尼龙-11粉末涂料

本文简要地介绍了我国粉末涂料的发展概况，并概述了热固性和热塑性粉末涂料的应用领域．文章重点介绍了尼龙－１１粉末涂料的优点及其制造法，阐述了其在管道防腐、船体防护和建筑行业等领域的应用     

PZT polarization voltage effects on off-centered PZT patch actuating silicon membrane

We have investigated the static and dynamic behavior of piezoelectric (PZT) actuated SiO₂/Si membranes with an off-centered PZT patch. Three-dimensional wide-field interferometer has been used to achieve measurement of membrane topography and bending. It is demonstrated that the piezoelectric coefficient d₃₁ can be extracted directly from these three-dimensional static deformation measurements. We have also shown that polarization voltage of an off-centered PZT patch influences in a different manner the resonant frequency shift of the first and the second vibration modes. Degenerated modes can be also discriminated thanks to the positioning of the PZT patch.     

High-Temperature Strength of Niobium Alloy 5VMTs with a Silicide-Ceramic Coating. Part 1. Short-Term Strength Characteristics

Experimental data on the short-term strength and plasticity of niobium alloy 5VMTs of the system Nb–W–Mo–Zr in its initial state, after annealing, and with a silicide-ceramic protective coating obtained by testing in vacuum, an inert atmosphere, and in air in the temperature range from 290 to 2270 K are analyzed. The process of microcrack initiation and propagation in the protective coating and matrix is investigated in high-temperature static tension. The limiting plastic strain values have been established at which the composite retains its load-carrying capacity in high- temperature aggressive and oxidizing gas atmospheres.     

Effects of lubrication and humidity on the abrasiveness of a thin boron carbide coating

Studies using thin boron carbide (B₄C) coatings have previously been performed in order to investigate their potential use as finite-life run-in coatings. Such coatings have been shown to polish the mating surface in a relatively short time. The inherent ability of these coatings to polish can potentially allow them to function as finite-life run-in coatings. Employing such coatings requires a thorough understanding of the parameters which directly influence the changes that occur in the coating abrasiveness throughout the duration of the polishing process. In past studies, changes in the coating abrasiveness during dry sliding wear under ambient conditions have been investigated. However, both lubrication and humidity can strongly influence the abrasive wear process. In this study, the influences of the operating environment, namely humidity and lubrication, on the coating abrasiveness are directly investigated. The coating abrasiveness decreases at a slower rate when a lubricant is added and when the humidity decreases.     

The Effect of Coolant Concentration on the Machinability of Nickel-Base, Nimonic C-263, Alloy

This paper investigates the effect of coolant concentration on tool performance when machining nickel-base, C-263, alloy with triple coated (TiN/TiCN/TiN) carbide insert at various (3–9%) coolant concentrations and under different cutting speed conditions. Tool life, tool-failure modes, wear rates, component forces and surface finish generated during machining were recorded, analyzed and used to formulate mechanisms responsible for tool wear at the cutting conditions investigated. Analysis of the recorded data shows that tool performance during machining is dependent on coolant concentration. 6% coolant concentration gave the best overall performance as effective combination of cooling and lubrication functions were achieved during machining. Increasing coolant concentration to 9% reduced tool performance due to a reduction of the tool-chip contact length area and the consequent increase in compressive stresses at the tool-chip and tool-workpiece interfaces. This action often leads to pronounced chipping of the tool cutting edge during machining. Friction coefficient between the workpiece material and substrate increases once the coating layer(s) is broken as a result of the direct contact between the tool substrate and the work material. This action increases mechanical wear of the tool, which in turn leads to a significant increase in the cutting force with negligible effect on the feed forces during machining.     

