Geopolymer concrete-filled pultruded composite beams – Concrete mix design and application

The limited research on the geopolymer concrete mix design for targeting a specific strength is identified an obstacle for their effective design and wide use. In this paper, a mix design procedure has been proposed for fly-ash based geopolymer concrete and its use as infill hybrid composite beam is investigated. Then, the structural performance of geopolymer concrete filled hybrid composite beam is investigated to determine their possible application in civil infrastructure. Firstly, a detailed procedure of mix design for fly-ash based geopolymer concrete is presented. Secondly, three hybrid beams filled with geopolymer concrete were prepared and tested in a four-point bending setup to evaluate their flexural modulus and modulus of rupture. Numerical and analytical evaluation of the behaviour of hybrid beam were performed and results showed a good agreement with the experimental investigation. Thirdly, the suitability of the beam for a composite railway sleeper is evaluated and compared with existing timber and composite sleepers. Finally, the beams’ performance in a ballast railway track is analysed using Strand7 finite element simulation software and the results showed that the new concept of using geopolymer concrete as infill to pultruded composite section satisfied the stiffness and strength requirements for a railway sleeper.     

Chloride migration in concrete with superabsorbent polymers

Superabsorbent polymers (SAP) can be used as a means for internal curing of concrete. In the present study, the development of transport properties of concrete with SAP is investigated. The chloride migration coefficient according to NT BUILD 492 is used as a measure of this. Twenty concrete mixtures are tested 7, 14, and 28 days after casting. The development of degree of hydration is followed for 20 corresponding paste mixtures.Both when SAP is added with extra water to compensate the SAP water absorption in fresh concrete and without extra water, the internal curing water held by SAP may contribute to increase the degree of hydration. No matter if SAP is added with or without extra water, it appears that the so-called gel space ratio can be used as a key parameter to link age and mixture proportions (water-to-cement ratio and SAP dosage) to the resulting chloride migration coefficient; the higher the volume of gel solid relative to the space available for it, the lower the chloride migration coefficient, because the pore system becomes more tortuous and the porosity becomes less.     

埋地管道泄漏内封堵装置设计与研究

针对流体输送埋地管道泄漏问题,设计了一种利用管道机器人携带封堵气囊进行快速应急封堵修复的埋地管道泄漏内封堵装置。采用矩阵变换方法建立了牵引系统驱动轮过弯方程,利用MATLAB软件对过弯方程进行了验证,同时利用ADAMS软件仿真分析过弯路径与驱动轮转角对牵引系统行走速度的影响。研究结果表明:由两个串联封堵器组成的应急封堵系统可满足复杂工况下的管道泄漏封堵要求;牵引系统驱动轮在弯管内部行走时,单轮速度呈周期性变化,但三个驱动轮整体周期运动特性一致;驱动轮转角在25°~40°时,牵引系统行走速度与驱动轮转角成正比,且转角为30°时驱动效果最好。该内封堵装置的结构设计可为管道泄漏应急封堵领域装备的研发提供重要参考。     

Ballistic behavior of plain and reinforced concrete slabs under high velocity impact

This work presents a numerical simulation of ballistic penetration and high velocity impact behavior of plain and reinforced concrete slabs. In this paper, we focus on the comparison of the performance of the plain and reinforced concrete slabs of unconfined compressive strength 41 MPa under ballistic impact. The concrete slab has dimensions of 675 mm × 675 mm × 200 mm, and is meshed with 8-node hexahedron solid elements in the impact and outer zones. The ogive-nosed projectile is considered as rigid element that has a mass of 0.386 kg and a length of 152 mm. The applied velocities vary between 540 and 731 m/s. 6 mm of steel reinforcement bars were used in the reinforced concrete slabs. The constitutive material modeling of the concrete and steel reinforcement bars was performed using the Johnson-Holmquist-2 damage and the Johnson-Cook plasticity material models, respectively. The analysis was conducted using the commercial finite element package Abaqus/Explicit. Damage diameters and residual velocities obtained by the numerical model were compared with the experimental results and effect of steel reinforcement and projectile diameter were studies. The validation showed good agreement between the numerical and experimental results. The added steel reinforcements to the concrete samples were found efficient in terms of ballistic resistance comparing to the plain concrete sample.     

浅议我国上市公司内部控制环境优化

控制环境是内部控制框架的基础,由于我国目前上市公司内部控制体系建设尚处于初级阶段,决定了其内部控制环境呈现出固有弊端.分析了我国上市公司在控制环境方面存在的缺陷,并提出了相应的优化措施,以期能对内部控制环境的完善起到一定的作用.     

寒冷地区高温干燥条件下混凝土面板裂缝控制

希尼尔水库位于新疆巴音郭楞蒙古族自治州境内，气候特点为高温、干燥、冬季寒冷。根据混凝土面板产生裂缝的原因，并结合工程区的气候特点，认为控制面板的塑性收缩、干缩与冷缩裂缝是防止裂缝产生的重点。通过采用高性能混凝土，合理的养护措施(微喷灌洒水技术)，有效地防止了裂缝的产生，保证了工程质量。     

大体积抗渗混凝土工程施工技术

简述了浇筑混凝土的施工准备工作，从滑动层的增设、配合比的配制、混凝土的浇筑及养护、后浇带的处理等方面介绍了大体积抗渗混凝土工程的施工质量控制措施，以保证混凝土的各项指标达到规范及设计要求。     

Rheological cure characterization of phosphazene–triazine polymers

Cyclomatrix phosphazene–triazine network polymers were synthesized by co‐curing a blend of tris(2‐allylphenoxy), triphenoxy cyclotriphosphazene (TAP), and tris(2‐allylphenoxy) s‐triazine (TAT) with bis(4‐maleimido phenyl) methane (BMM). The co‐curing of the three‐component resin was investigated by dynamic mechanical analysis using rheometry. The cure kinetics of the Diels–Alder step was studied by examining the evolution of the rheological parameters, such as storage modulus (G′), loss modulus (G″), and complex viscosity (η*), for resins of varying compositions at different temperatures. The curing conformed to an overall second‐order phenomenological equation, taking into account a self‐acceleration effect. The kinetic parameters were evaluated by multiple‐regression analysis. The absence of a definite trend in the cure process with blend composition ratio was attributed to the occurrence of a multitude of competitive reactions whose relative rates depend on the reactant ratio and the concentration of the products formed from the initial phase of reaction. The cure was accelerated by temperature for a given composition, whereas the self‐acceleration became less prominent at higher temperature. Gelation was accelerated by temperature. The gel conversion decreased with increase in maleimide concentration and, for a given composition, it was independent of the cure temperature. The activation energy for the initial reaction and the crosslinking process were estimated for a composition with a maleimide‐to‐allyl ratio of 2 : 1. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 908–914, 2003     

浇筑式沥青混凝土心墙型式改进的建议

本文根据浇筑式沥青混凝土主、副心墙材料的性能，分折了沥青混凝土心墙施工或运行中破坏的原因，建议用编织一无纺复合布取代预制块，以避免主、副心墙材料变形性能相差悬残对心墙运行的不利影响，从而发挥浇筑式沥青混凝土心墙的优越性。