Simultaneous process optimization and heat integration based on rigorous process simulations

This paper introduces a simultaneous process optimization and heat integration approach, which can be used directly with the rigorous models in process simulators. In this approach, the overall process is optimized utilizing external derivative-free optimizers, which interact directly with the process simulation. The heat integration subproblem is formulated as an LP model and solved simultaneously during optimization of the flowsheet to update the minimum utility and heat exchanger area targets. A piecewise linear approximation for the composite curve is applied to obtain more accurate heat integration results. This paper describes the application of this simultaneous approach for three cases: a recycle process, a separation process and a power plant with carbon capture. Case study results indicate that this simultaneous approach is relatively easy to implement and achieves higher profit and lower operating cost and, in the case of the power plant example, higher net efficiency than the sequential approach.     

Angiotensin I‐converting enzyme inhibitory and Ca‐binding activities of peptides prepared from tuna cooking juice and spleen proteases

Tuna cooking juice is a by‐product from the tuna canning industry. In this study, tuna cooking juice was hydrolysed by proteases extracted from the spleen. Tuna cooking juice showed the highest ACE inhibitory and Ca‐binding activities after hydrolysis for 270 and 180 min, respectively. The hydrolysate was further fractionated by ultrafiltration. The permeate exhibited highest ACE inhibitory and Ca‐binding activities when passed through 1 and 5 kDa cut‐off membranes, respectively. Gel filtration chromatography was used to determine the MW of bioactive peptides that exhibited highest ACE inhibitory and Ca‐binding activities. Those peptides that exhibited highest ACE inhibitory and Ca‐binding activities were the MW range of 238–829 Da and 1355–1880 Da, respectively. These results suggest that the tuna cooking juice and the spleen protease extract are a potential source of bioactive peptides that can be utilised as bioactive ingredients in functional food and nutraceuticals.     

Cheese fortification using saturated monoglyceride self‐assembly structures as carrier of omega‐3 fatty acids

The purpose of this research was to study the capacity of emulsions containing saturated monoglyceride self‐assembly structures to deliver omega‐3 fatty acids in fresh soft cheese. To this aim, fortified emulsions containing different ratios of milk, saturated monoglycerides (MGs) and cod liver oil were added to milk before cheese‐making. These emulsions were characterised by distinct microstructural features observed by polarised light microscopy and apparent viscosity values. The omega‐3 delivery performance of MG emulsions highlighted that this strategy allowed a good retention of the omega‐3‐rich oil in the curd (up to 75%). The fortified cheeses showed yield value and fat content higher than those of control samples. The enriched cheese showed hardness and cohesiveness obtained by texture profile analysis similar to those of the unfortified product. Only a slight decrease in gumminess was detected in fortified cheese.     

Characteristics and formation mechanism of porosities in CFRP during laser joining of CFRP and steel

An experimental investigation on the mechanism of porosity formation during the laser joining of carbon fiber reinforced polymer (CFRP) and steel is presented. The porosity morphology and distribution were characterized by optical and scanning electron microscopy, and the thermal pyrolysis behaviors were investigated by thermal analysis and designed back-side cooling experiments. The results show that there are two types of porosities in CFRP. Porosity I only appears when the heat input is more than 77.8 J/mm. It has a smooth inner wall and distributes near the bonding interface between CFRP and steel at the central area of melted zone, which is caused by gaseous products such as CO₂, NH₃, H₂O, and hydrocarbons produced by the pyrolysis of CFRP. Porosity II can be seen under all joining conditions. It has a rough inner wall and distributes far away from the bonding interface, concentrating at the final solidification locations. Porosity II is caused by the shrinkage of melted CFRP during solidification stage.     

Fundamental Evaluation of Power Supply and Rectifiers for Wireless Power Transfer Using Magnetic Resonant Coupling

This paper provides a fundamental analysis of a power supply and rectifiers for wireless power transfer using magnetic resonant coupling (MRC). MRC enables efficient wireless power transfer over middle‐range transfer distances. MRC for wireless power transfer should operate at a high frequency in the industry science medical band, such as 13.56 MHz, because the size of the transfer device decreases at higher transfer frequencies. Therefore, the output frequency of the power supply on the transmitting side should be 13.56 MHz. In addition, the rectifier on the receiving side is operated at a high frequency. This paper focuses on the reflected power in the power supply and rectifiers. Thus, the parametric design method is clarified for the power supply, including a low‐pass filter to match the output, the impedance of the power supply with the characteristic impedance of the transmission line. In addition, the effects on the rectifiers of silicon carbide and gallium nitride diodes are confirmed by performing an experiment and a loss analysis.     

Hydrocarbon-based electrode ionomer for proton exchange membrane fuel cells

The electrode ionomer is a key factor that significantly affects the catalyst layer morphology and fuel cell performance. Herein, sulfonated poly(arylene ether sulfone)-based electrode ionomers with polymers of various molecular weights and alcohol/water mixtures were prepared, and those comprising the alcohol/water mixture showed a higher performance than the ones prepared using higher boiling solvents, such as dimethylacetamide; this is owing to the formation of the uniformly dispersed ionomer catalyst layer. The relation between ionomer molecular weight for the same polymer structure and the sulfonation degree was investigated. Because the chain length of polymer varies with molecular weight and chain entanglement degree, its molecular weight affects the electrode morphology. As the ionomer covered the catalyst, the agglomerates formed were of different morphologies according to their molecular weight, which could be deduced indirectly through dynamic light scattering and scanning electron microscopy. Additionally, the fuel cell performance was confirmed in the current-voltage curve.     

Mechanical damage characterization of glass fiber-reinforced polymer laminates by ultrasonic maps

A method for simultaneous measurement of the thickness and density for Glass Fiber-Reinforced Polymer (GFRP) laminate plates with ultrasonic waves in C-Scan mode is presented in the form of maps. The method uses three different signals in immersion pulse-echo C-Scan mode. The maps obtained based on the density show the heterogeneity of the material at high resolution at the pixel level (1 × 1 mm²) and therefore they represent an efficient tool to assess and evaluate the damage of the composite structures after manufacturing and after an applied mechanical loading.     

Behavior of 316L stainless steel containing corrosion pits under cyclic loading

The environmental performance of 316L grade stainless steel, in the form of tensile specimens containing a single corrosion pit with various aspect ratios, under cyclic loading in aerated chloride solutions is investigated in this study. Results from environmental tests were compared and contrasted with those obtained using finite element analysis (FEA). Fractography of the failed specimens obtained from experiments revealed that fatigue crack initiation took place at the base of the shallow pit. The crack initiation shifted towards the shoulder and the mouth of the pit for pits of increasing depth. This process is well predicted by FEA, as the strain contour maps show that strain is the highest around the centric strip of the pit. However, for shallow pits, local strain is uniformly distributed around that strip but begins to concentrate more towards the shoulder and the mouth region for increasingly deep pits.