Growth of Au nanocrystals on CdS nanorods

Nanorods of S²⁻ rich CdS were synthesized by a reaction of excess S versus Cd precursors in the presence of ethylene diamine. The photoluminescence (PL) emission from the S²⁻ rich CdS nanorods was broad with a peak at ∼710 nm, which was 40 nm longer in wavelength than the PL peak from Cd²⁺ rich CdS (∼670 nm) nanorods. The influence of surface electron or hole trap states on the luminescent pathway of CdS nanorods will be discussed to explain these shifts in wavelength. Nanocrystals of Au ∼2 nm in size were grown on S²⁻ rich surfaces of CdS nanorods. Significant luminescence quenching was observed from the Au nanocrystals on the CdS nanorods due to interfacial charge separation. Change separation by the Au nanocrystals on the CdS resulted in enhanced photocatalytic degradation of Procion red mix-5B (PRB) dye in an aqueous solution under UV light irradiation.     

中频用极薄热轧硅钢片的研制

选用合适成分，采用两次折叠、16层叠轧的方法开发出性能优异的0．25mm厚的中频（400、1000Hz）用权薄热轧硅钢片，已用于生产，并取得良好成绩。     

A closed form solution for laser drilling of silicon nitride and alumina ceramics

A closed form solution has been obtained for laser drilling of silicon nitride (Si₃N₄) and alumina ceramics (Al₂O₃). The drilling of workpiece is performed by using a TEM₀₀ 10 ns pulse Nd:YAG laser. It is assumed that the phase transition from solid to vapor occurs without melting. Considering the absorption of plasma plume formed on the surface of the ceramics, the one-dimensional thermal model is developed in order to describe the drilling process. The governing equation of heat-diffusion is solved analytically using a Laplace transformation method. Erosion depth per laser pulse obtained from the closed form solution agrees with the available experimental data.     

Nitridation Kinetics of Silicon Monocrystal and Morphology of Nitride Film

Basing on TGA (thermal gravimetric analysis) of thermal nitridation at l200, l250, l300℃, respectively,analysis of high temperature kinetics for nitridation of silicon monocrystal has been carried out. According tothe theory for kinetics of reaction of vapour with solid phase a nitridation kinetic model, from which it can beshown thal the rate of nitridation reaction of silicon crystal should be controlled by three stage limiting factors,was proposed. These limiting factors are chemical reaction, chemical reaction mixed with diffusion and diffu-sion. Using this model to treat our experimental data, satisfactory correlation coefficient and apparentactivation energy of nitridation of p-type (lll) silicon crystal have been obtained. The nitride film was identi'fied to be a-Si_3N_4 (Hexagonal, a=0.7758nm,c_o=0.5623nm) by X-ray diffraction analysis. Morphology ofthe nitride films formed in different nitridation duration was observed in both planar andcross-sectional viewsby SEM (scanning electron microscope).     

HSi80-3硅黄铜船用舵盖铸件精铸工艺的凝固模拟

运用Procast软件对HSi80-3硅黄铜船用舵盖零件在两种浇注工艺方案下的凝固过程进行模拟计算,在此基础上分析探讨了该铸件可能产生缩孔或缩松的部位。模拟显示第一种浇注工艺会在零件主体部位产生严重缩孔,而第二种浇注工艺则能自下而上顺序凝固,避免缩孔或缩松的产生,据此确定了第二种铸造工艺方案,并采用试验进行验证。结果表明,此浇注工艺没有产生技术要求缺陷,证明了凝固模拟的可行性。     

Preparation and characterization of biomorphic SiC hollow fibers from wood by chemical vapor infiltration

Biomorphic SiC hollow fibers were prepared by the reactive infiltration of SiO vapor into basswood-derived charcoal. Gaseous SiO was produced from a SiO₂/Si powder mixture in Ar at elevated temperatures. Scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and Fourier transform-infrared spectroscopy were employed to characterize the structural morphology and phase compositions of the final products. The results show that the tubular cells in bulk charcoal are converted into lots of SiC hollow fibers with pore diameters of 10–50 μm and lengths ranging from hundreds of μm to several mm. Resulting SiC hollow fibers consist of β-SiC with a minute amount of α-SiC. The formation mechanism of SiC hollow fibers is based on the gas–solid reaction between SiO and carbon.     

Probability of precision micro-machining of insulating Si3N4 ceramics by EDM

Electrical discharge machining (EDM) is used as a precision machining method for the electrically conductive hard materials with a soft electrode material. But recently we succeeded to machine on insulating material by EDM. The technology is named as an assisting electrode method. The EDMed surface is covered with the electrical conductive layer during discharge. The layer holds the electrical conductivity during discharge. For micro-EDM, the wear of tool electrode becomes lager ratio than the normal machining. So the micro-machining is extremely difficult to get the precision sample.

In this paper to obtain a fine and precise ceramics sample, some trials were carried out considering the EDM conditions, tool electrodes material and assisting electrode materials. Insulating Si₃N₄ ceramics were used for workpiece. The machining properties were estimated by the removal rate and tool wear ratio. To confirm the change of micro-machining process, the discharge waveforms were observed. The micro-machining of the Ø0.05 mm hole could be machined with the commercial sinking electrical discharge machine.     

多晶硅的真空感应熔炼及定向凝固研究

以工业硅为原料进行了多晶硅的真空感应熔炼及定向凝固研究，用自行设计的真空定向凝固设备制备了多晶硅铸锭。金相显微镜观察显示铸锭的显微组织为粗大的柱状晶，经电感耦合等离子体发射光谱仪分析，其纯度由99．50％提高到99．86％，各种杂质含量都有所减少。     

镁合金中硅的加入方法研究

研究硅以块状、粉状和铝-硅中间合金形式加入镁合金时的优缺点.结果表明,硅以粉状形式加入镁合金时,硅的吸收率达80%左右,而以铝-硅中间合金形式加入时,工艺简便,镁液质量较高,吸收率达70%左右.且硅以粉状形式加入镁合金时,形成的Mg2Si相尺寸较小,合金的基体晶粒较细.     

Studies on electric-discharge machining of non-contact seal face grooves

In this paper, the electric-discharge machining (EDM) of non-contact seal grooves was studied. Two types of material, namely: tungsten carbide and silicon carbide were tested by EDM due to their hard machining behaviors. The geometry of seal grooves is another reason why grinding or other precision machining processes cannot be applied. Four parameters of EDM processes were studied, namely: electrode material, pulse duration, discharge current, and polarity. According to experimental results, the optimal process parameters were obtained based on the specimen’s qualities, such as surface roughness and depth of cut. An industrial example was also studied in the final stage of the proposed paper.