Macrosegregation in Cu–30Ni welds made with dissimilar filler metals

Abstract

To study macrosegregation in arc welds made with filler metals different (dissimilar) from the workpiece in composition, gas metal arc welding of alloy Cu–30Ni was conducted. With a pure Cu filler metal, a large filler rich zone was observed near the weld bottom with islands of partially mixed base metal scattered in the zone well within the fusion boundary. With a pure Ni filler metal, on the other hand, a large filler rich zone was again observed near the weld bottom but with filler rich intrusions penetrating into a thick continuous filler deficient beach along the fusion boundary. These results were explained based on two mechanisms proposed recently by the authors for macrosegregation near the bottoms of dissimilar filler welds, i.e. mechanism 3 for T_LW<T_LB and mechanism 4 for T_LW>T_LB, where T_LW is the liquidus temperature of the weld metal and T_LB that of the base metal.     

Mechanism of pinhole generation during welding of flake graphite cast iron and effects of composition of base metal

Abstract

The mechanism of pinhole generation during welding flake graphite cast iron is examined. As a result, the oxidisation progresses inwardly along the interface between matrix and flake graphite, and then oxides such as SiO₂ and MnO are generated. The oxidisation progresses through the graphite in the surface of the nearby eutectic cell. When oxidised cast iron is welded, oxides are deoxidised by the graphite and carbon monoxide gas is generated. The carbon monoxide gas comes up to the surface of the welding bead, but sometimes does not reach the surface and it becomes solidified from the top because the cooling rate at welding is very fast. This is how pinholes are generated.

Also the effect of components of flake graphite cast irons on the pinhole generation is investigated. The number of pinholes increases with the increase in C, Si, Mn, Ni or Cu. Conversely, when the elements of P, S, Cr, Mo and Mg increase, it becomes difficult to generate pinholes.     

Papers to be presented at Eurocor '77

Abstract

Despite numerous studies on atmospheric corrosion of copper and copper based alloys, the corrosion induced release processes of individual alloy constituents suffer from significant knowledge gaps. This investigation comprises metal release rate measurements of copper, zinc and tin from some copper based alloys including brass (20 wt-%Zn) and bronze (6 wt-%Sn), and their pure alloying metals, copper, zinc and tin. Data have been generated during a 2·5 year urban field exposure in Stockholm, Sweden and parallel laboratory investigations in a specially designed rain chamber using artificial rain. Brass shows significantly lower annual release rates of both copper and zinc compared to pure metal sheets of its alloy constituents. Zinc is preferentially released compared to copper. Dezincification of brass occurs both at field and laboratory conditions, a process influenced by rain characteristics. Alloying with tin does not largely reduce the release rate of copper from bronze compared to pure copper. No measurable amount of tin is released from the bronze surface.     

Kinetics and dilatometric behaviour of non-isothermal ferrite–austenite transformation

Abstract

A model that describes the ferrite–austenite transformation during continuous heating in Armco iron and three very low carbon, low manganese steels with a fully ferritic initial microstructure is presented. This model allows calculation of the volume fractions of austenite and ferrite during transformation as a function of temperature, and hence knowledge of the austenite formation kinetics under non-isothermal conditions in fully ferritic steels. Moreover, since dilatometric analysis is a technique very often used to study phase transformations in steels, a second model, which describes the dilatometric behaviour of the material and calculates the relative change in length that occurs during the ferrite–austenite transformation, has also been developed. Both kinetics and dilatometric models have been validated by comparison of theoretical and experimental dilatometric heating curves. Predicted and experimental results are in satisfactory agreement.     

Overview Inclusion assisted microstructure control in C–Mn and low alloy steel welds

Abstract

Inclusion assisted microstructure control has been a key technology to improve the toughness of C–Mn and low alloy steel welds over the last two to three decades. The microstructure of weld metals and heat affected zones (HAZs) is known to be refined by different inclusions, which may act as nucleation sites for intragranular acicular ferrite and/or to pin austenite grains thereby preventing grain growth. In the present paper, the nature of acicular ferrite and the kinetics of intragranular ferrite transformations in both weld metals and the HAZ of steels are rationalised along with nucleation mechanisms. Acicular ferrite development is considered in terms of competitive nucleation and growth reactions at austenite grain boundary and intragranular inclusion nucleation sites. It is shown that compared to weld metals, it is difficult to shift the balance of ferrite nucleation from the austenite grain boundaries to the intragranular regions in the HAZ of particle dispersed steels because inclusion densities are lower and the surface area available for ferrite nucleation at the austenite grain boundaries tends to be greater than that of intragranular inclusions. The most consistent explanation of high nucleation potency in weld metals is provided by lattice matching between ferrite and the inclusion surface to reduce the interfacial energy opposing nucleation. In contrast, an increase in the thermodynamic driving force for nucleation through manganese depletion of the austenite matrix local to the inclusion tends to be the dominant nucleation mechanism in HAZs. It is demonstrated that these means of nucleation are not mutually exclusive but depend on the nature of the nucleating phase and the prevailing transformation conditions. Issues for further improvement of weldment toughness are discussed. It is argued that greater numbers of fine particles of a type that preferentially nucleate acicular ferrite are required in particle dispersed steels to oppose the austenite grain boundary ferrite transformation and promote high volume fractions of acicular ferrite and thereby toughness.     

