Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

MgO在含铅PTCR陶瓷中的作用

研究了ＭｇＯ加入到含铅ＰＴＣＲ陶瓷中的作用。用碱土金属Ｍｇ２＋对（Ｂａ，Ｐｂ）ＴｉＯ３掺杂，在１２４０～１３００℃空气中烧结，获得工艺性能良好，烧结温度较低，电性能优良的ＰＴＣＲ陶瓷材料。试验结果表明：ＭｇＯ的加入降低了含铅ＰＴＣＲ陶瓷的烧结温度，抑制了ＰｂＯ的挥发。     

Processing and microstructure of non-oxide ceramic fibres

Research and development efforts on high-temperature, oxidation-resistant fibres have increased over the past decade due to the demand for light-weight, stiff and strong composite materials in aerospace applications. Varieties of ‘high-performance’, continuous, non-oxide fibres with low-density, high tensile strength and tensile modulus have been developed either from organic precursors or via chemical vapour deposition for fabrication of ceramic matrix composites. Fibres derived from polymer precursors (e.g. Nicalon, Tyranno, HPZ) are small in diameter (compared to CVD monofilaments) and are ideally suited for ceramic composites. Processing, microstructural stability and mechanical properties of these newly developed SiC and Si₃N₄ base fibres are briefly reviewed in this paper.     

SiC／Al合金层状复合材料的机械性能及损伤行为

在室温条件下测定了Ａｌ合金以连续层状形式存在于ＳｉＣ陶瓷层间并渗透入ＳｉＣ陶瓷层内、Ａｌ合金浓度呈层状变化高低相间，以及Ａｌ合金和ＳｉＣ陶瓷均匀分布相互渗透三种ＳｉＣ含量相同而结构形式不同的ＳｉＣ／Ａｌ合金复合材料的机械性能；用ＳＥＭ和光学显微镜观察分析了复合材料的断口形貌及裂纹扩展过程。结果表明，在ＳｉＣ陶瓷层间以连续层状形式存在的Ａｌ合金在应力作用下发生较大程度的塑性变形，在裂纹尾部被拉伸和形成桥接，引起能量耗散，减缓裂纹扩展速度，防止裂纹张开，使复合材料的韧性得到明显改善；ＳｉＣ／Ａｌ合金陶瓷─金属层状复合材料的损伤形式主要是ＳｉＣ陶瓷层开裂、金属层桥接和裂纹偏转。     

三维连通网络陶瓷的电磁特性Ⅱ电磁参数的影响因素

通过对具有不同骨架L径、陶瓷浆料组分在不同温度下烧结的三维连通网络陶瓷的电导率和电磁参数的测量,研究了对这种网络结构材料电磁参量的影响因素.结果表明,当三维连通网络陶瓷的电导率为10-4＜σ＜101S/cm时,其电损耗及感应磁损耗较大.三维连通网络陶瓷在高温下有较大的介电损耗特性,使其成为耐高温电吸波材料的理想选择.     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

提高自蔓延高温合成陶瓷内衬钢管性能的研究

在概括了自蔓延高温合成陶瓷内衬钢管的制备原理基础上，从降低陶瓷层孔隙率，减少陶瓷层裂纹和提高陶瓷层结合强度等方面，论述了提高自蔓延高温合成陶瓷内衬钢管性能的措施，对自蔓延高温合成陶瓷内衬钢管的应用现状及展望进行了评述。     

Thermal-lens and photo-acoustic methods for the determination of SiC thermal properties

In this paper we report the use of photothermal techniques such as Thermal lens (TL) spectrometry, Photoacoustic and heat capacity, ρc_p, to determine the thermo-optical parameters, such as thermal conductivity (K), thermal diffusivity (D), specific heat (c_p) and the optical path dependence with temperature (ds/dT), of an undoped polycrystalline 3C-SiC. To our knowledge, this is the first time that Thermal lens technique is used for wide band-gap systems. Results obtained for the polycrystalline sample with TL technique indicates that ds/dT is negative at room temperature. Moreover, the obtained values of thermal diffusivity and thermal conductivity are in good agreement with that found in the literature, indicating that the phototermal techniques can be used to obtain the referred parameters in circumstances where other techniques cannot be used, for example, in harsh environments.     

多孔材料透过性能的表征

透过性能对用于过滤分离、流体混合、布气分流等方面的多孔材料是一项十分关键的质量指标。主要介绍了多孔材料透过性能的表征方式，包括流体流动的基本概念、层流条件下流体的透过性能表征、多孔材料透过性能的综合表征、气体透过多孔材料时渗透系数的具体表征等方面。     

Spin Dependent Hopping in Ti Doped La0.67 Ca0.33 MnO3

A systematic investigation of the magnetic and transport properties of Ti doped La0.67Ca0.33MnO3 was reported. The Ti substitution for Mn ions results in a reduction in ferromagnetism and conductivity. The metal-insulator transition temperature is close to Curie temperature which decreases from 274 to 82 K as x increases from 0 to 0.17. The most important effect of Ti doping is to introduce spin clusters in the samples due to the distortion of local lattice and the inhomogeneous magnetic structure induced primarily by the random distribution of Mn ions. A maximum magnetoresistance ratio as large as 90% in 1 T at 122 K was obtained for the sample with x =0. 055, which is four times larger than that obtained for LCMO sample at 272 K. There is a remarkable field-history dependent MR in the cooling process for the doped samples while such phenomenon disappears in the warming run. The resistivity follows well the variable range hopping behavior in paramagnetic state. Both the size effect and spin dependent hopping of carriers between the spin clusters should be considered in this system.