compressive behaviour of open cell Al–Al2O3 composite foams fabricated by sintering and dissolution process

Abstract

The sintering and dissolution process (SDP) was used to produce the fine open cell Al–Al₂O₃ composite and pure Al foams with the relative density of 0·25–0·40 and the pore size of 112–400 μm. The composite foam exhibited much higher yield strength and Young's modulus than the pure Al foam, and thus had an elevated plateau stress. Moreover, the composite foam showed a unique dependence of the compression stress on the pore size, i.e. it increased with increasing pore size, which was quite different from that for the common metal foams.     

Plasticity induced transformation in a metastable β Ti-1023 alloy by controlled heat treatments

Abstract

Investigations into the possibility of improving the strength–ductility relation in a metastable β-titanium alloy (Ti–10V–2Fe–3Al) through plasticity induced transformation (PiTTi) have been carried out. Various heat treatments in the β and/or α+β condition were performed to study their influence on both the microstructure and solute partitioning, which eventually control the PiTTi effect. Stress induced martensite formation promoting such effect has been observed upon compression testing for β and β+(α+β) microstructures. The stress–strain curves exhibiting stress induced martensite show a ～20% increase in strength, while still retaining a reasonable ductility level. Microstructural parameters such as grain size and solute concentration (especially V) in β have been related to the alloy's ability to exhibit PiTTi.     

Effect of local volume fraction of microporosity on tensile properties in Al–Si–Mg cast alloy

Abstract

Porosity in Al–Si–Mg cast alloys utilised in automotive parts affects directly products quality, i.e. mechanical properties. In this study, the effect of micropores on mechanical properties has been investigated by X-ray tomography from the viewpoint of clustering micropores. The local volume fraction (LVF) of porosity was introduced to analyse the effect of clustering micropores. The statistical Weibull method was also used in order to explain strength of the alloy tested. The fracture strain decreased drastically from 17 to 3% on an inverse parabolic relationship with increasing porosity. In the case of the specimens that contain the largest pore higher than 100 m m, the ultimate tensile strength decreases monotonically. It is found that the fracture surface passes through high LVF regions. The fracture strain obviously depends on the ratio of LVF higher than 10%. It is confirmed that the LVF, which represents unevenly distribution of micropores cluster, is one of important dominant factor for managing the mechanical properties in the Al–Si–Mg cast alloy.     

Dielectric properties in GHz range of porous Si3N4–BN–SiO2 ceramics with considerable flexural strength prepared by low temperature sintering in air

Abstract

Porous Si₃N₄–BN–SiO₂ ceramics with ultimate apparent porosities between 0·140 and 0·799 were fabricated in air at 1100°C by partial sintering using core starch as both consolidator and pore former in the green bodies. The pores were derived from burning off the starch, the partial oxidation of silicon nitride and the stack of particles of the start materials. Effect of retaining time on the microstructure of sintering bodies was analysed by SEM analysis. Reference intensity ratio (RIR) technique based on the X-ray diffractometry results demonstrated the phase components content of sintered bodies. Influence of porosity on the flexural strength of porous Si₃N₄–BN–SiO₂ ceramics was investigated. The ceramic with a porosity of 0·140 attained a maximal flexural strength of 60±4·11 MPa. In addition, the dielectric constants and loss tangents were presented for porous Si₃N₄–BN–SiO₂ triphase ceramics in the frequency range of 18–40 GHz, and the real part of dielectric constant of the materials reached as low as 2·67 at the porosity of 0·732 at a frequency of 20 GHz.     

The life of a plant builder in the modern metals industry

Abstract

The 2007 SMEA Celebrity Lecture (Sheffield Metallurgical and Engineering Association) was given by Roy Tazzyman, the outgoing Managing Director of Siemens VAI–UK, on 4 July 2007 at the University of Sheffield, in conjunction with the Association's annual conference. Ken Ridal summarises the proceedings.