转向驱动轮轮胎测力仪研究

该测力仪在结构上采用双等速万向节装置，不仅能用于转向轮和非转向轮的测量，并且解决了转向驱动轮的动力测量问题，对于四轮驱动的军用轮式车辆实车测试有着十分重要的意义。测力仪将轮胎动载荷、扭矩、侧向力、回正力矩、驱动力和外倾力矩的测量转化为测力筋拉压力的测量，大大提高了测量精度和抗干扰能力。     

非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经预退火后的晶化动力学的DTA研究

研究了非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经400℃，保温10min预退火后的晶化动力学。结果表明；该合金的晶化相为α-Fe固溶体和Sm2Fe17Cx金属间化合物，两相的晶化表观激活能分别为557KJ/mol和514KJ/mol，当晶化体积分数为60%时，α-Fe相的晶化激活能达极大值；Sm2Fe17Cx相晶化激活能则随其晶化体积分数的增加而逐渐减小。     

A NEW APPROACH FOR THE CLASSIFICATION AND ENUMERATION OF UNIQUE REACTION ROUTES AND UNIQUE OVERALL REACTIONS IN MULTIPLE CHEMICAL REACTION SYSTEMS

The methodology of response reactions (RERs) introduced earlier from thermodynamic and kinetic considerations is used in this work to develop a new algorithm for the classification and enumeration of unique/direct reaction routes (RRs) and overall reactions (ORs). According to the RERs approach, a unique set of both RRs and ORs may be generated starting from any conceivable set of linearly independent RRs and ORs. In particular, the direct ORs may be most conveniently enumerated starting from the formula matrix of the terminal species (reactants and products), i.e., without any relation to the elementary reactions comprising the detailed mechanism. Depending on the type of ORs produced by the RRs one can distinguish between two distinct types of direct RRs. Namely, one option is to define a direct RR by specifying the intermediate species that need to be eliminated. This type of RR is referred to as Milner RRs. The other option is to require the direct RRs to produce RERs, thus resulting in RRs referred to as Happel-Sellers RRs.     

Development of an integrated model for airflow in building spaces

In building energy simulation, an integrated modelling of airflow in the building needed. Therefore, in this paper two approaches are used for building energy simulation: zonal network for modelling of the building segments and Computational Fluid Dynamics (CFD) for modelling of the airflow. It is noted that a synchronize solution process is needed for the building and the CFD equation-sets. For this purpose an iterative procedure is used to corresponding solution of these equations.     

Improvement of oxygen mass transfer estimation from oxygen concentration measurements in bubble column reactors

An original procedure has been established for estimating the overall volumetric mass transfer coefficient using the oxygen concentration curves resulting from the usual gassing-in and gassing-out method. This procedure was applied to experimental data obtained in a small scale bubble column using both tap water and a coalescence-inhibiting liquid mixture that represents the coalescence behavior of biological media. It is based on the analysis of the characteristics times of the system, including those of the hydrodynamics of the two phases, the sensor dynamics and the system inertia when the gas composition is modified. A numerical procedure was developed to estimate the characteristic time of the system inertia t_i, using the assumption that this inertia is nearly independent of superficial gas velocity U_G. The calculations confirmed that the optimized t_i value was nearly independent of U_G and of the coalescence behavior of the liquid phase. Additionally, the resulting K_La_L values for tap water were closer to the correlation of Shah et al. [1982. Design parameters estimations for bubble column reactors. A.I.Ch.E. Journal 28, 353-379] than those of other conventional models. Finally, the original procedure was also reported to reduce significantly the square sum deviation between the predicted and the measured oxygen response curves.     

Analytical solution for the axisymmetric plane strain electroelastic dynamics of a special non-homogeneous piezoelectric hollow cylinder

By virtue of the introduction of a dependent variable and the separation of variables technique, the axisymmetric plane strain electroelastic dynamic problem of a special non-homogeneous piezoelectric hollow cylinder is transformed to a Volterra integral equation of the second kind about a function with respect to time, which can be solved successfully by means of the interpolation method. Then the solutions of displacements, stresses, electric displacements and electric potential are obtained. The present method is suitable for a piezoelectric hollow cylinder with an arbitrary thickness subjected to arbitrary mechanical and electrical loads. Numerical results are finally presented.     

Molecular Dynamics Simulation of Gas Diffusion in B2O3 and SiC

Molecular dynamics simulation using a universal force field has been employed to determine the diffusion coefficients of O2 and Na2SO4 vapor into B2O3 and SiC from 700 K to 1273 K, respectively. Einstein diffusion was observed in a 250～300 ps simulation.     

油气成藏动力学模拟现状与展望

油气成藏是包括油气生成、运移、聚集以及保存和破坏各个环节在内的复杂过程,受多种地质因素控制,与生烃中心、古今构造、生储盖组合、沉积相带、储层岩性等要素的演化均有关系。成藏动力学系统是含油气系统理论的新发展,是一门刚刚起步的新学科。油气成藏动力学研究有强大的计算机工作平台支持,模型研究与模拟研究结果的迭代反馈降低了地质解释中的多解性,是新一代的石油地质勘探研究的重要技术支撑系统。该文介绍了油气成藏动力学的产生与技术背景、原理模拟系统。最后对成藏动力学的发展提出展望。      

Simulation of Economic Dynamics under Ecological Balance Conditions

A model of economic dynamics under stable ecological balance conditions is proposed. A methodology of construction of an optimal growth path is constructed for this model.