CALCULATION ON TWO-PHASE FLOW TRANSIENTS AND THEIR EXPERIMENTAL RESEARCH

From basic equations of gas-liquid, solid-liquid, solid-gas two-phase flow, the calculating method on flow transients of two-phase flow is developed by means of characteristic method. As one example, a gas-liquid flow transient is calculated and it agrees well with the experimental result. It is shown that the method is satisfactory for engineering demand.     

LS SIMD微处理器中的三组指令并发执行的设计

文章介绍了LS SIMD微处理器中实现三组指令并发执行的可能性和必要性，分析了三组指令并发执行给流水线带来的影响，并讨论了控制逻辑对三级指令并发执行的控制及其实现形式。     

数字式液压逻辑流量阀的设计

数字工流量阀采用数字控制方式，调节系统流量以达到液压系统调整目的，它本身具有控制响应快、精度高、稳定性好、适应范围大等优点，在行走机械上将会得到广泛地应用。     

Influence of Coherent Flow Structures on the Dynamics of Suspended Sediment Transport in Open-Channel Flow

The influence of suspended sediments on coherent flow structures has been studied by simultaneously measuring the longitudinal and vertical components of the instantaneous velocity vector and the instantaneous suspended particle concentration with an acoustic particle flux profiler. The measurements were carried out in clear water and in particle-laden open-channel flows. In both cases, they clearly show the predominance of ejection and sweep phases that are part of a burst cycle. The analysis further demonstrates the importance of the ejection and sweep phases in sediment resuspension and transport. Ejections pick up the sediment at the bed and carry it up through the water column close to the surface. It is shown that ejections and sweeps are in near equality in the near-bottom layer, whereas ejections clearly dominate in the remaining water column. The implications of these results for sediment transport dynamics are discussed.     

PROGRESS IN THE MODELLING OF AIR FLOW PATTERNS IN TIMBER KILNS

Progress in modelling air flow patterns in timber kilns using Computational Fluid Dynamics is reviewed in this work. These simulations are intended to predict the distribution of the flow in the fillet spaces between boards in a hydraulic model of a timber kiln. Here, the flow regime between the boards is transitional between laminar and turbulent flow, with Reynolds numbers of the order of 5000. Running the simulation as a transient calculation has shown few problems with convergence issues, reaching a mass residual of 0.2% of the total inflow after 40-100 iterations per time step for time steps of 0.01 s. Grid sensitivity studies have shown that non-uniform grids are necessary because of the sudden changes in flow cross section, and the flow simulations are insensitive to grid refinement for non-uniform grids with more than 300,000 cells. The best agreement between the experimentally-measured flow distributions between fillet spaces and those predicted by the simulation have been achieved for (effective) bulk viscosities between the laminar viscosity for water and ten times that value. This change in viscosity is not very large (less than an order of magnitude), given that effective turbulent viscosities are typically several orders of magnitude greater than laminar ones. This result is consistent with the transitional flows here.     

Magnetic Resonance Visualisation of Flow and Pore Structure in Packed Beds with Low Aspect Ratio

Different NMR techniques were combined to obtain the structure and velocity information for a systematic investigation of fixed beds with low aspect ratio (tube diameter to particle diamter, d_t/d_p) in the range 1.4 to 32. The structure of the void space was determined for a variety of packed beds of glass beads or regular and irregular porous pellets by magnetic resonance imaging (MRI). Based on the images the radial distribution of the voids within the bed was obtained. Ordering effects were found even for non‐spherical and polydisperse particles, and a maximum of the fluid density near the tube wall was confirmed for all pellet geometries and sizes. By combining MRI with velocity encoding, velocity profiles and distributions of flow velocity components of a single fluid phase through packed beds have been acquired. The radial velocity distribution follows an oscillatory pattern which largely reflects the ordering of the particles, which can be accessed from the density distribution of the interparticle fluid. Maximum velocities of up to four times the average value were found to occur near the tube wall. This wall effect was observed for all but the smallest particles, where the aspect ratio was d_t/d_p = 32. Moreover, a visualisation of flow pattern in the presence of packed particles was achieved by using a tagging technique, and the stationary flow field could be identified for an experimental time of several hours.     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

Lipid damage in farmed rainbow trout (Oncorhynchus mykiss) after slaughtering and chilled storage

The flow ice system including ozone (OFI condition) was tested for slaughtering and storage (up to 16 days) of farmed rainbow trout (Oncorhynchus mykiss). Lipid damage analyses were carried out and compared to sensory acceptance and instrumental colour changes. Comparison to individuals processed with the flow ice system in the absence of ozone (FI condition) was undertaken. Rainbow trout slaughtered and chilled under FI and OFI conditions showed a low lipid damage development, according to lipid oxidation and hydrolysis events and lipid composition (polyunsaturated fatty acids, phospholipids and endogenous antioxidants) changes. Additionally, both icing conditions led to largely good quality and shelf life times and to the absence of changes in colour properties. It is concluded that flow ice as such, or including the presence of ozone, can be considered as ideal strategy to be employed as slaughtering and storage system during the commercialisation of the actual farmed species. The ozone presence has shown some profitable effects as leading to an extended shelf life time by quality retention of several sensory parameters; in contrast, some negligible negative effects could be observed on the secondary and tertiary lipid oxidation development. However, the oxidation values reached by individuals kept under OFI conditions cannot be considered as particularly high.     

Numerical characterization of a microscale solid-oxide fuel cell

In this study, a single unit of planar micro-solid-oxide fuel cell (μSOFC) is investigated numerically to evaluate the influences of flow channel design, oxygen composition, and thermal operating conditions on cell performance. Four flow channel designs are examined under the co-flow configuration: serpentine, double serpentine, rod bundle, and oblique rib. For all designs, the contacts areas of interconnect to electrodes are kept consistent to maintain the ohmic losses at the same level. To characterize the mass transport effects, there are three different compositions, 100% O₂, 50% O₂/50% N₂ and air, fed to the cathode inlet. Different thermal conditions, adiabatic and isothermal, are applied to the outer boundary of the μSOFC and the results are compared. The outcomes suggest that both thermal conditions and oxidant composition show remarkable influences on μSOFC performance. Under adiabatic conditions, the rise of cell temperature causes a decrease in reversible voltage, deteriorating the overall cell competence. When oxygen is diluted with nitrogen, local gas diffusion becomes dominant to the cathode reaction. Bulk flow, on the other hand, plays a minor role in cell performance since there is little deviation in the polarization curves for all flow channel designs, even at high current densities. For comparison, the flow visualization technique is employed to observe the transport phenomena in various flow channel designs. The flow patterns are found to resemble the concentration distribution, providing a useful tool to design μSOFCs.     

组合式光纤流量传感器

提出了一种新型的组合式光纤流量传感器，介绍了它的工作原理，详细讨论了光脉冲转换器的设计要点，据此设计了传感头，并给出了它的实验结果。