消失模铸造铸铁件水基涂料的研制

选用石英粉为耐火骨料，酸式磷酸盐为粘结剂，通过正交试验确定了铸铁件消失模水基涂料的最佳配比。经测试和生产验证，其性能良好，能很好地适应生产要求。     

正极材料LiNi1/3CO1/3Mn1/3O2包覆LiNi0.8Co0.15Al0.05O2的性能

以NiSO4·6H2O、CoSO4·7H2O、MnSO4·H2O、NH3·H2O及NaOH为原料,采用共沉淀方法在LiNi0.8 C00.15 Al0.05 (OH)2球形粒子表面包覆一层Ni1/3 Co1/3Mn1/3(OH)2三元材料前驱体,配锂后在750℃下、氧气气氛中焙烧12 h,合成复合层状材料Li[(Ni0.8 Co0.15Al0.05)0.97(Ni1/3Co1/3Mn1/3)0.03]O2.复合层状材料具有核壳结构,包覆壳层的厚度约为1μm.复合层状材料在2.8～4.3 V充放电,0.1C首次放电比容量为188.2 mAh/g;0.2 C循环100次的容量保持率为96.2％;在55℃下以0.2C循环100次,放电比容量保持在163.2 mAh/g.     

TiB_2/ZrB_2/SiC复合功能材料的微观结构与力学性能

采用放电等离子烧结工艺,制备TiB2/ZrB2/SiC复合功能材料。用X射线衍射仪和场发射扫描电镜分析观察复合材料的物相组成及微观形貌。并测试复合材料的抗弯强度、断裂韧性及硬度。结果表明:两次球磨后的TiB2/ZrB2/SiC粉体粒度较小(2~4μm),且分布较均匀,几乎没有团聚现象。烧结后的复合功能材料中有(TixZry)B2固溶体相生成。当加入ZrB2的体积分数为30%时,生成的(TixZry)B2固溶体在复合材料中起到了很好的晶粒细化与界面融合作用,所以TZS30复合陶瓷材料比TZS0复合陶瓷材料的抗弯强度和断裂韧性分别提高了119.8%和98.9%。利用TiB2/ZrB2/SiC复合陶瓷材料在高温摩擦作用下与氧的化学反应,可以实现自润滑。     

Effects of a base coating used for electropolymerization of poly(3,4-ethylenedioxythiophene) on indium tin oxide electrode

Electropolymerization of poly(3,4-ethylenedioxythiophene) (PEDOT) films on indium tin oxide (ITO), using a very thin PEDOT:poly(styrene sulfonate) (PEDOT:PSS) film as a base coating, was carried out in a non-aqueous solution containing the monomer, an electrolyte and propylene carbonate by a two-electrode system. For comparison, PEDOT film electrodeposited on bare ITO substrate under the same condition was also presented. The PEDOT films deposited on these two substrates were characterized by scanning electron microscopy, energy disperse X-ray spectroscopy and Raman spectroscopy. The results indicate that the PEDOT film electrodeposited on bare ITO was not uniform, while the PEDOT film electrodeposited on PEDOT:PSS/ITO has better uniformity. The compositions of the different regions of PEDOT film electrodeposited on bare ITO and PEDOT:PSS/ITO were studied and discussed. Electrochromic devices (ECDs) based on PEDOT films electrodeposited on bare ITO and PEDOT:PSS/ITO were fabricated and characterized by UV-Vis-NIR spectrophotometric study. The results show that the display contrast of the ECD based on PEDOT film electrodeposited on PEDOT:PSS/ITO was improved over that on a bare ITO substrate.     

Microstructure and properties of nc-TiC/a-C∶H films deposited by radio frequency reactive sputtering

Abstract

Amorphous carbon films containing titanium carbide (nc-TiC/a-C∶H) were deposited onto n-type silicon (100) by radio frequency reactive sputtering titanium target in an Ar–CH₄ mixed atmosphere. The composition and microstructure of the films were characterised by means of X-ray photoelectron spectroscopy, field emitted SEM, XRD and Raman spectra. The mechanical and tribological properties of the films were measured by a nanoindentation tester and a ball-on-disc UMT–2MT tribometer. By adjusting the CH₄ flowrate, Ti content in the films could be controlled, and a transition in structures of the films from loose polymer-like to glassy and dense nanostructure was observed. The density of coatings was improved by the introduction of TiC nanocrystalline particles. The mechanical and lubricious properties were different accordingly.