MgO-CaO-TiO2系材料的烧结性能及抗水化性能

以白云石、工业钛白粉、轻烧镁砂为原料配制了不同组成的MgO-CaO-TiO2材料,分别于1500℃、1550℃、1600℃、1650℃保温3 h煅烧后,研究了材料的烧结性能,并采用蒸压法(0.1 MPa下蒸压2 h)研究了烧后试样的抗水化性能.研究结果表明1550～1600℃煅烧后,试样均达到了良好的烧结,相对密度达到92%以上,原始配料中的CaO全部转化成了不易水化的CaO·TiO2,因而所有试样均表现出优良的抗水化性能.     

空气气氛中烧成Si3N4-SiC复合材料的性能、相组成和显微结构

以氮化硅细粉(粒度＜0.088 mm,w(β-Si3N4)＞95%)、碳化硅(w(SiC)＞98%,粒度分别为2.8～0.9mm、0.9～0.15 mm、＜0.115 mm和＜0.063 mm四级)、硅粉(粒度＜0.045 mm,w(Si)＞98%)和硅灰(w(SiO2)=98.3%)为原料,以木质素磺酸钙水溶液作成型结合剂,采用150 MPa的压力成型为65 mm×114 mm×230mm的Si3N4-SiC、Si3N4-SiC-Si和Si3N4-SiC-SiO2三种试样.在空气气氛中,以50℃·h-1的升温速度升至800℃保温4 h,再升至1450℃保温2 h,自然冷却至室温后,测定烧成后试样的常温耐压强度、常温抗折强度、1400℃下的高温抗折强度、显气孔率、体积密度和残氮率,并采用XRD、SEM和EPMA等手段分析烧后试样的相组成和显微结构.结果表明3种试样在空气气氛中烧成后的高温(1400℃)和常温抗折强度都比较高,显气孔率都比较低,而耐压强度则以Si3N4-SiC试样的最高;烧成后试样中心区域的残氮率以Si3N4-SiC-Si试样的最高,Si3N4-SiC-SiO2试样的次之,Si3N4-SiC试样的最小;在空气气氛中烧成后,Si3N4-SiC试样中的Si3N4分解较多,SiC-Si3 N4-Si试样的表面和内部都明显含有单质Si,SiC-Si3N4-SiO2试样表面区域的Si2N2O晶体发育很好,而内部区域的晶体发育较小.     

Na_2O－ZnO－CaO－Al_2O_3－SiO_2烧结微晶玻璃的试制

Ｎａ＿２Ｏ－ＺｎＯ－ＣａＯ－Ａｌ＿２Ｏ＿３－ＳｉＯ＿２烧结微晶玻璃的试制刘世权，许淑惠，袁怡松，杨晓晶（西北轻工业学院７１２０８１）ＳｉｎｔｅｒｅｄＮａ＿２Ｏ－ＺｎＯ－ＣａＯ－Ａｌ＿２Ｏ＿３－ＳｉＯ＿２ＧｌａｓｓＣｅｒａｍｉｃｓ￥ＬｉｕＳｈｉｑｕａｎ...     

Application of pulse discharge sintering (PDS) technique to rapid synthesis of Ti3SiC2 from Ti/Si/C powders

To synthesize Ti₃SiC₂ samples, pulse discharge sintering (PDS) technique was utilized to sinter elemental powders of Ti/Si/C with stoichiometric and off-stoichiometric ratios in a temperature range of 1200–1500 °C. The results showed that high purity Ti₃SiC₂ could not be obtained from the Ti/Si/C powder with molar ratio of 3:1:2, and Ti₃SiC₂ preferred to form at relatively low sintering temperature for a short time. When 5Ti/2Si/3C and 3Ti/1.5Si/2C powders were sintered for 15 min, the TiC content was respectively decreased to 6.4 and 10 wt.% at 1250–1300 °C. The corresponding relative density of the samples sintered from 5Ti/2Si/3C powder was calculated to be as high as 99% at the temperature above 1300 °C. It is suggested that low-temperature rapid synthesis of Ti₃SiC₂ would be possible through the PDS technique, provided that the composition of the starting powders should be adjusted to be off-stoichiometric ratio from 3:1:2.     

