Total simulation model of the thermo-mechanical process in shape rolling of steel rods

The production of steel reinforcing bars for civil engineering is investigated by means of FEM-simulation. An integrated system for computing appropriate thermo-mechanical parameters of the rolling process is proposed. Generalized plane strain approach and coupled thermal-mechanical solution are applied. The microstructural model combines both the effect of the recrystallization mechanisms (static, dynamic and metadynamic) upon the austenite grain forming in hot rolling and that of phase transformation upon the final microstructure. The phases are created during interrupted below the temperature of martensite transition cooling. Thus a typical industrial process for thermo-mechanical strengthening of reinforcing bars, known as Tempcor-process is considered. Computational results are validated to experimental measured mechanical properties of the steel. By means of computer simulation the system can perform different solutions, giving the possibility to obtain a reasonable choice of different thermo-mechanical rolling conditions.     

加氢处理润滑油基础油各组分对光安定性的影响

将经紫外光照前后的加氢处理润滑油基础油分离为饱和烃、轻质芳烃、中质芳烃、重质芳烃和极性组分，分别采用薄层色谱、质谱和紫外吸收光谱分析了各组分的烃组成、硫和氮含量的变化，并通过将从原料油中分离出的各组分反加到光安定性好的饱和烃中，试验验证了加氢处理润滑油基础油中的重质芳烃和极性组分是光不安定组分，其中含有硫、氮的芳香杂环化合物光安定性差。     

Experimental Research on Erbium-doped Superfluorescent Fiber Source

The effects of the variations in fiber length, fiber mirror reflectance on efficiency and output power are experimentally investigated for erbium-doped double pass backward superfluorescent fiber sources (SFSs). The influence of fiber length on mean wavelength stability (MWS) has also been demonstrated. By incorporating a short section of un-pumped erbium-doped fiber (EDF) at the output port, the pump power dependent on MWS becomes independent of pumped EDF length. This is a novel phenomenon that hasn‘t been reported up to now,and should be helpful to SFS fabrication and theory analysis. By using a fiber Michelson interferometer as spectrum slicing component,a multi-wavelength fiber source (MWFS) with ～20 channels (from 1542nm to 1559nm) is got. The MWFS has a channel spacing of ～0. 8 nm which satisfies ITUstandard. The intensity fluctuation among channels is less than 0.5dB,and the extinction ratio of all channels is above 14dB. This kind of MWFS should be useful to wavelength division multiplexing systems.     

Numerical analysis of two-dimensional steady-state and transient heat transfer in a parallel duct filled with pressurized He II

Analysis on steady-state and transient heat transfer on a flat plate at the middle of a parallel duct immersed in He II was performed for bath temperatures from 1.8 to 2.1 K at 101.3 kPa. Two-dimensional computer code named SUPER-2D developed by the authors based on the two-fluid model and the theory of mutual friction was used. Steady-state critical heat flux (CHF) and the time lag from the application of a step heat input to λ transition, that is called a lifetime, were obtained numerically for various step heat fluxes and for the channel gaps from 2 to 20 mm. Effect of the gap restriction on the CHF and the lifetime were clarified. The solutions were compared with the experimental data for the ducts with the same structures and the corresponding conditions. They agreed well with the experimental data. The heat transport mechanism in the parallel duct was clarified.     

Robust State Feedback Control Through Actuators With Generalized Sector Nonlinearities And Saturation

In control systems, actuators often have nonlinear characteristics that can not be neglected. For linear systems driven by actuators satisfying the generalized sector condition, a robust state feedback controller synthesis method is proposed to achieve the ultimate boundedness control. The method is based on the linear matrix inequality approach and is easy to apply. As an important special case of the generalized sector condition, the saturation characteristic of actuators is discussed separately, and non‐conservative results are obtained.     

中子辐照金刚石生成卡宾碳

金刚石在中子辐照下发生相转变,得到了线性结构的卡宾碳。所得产物为覆盖金刚石表面的黑色薄膜状物质,其拉曼光谱在2191cm-1处有强峰,归属于C≡C伸缩振动;同时,其俄歇电子谱的峰位与金刚石相比有5eV的位移,证实了卡宾碳的存在。在中子辐照条件下,金刚石向卡宾碳的转化可能是通过碳原子堆垛形式发生变化而实现的。     

岭澳核电工程38m平台边坡处理

岭澳核电重件道路施工中所遇到的38m的观景平台在大亚湾核电站占有重要地位,在工程施工中发现边坡坡体陡峭,无法达到规范规定的稳定要求,故采取了加固措施。采用抗滑稳定计算的分析方法,对边坡加固的必要性及实施加固后的稳定性进行了分析。     

八种新功能晶体的比热及其与相变掺杂物关系的实验研究

本文对八种新型功能晶体Ｌｉ２Ｂ４Ｏ７、Ｂｉ１２ＴｉＯ２０、Ｂｉ１２ＧｅＯ２０、Ｂｉ１２ＧｅＯ２０、Ｂｉ４Ｇｅ３Ｏ１２、Ｓｒ１－ｘＢａｘＮｂ２Ｏ６（ｘ＝０．３３，０．４８）、ＬｉＴａＯ３等在１３０～９７３Ｋ范围内的比热行为及其与相变、组分之间的关系进行了实验研究，给出了比热的多项式拟合方程，并与用纽曼－卡普定律及用Ｗｉｋｅｌｍａｎｎ经验方程的比热计算值作了对比，为晶体比热的估算提供了依据和方法。