Investigation of microstructure and mechanical properties of steel fibre–cast iron composites

Abstract

The aim of the present experimental study was to investigate improvement of the toughness and strength of grey cast iron by reinforcing with steel fibres. The carbon content of the steel fibres was chosen to be sufficiently low that graphite flakes behaving as cracks were removed by carbon diffusion from the cast iron to the steel fibres during the solidification and cooling stages. To produce a graphite free matrix, steel fibres with optimum carbon content were used and the reinforced composite structure was cast under controlled casting conditions and fibre orientation. Three point bend test specimens were manufactured from steel fibre reinforced and unreinforced flake graphite cast iron and then normalising heat treatments were applied to the specimens at temperatures of 800 and 850°C. The fracture toughness and strength properties of the steel fibre reinforced material were found to be much better than those of unreinforced cast iron. The microstructures of the composite at the fibre–matrix transition zone were examined.     

Through thickness residual stresses in large rolls and sleeves for metal working industry

Abstract

There is little experimental knowledge about the initial state of through thickness residual stresses in rolls and sleeves for the steel rolling industry. This is surprising bearing in mind the impact that residual stress has on the performance of the roll and sleeve materials in the highly aggressive loading environments of the metal working industry. Previous work has been confined to measurement of very near surface residual stresses and numerical predictions of residual stress distributions. In the present paper through thickness residual stress measurements were carried out using a deep hole drilling technique on a series of rolls and sleeves representative of those used in the rolling industry. Different features of the manufacturing processes used in their production are shown to influence the magnitude and distribution of the residual stresses. It is also shown that the measurements can be used, together with a finite element analysis, to determine the volumetric distribution of the residual stresses.     

Calcium silicate based high efficiency thermal insulation

Abstract

The preparation by hydrothermal synthesis of a high efficiency, calcium silicate based thermal insulation is described using raw material mixes of silica, bentonite, and magnesium acetate or acetic acid. The materials were reacted in a high pressure autoclave at 200–250°C resulting in a product consisting of cenospheres of needle-like xonotlite crystals and some tobermorite. Properties including density, strength, microstructure, thermal stability, and water absorption and water repellence are presented.     

Numerical simulation of metal powder die compaction with special consideration of cracking

Abstract

Powder die compaction is modelled using the finite element method and a phenomenological material model. The Drucker–Prager cap model is modified with the goal to describe the formation of cracks during powder transfer, compaction, unloading, and ejection of the parts from the die. This is achieved by considering the cohesive strength and the cohesion slope, which characterise the current strength of the powder compact in the Drucker–Prager model, as state dependent variables. Evolution equations are formulated for these variables, so that the strength increases by densification and decreases by forced shear deformation. Some of the parameters appearing in the evolution equations are determined from measured green strength values. An iron based powder (Distaloy AE) is used for the experiments. Examples are shown to demonstrate that the density distribution can be calculated accurately as compared with an experiment, that cracking can be modelled at least qualitatively correctly, and that the compaction of complex 3D parts can be simulated.     

Behaviour of metal powders during cold and warm compaction

Abstract

An instrumented die was used to investigate the behaviour of metal powders during cold (ambienttemperature) and warm (up to 140^°C) compaction. This instrument enables simultaneousmeasurement of density, die wall friction coefficient, the triaxial stresses acting on the powderduring the course of compaction and ejection pressure. Commercial iron, titanium, aluminium,316L stainless steel (SS) and aluminium–silicon powders were employed for investigation. Theresults demonstrated the advantages of powder preheating on the compaction behaviour of metalpowders concerning green density, dimensional changes, frictional behaviour, ejectioncharacteristics and compactibility. However, the outlines also determined that the response ofthe non-ferrous powders to powder preheating is somehow different from those of the ferrouspowders. In this context, the behaviour of prealloy aluminium–silicon powders during compactionwas found of particular interest, as their compactibility is strongly affected by powder preheating,whereas the dimensional changes after ejection decrease considerably. This article presents theeffect of cold and warm compaction on the consolidation and ejection characteristics of ferrousand non-ferrous metal powders. The influence of compaction condition (pressure andtemperature) with considering of the powder characteristics and densification mechanisms areunderlined.