Effect of ZnO and TiO2 doping on the sintering behavior of Y2O3 ceramics

Full densification of Y₂O₃ is challenging and requires a very high sintering temperature (above 1700 °C). In this study, the effect of ZnO and TiO₂ dopants on its densification was investigated, showing that both dopants lowered the sintering temperature and improved the process. Moreover, ZnO promoted the grain growth, while TiO₂ inhibited it; hence, the ZnOTiO₂ co-doping and the change in the ZnO/TiO₂ ratio allowed the control of the sintered body microstructure while maintaining high densification. Since Y₂O₃ has a higher plasma erosion resistance than conventional Si-based materials, the plasma dry etching resistance of the sintered Y₂O₃ was also evaluated and found superior due to the improved densification and controlled grain size of the doped samples.     

Sintering behaviour of La1−xSrxFeO3−δ mixed conductors

The sintering properties of La_1−xSr_xFeO_3−δ (x = 0.1, 0.25) mixed conductors have been investigated with particular emphasis on the effect of secondary phases due to cation non-stoichiometry (±5 mol% La excess and deficiency). Secondary phases, located at grain boundaries in cation non-stoichiometric materials, increased the sintering temperature compared to single-phase materials. Extensive swelling in final stage of sintering was observed in all materials, which resulted in micro-porous materials. The swelling was most pronounced in the phase pure and two-phase materials due to La-deficiency, while refractory secondary phases in La-excess materials inhibited both sintering, grain growth and swelling. In La-deficient materials, formation of molten secondary phases resulted in rapid swelling due to viscous flow. The present findings demonstrated the importance of controlling sintering temperature and time, as well as careful control of the cation stoichiometry of La_1−xSr_xFeO_3−δ in order to achieve fully dense and homogenous La_1−xSr_xFeO_3−δ ceramics.     

铝硅比对白云鄂博铁精矿烧结液相流动性的影响

运用红外线微型烧结法对白云鄂博铁精矿烧结液相流动特性进行研究。通过在烧结原料中添加纯化学试剂研究不同Al2O3与SiO2含量之比对烧结液相流动性的影响。结果表明,Al2O3含量的增加虽然促进了烧结液相量的增多,但同时提高了液相的粘度,随着铝硅比的增加烧结试样的液相流动性降低。通过对试样气孔大小的对比,揭示了烧结过程中气孔形成与烧结矿液相流动特性的关系,粘度是控制气孔形成的重要因素。气孔的形成过程伴随着液相在气孔壁上的物理化学反应,气孔直径减小使烧结试样液相流动性变差。     

Effect of MgO sintering additive on mullite structures manufactured by fused deposition modeling (FDM) technology

An optimized recipe for 3D printing of Mullite-based structures was used to investigate the effect of MgO sintering additive on the processing stages and final ceramic properties. To achieve dense 3:2 mullite, ceramic filaments were prepared based on an alumina powder, a methyl silicone resin, EVA elastomeric binder and MgO powder. Using 1 wt% MgO and a dwell time of 5 h at 1600 °C, a dense mullite structure could be obtained from filaments with a diameter of 1.75 mm. Ceramic structures with and without sintering additive were printed in vertical and horizontal direction, to investigate the effect of printing direction on mechanical strength after sintering. Using four-point bending test, it was demonstrated that by using MgO, the printing orientation did not affect the mechanical strength significantly anymore. The low Weibull modulus could be explained by the closed porosity that emerge during the degassing of the preceramic polymer due to cross-linking.     

常压混合脱硅工艺生产种分精液

本文介绍了碳分、种分工艺对精液硅量指数A/S的不同要求,认为种分精液单独生产是很有必要的.本文从理论上分析了目前所应用的脱硅工艺,提出了一种常压生产种分精液的方法-常压混合脱硅工艺,并对某厂采用此工艺进行种分精液生产的情况进行了简单的介绍.     

高速钢表面硬质合金覆层的组织及性能

通过热喷涂-真空粉末烧结的方法在高速钢表面制备硬质合金覆层，分析了硬质合金覆层组织和界面结构的特点、测试了硬质合金覆层的结合强度、硬度和耐磨性。结果表明，热喷涂后经过1200℃烧结，获得1—3mm厚度的硬质合金覆层，结合强度达到450MPa，硬度达到85HRA，具有较高的耐磨性能。