Microstructure,tribological behavior and magnetic properties of Fe−Ni−TiO2 composite coatings synthesized via pulse frequency variation

The Fe−Ni−TiO₂ nanocomposite coatings were electrodeposited by pulse frequency variation. The results showed that the nanocomposite with a very dense coating surface and a nanocrystalline structure was produced at higher frequencies. By increasing the pulse frequency from 10 to 500 Hz, the iron and TiO₂ nanoparticles contentswere increased in expense of nickel content. XRD patterns showed that by increasing the frequency to 500 Hz, an enhancement ofBCC phase was observed and the grain size of deposits was reduced to 35 nm. The microhardness and the surface roughness were increased to 647 HV and 125 nm at 500 Hz due to the grain size reduction and higher incorporation of TiO₂ nanoparticles into the Fe−Ni matrix (5.13 wt.%). Moreover, the friction coefficient and wear rate values were decreased by increasing the pulse frequency;while the saturation magnetization and coercivity values of the composite deposits were increased.     

Wetting,infiltration and interaction behavior of CMAS towards columnar YSZ coatings deposited by plasma spray physical vapor

Thermal barrier coatings (TBCs) produced by electron beam physical vapor deposition (EB-PVD) or plasma spray (PS) usually suffer from molten calcium-magnesium-alumino-silicate (CMAS) attack. In this study, columnar structured YSZ coatings were fabricated by plasma spray physical vapor deposition (PS-PVD). The coatings were CMAS-infiltrated at 1250?°C for short terms (1, 5, 30?min). The wetting and spreading dynamics of CMAS melt on the coating surface was in-situ investigated using a heating microscope. The results indicate that the spreading evolution of CMAS melt can be described in terms of two stages with varied time intervals and spreading velocities. Besides, the PS-PVD columnar coating (～100?μm thick) was fully penetrated by CMAS melt within 1?min. After the CMAS attack for 30?min, the original feathered-YSZ grains (tetragonal phase) in both PS-PVD and EB-PVD coatings were replaced by globular shaped monoclinic ZrO₂ grains in the interaction regions.     

Polymer derived ceramic materials from Si,B and MoSiB filler-loaded perhydropolysilazane precursor for oxidation protection

Silica-based coating systems were developed using polymer derived ceramics (PDCs) technology. Ceramic composites on the base of a SiO₂ and SiNO matrix and homogeneously distributed Mo₅SiB₂, SiB₆, Si and B fillers were manufactured. The coating systems have low porosity and provide a high oxidation resistance up to 100 h at 800 °C and 1100 °C in air. The influence of temperature and atmosphere of pyrolysis on the polymer precursor, the volume fraction of filler materials on the chemical composition of compacts as well as their high-temperature oxidation protection was investigated.     

环保法规对船舶涂料企业的冲击及应对措施的探讨

随着我国环境保护法规《大气污染防治法》的修订和《涂料征收消费税通知》的公布,探讨了其对船舶涂料企业的冲击及其应对措施。     

High areal capacitance of FeOOH-carbon nanotube negative electrodes for asymmetric supercapacitors

The relatively low capacitance of negative electrodes, as compared to the capacitance of advanced positive electrodes, poses a serious problem, since this limits the development of asymmetric supercapacitor (SC) devices with a large voltage window and enhanced power-energy characteristics. We fabricate negative SC electrodes with a high capacitance that match the capacitance of advanced positive electrodes at similar active mass loadings, as high as 37?mg?cm^?2. Cyclic voltammetry, impedance spectroscopy, galvanostatic charge-discharge data and the power-energy characteristics of the asymmetric SC device exhibit good electrochemical performance for a voltage window of 1.6?V. Our approach involves the development and application of particle extraction through liquid-liquid interface (PELLI) methods, new extraction mechanisms and efficient extractors to synthesize α-FeOOH and β-FeOOH electrode materials. The use of PELLI allows agglomerate-free processing of powders, which facilitates their efficient mixing with multiwalled carbon nanotubes (MWCNT) and allows improved electrolyte access to the particle surface. Experiments to determine the properties of FeOOH-MWCNT composites provided insight into the influence of the electrode material and the structure of extractor molecules on the composite properties. The highest capacitance of 5.86?F?cm^?2 for negative electrodes and low impedance were achieved using α-FeOOH-MWCNT composites and a 16-phosphonohexadecanoic acid (PHDA) extractor. This extractor allows adsorption on particles, not only at the liquid-liquid interface, but also in the bulk aqueous phase and can potentially be used as a capping agent for particle synthesis and as an extractor in the PELLI method.     

粉料纯度的影响因素及对策

粉料的纯度直接影响骨料配方和沥青用量，从而影响糊料混捏质量。文章就影响粉料纯度的因素进行探讨，并提出一些对策，以期对生产有所指导。     

防腐蚀涂料的性能与选择

介绍并比较几种常用的防腐蚀涂料的品种、组成和性能特点，提出防腐蚀涂料的选择原则。     

粉末涂料在汽车涂装中的应用

介绍了粉末涂料的组成、优越性以及各种性能，分析了粉末涂料在汽车涂装中的经济性，肯定了粉末涂料在汽车工业中的应用前景。