Polyaniline as corrosion inhibitor for iron in acid solutions

In recent years, polymer amines have been studied as an efficient corrosion inhibitor for iron in acid media. In this article, the performance of water soluble polyaniline as corrosion inhibitor for iron in 0.5M H₂SO₄ has been evaluated by potentiodynamic polarization, linear polarization, and electrochemical impedance spectroscopy and compared with the performance of the aniline monomer. It has been found that polyaniline is an efficient inhibitor, since the maximum efficiency of 84% has been observed at a concentration of 100 ppm, whereas the monomer has accelerated the corrosion. FTIR studies have shown that the polyaniline is strongly adsorbed on the iron surface and inhibits the corrosion effectively. However, aniline has been found to improve the passivation tendency of iron at higher concentrations. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2144–2153, 2006     

Phase separation in polymer blends comprising copolymers: 6. Effect of molecular architecture of block copolymers

To study the effect of the molecular architecture of a copolymer on its miscibility with corresponding homopolymers a series of block copolymers of styrene and isoprene with diblock, triblock and four-arm star architectures have been prepared and the morphologies of the blends of the copolymers and polyisoprene with different molecular weights have been examined by electron microscopy. The results show that miscibility varies in the sequence diblock>triblock>four-arm star copolymers. This sequence is in the opposite direction to the variation of the architectural complexity of the block copolymers, i.e. the more complex is molecular architecture, the greater is conformation restriction in microdomain formation and the less is solubility of homopolymer in corresponding domains.     

CFRP加固钢筋混凝土梁滞后应变计算方法

为了系统研究从零负载状态到满负载状态各个阶段CFRP片材加固梁滞后应变的计算方法,在充分考虑加固梁不同负载状态及受压区混凝土非线性本构关系的基础上,分别建立了不同负载贴片加固梁考虑混凝土抗拉作用时的滞后应变计算公式及不考虑混凝土抗拉作用时的简化计算公式.试验数据和对比分析结果表明:"考虑混凝土抗拉作用"公式的计算结果与试验数据吻合良好,计算误差<8%,明显优于现有文献的计算方法;"不考虑受拉区混凝土抗拉作用"公式的计算结果在混凝土开裂前和试验值相差较大,但对已裂加固梁的计算误差与"考虑混凝土抗拉作用"公式的计算误差接近.为简化计算,对未裂和已裂混凝土梁贴片加固时的滞后应变可分别采用"换算截面"公式和"不考虑混凝土抗拉作用"公式进行计算,两种简化方法的误差均不会超过10%.     

Electrocatalytic activity of oxidation products of guanine and 5′-GMP towards the oxidation of NADH

We have studied the potential electrocatalytic activity towards the oxidation of NADH of several oxidation products of guanine and its derivative guanosine-5′-monophosphate (5′-GMP) on pyrolytic graphite electrodes (PGE). The distribution of products generated strongly depends on the experimental conditions. Our investigations focused on the oxidation products that are adsorbed on the electrode surface, are redox active and, exhibited electrocatalytic activity toward the oxidation of NADH. These compounds were electrochemically and kinetically characterized in terms of dependence of the formal potential on pH and electron transfer rate constant (k_s). The voltammetric and catalytic behavior of both guanine and 5′-GMP oxidation products was compared with that of other guanine derivatives we have previously studied. Some mechanistic aspects concerning the generation of the catalysts are also discussed.     

Milled fibre reinforced epoxy resin — an engineering polymer composite

A milled fibre reinforced epoxy resin composite (MFRE) has been developed for low temperature use. It is resistant to fracture at temperatures down to at least 77 K in direct contact with liquefied gases. It can be used as an adhesive, a gap-filling mastic or a moulding compound for difficult cryogenic applications. The characteristics of the material and some applications are described.     

Highly ion-conductive solid polymer electrolytes based on polyethylene non-woven matrix

Highly ion-conductive solid polymer electrolyte (SPE) based on polyethylene (PE) non-woven matrix is prepared by filling poly(ethylene glycol) (PEG)-based crosslinked electrolyte inside the pores of the non-woven matrix. The PE non-woven matrix not only shows good mechanical strength for SPE to be a free-standing film, but also has very porous structure for high ion conductivity. The ion conductivity of SPE based on PE non-woven matrix can be enhanced by adding sufficient non-volatile plasticizer such as poly(ethylene glycol) dimethyl ether (PEGDME) into ion conduction phase without sacrificing mechanical strength. SPE with 20 wt.% crosslinking agent and 80 wt.% non-volatile plasticizer shows 3.1 × 10⁻⁴ S cm⁻¹ at room temperature (20 °C), to our knowledge, which is the highest level for SPEs. It is also electrochemically stable up to 5.2 V and has high transference number about 0.52 due to the introduction of anion receptor as an additive. The interfacial resistance between Li electrode and SPE is low enough to perform charge/discharge test of unit cell consisting of LiCoO₂/SPE/Li at room temperature. The discharge capacity of the unit cell shows 87% of theoretical value with 86% Coulombic efficiency.     

Dispirations,disclinations, dislocations,and chain twist in polyethylene crystals

It is proposed that the twist in polyethylene chains that can result from crystallization and subsequent deformation aggregates at boundaries and becomes a template for further reorganization that results in the long period observed in polyethylene fibres. The observed lower density at the boundaries requires the transport of free volume to the twist boundaries. Dispirations, disclinations and dislocations are crystallographic defects that are involved in the necessary transport mechanism. Twist and bend, derived from the Eulerian angles which are computed from the sets of chain internal coordinates, relate the orientation of different segments of a chain. Twist and bend are useful for the characterization of both crystallographic defects and arbitrary conformations of polymer chains. Defects, along with folds, chain ends, and ordinary edge and screw dislocations provide a basis for interpretation of structure-property relationships in solid polyethylene.     

多羟甲基酚多丙烯酸酯的合成及其耐温性能研究

本文合成了新型耐温活性预聚体多羟甲基酚多丙烯酸酯,并考察了pH值,丙烯酸量,反应时间、反应温度、催化剂用量等因素对反应产率的影响。测试了固化物的TCA和DTA及力学性能,并用红外光谱确认主产物。