电镀塑料制品对结构设计及成形工艺的要求

为保证电镀塑料制品的质量,提出了符合电镀要求的塑料制品设计原则,并且指出在注塑成形时,对塑料经过充分干燥,采用较高的注塑温度,较低的注射压力和较慢的注射速度,是使镀层获得良好结合强度的先决条件。     

Memory effects of all‐solution‐processed oxide thin‐film transistors using ZnO nanoparticles

Abstract— Non‐volatile memory effects of an all‐solution‐processed oxide thin‐film transistor (TFT) with ZnO nanoparticles (NPs) as the charge‐trapping layer are reported. The device was fabricated by using a soluble MgInZnO active channel on a ZrHfO^x gate dielectric. ZnO NPs were used as the charge‐trapping site at the gate‐insulator—channel interface, and Al was used for source and drain electrodes. Transfer characteristics of the device showed a large clockwise hysteresis, which can be used to demonstrate its memory function due to electron trapping in the ZnO NP charge‐trapping layer. This memory effect has the potential to be utilized as a memory application on displays and disposable electronics.     

一种可行的可用性测试过程

文章综述用户模型法、用户调查法、专家评审法和观察法4类可用性测试方法,根据可用性测试的经验,总结出一套合理实用的可用性测试过程,使得可用性测试的效率高、代价低,尽可能发现更多的可用性问题;提出在程序设计类课程的教学中,应适当向学生介绍可用性测试的方法和过程,以培养学生对自己开发的软件系统进行可用性测试的能力。     

Stochastic differential equations driven by a Wiener process and fractional Brownian motion: Convergence in Besov space with respect to a parameter

A stochastic differential equation involving both a Wiener process and fractional Brownian motion, with nonhomogeneous coefficients and random initial condition, is considered. The coefficients and initial condition depend on a parameter. The assumptions on the coefficients and the initial condition supplying continuous dependence of the solution on a parameter, with respect to the Besov space norm, are established.     

MEMS AC voltage reference for miniaturized instrumentation and metrology

This work explores MEMS (Micro-Electro-Mechanical Systems) potentialities to fabricate AC voltage references through mechanical-electrical transduction that could be used for high precision electrical metrology and for applications in miniaturized instrumentation. AC voltage reference ranging from 5 V to 90 V have been designed and fabricated using the same Epitaxial Silicon On Insulator (SOI) surface micromachining process allowing an accurate control of both dimensions and material properties. The measured MEMS AC voltage reference values have been found in a good agreement with CoventorWare calculations. These tests structures have also been used to develop the read-out electronics to drive the MEMS.     

Optimal replacement policy for a two-dissimilar-component cold standby system with different repair actions

In this paper, a cold standby repairable system consisting of two dissimilar components and one repairman is studied. When failures occur, the repair of both component 1 and component 2 are not ‘as good as new’. The consecutive operating times of component 1 after repair constitute a decreasing geometric process, while the repair times of component 1 are independent and identically distributed. For component 2, its failure is rectified by minimal repair, and the repair time is negligible. Component 1 has priority in use when both components are good. The replacement policy N is based on the failure number of component 1. Under policy N, we derive the explicit expression of the long-run average cost rate C(N) as well as the average number of repairs of component 2 before the system replaced. The optimal replacement policy N*, which minimises the long-run average cost rate C(N), is obtained theoretically. If the failure rate r(t) of component 2 is increasing, the existence and uniqueness of the optimal policy N* is also proved. Finally, a numerical example is given to validate the developed theoretical model. Some sensitivity analyses are provided to show the influence of some parameters, such as the costs for replacement and repair, and the parameters of the lifetime and repair time distributions of both components, to the optimal replacement policy N* and corresponding average cost rate C(N*).     

合成氨工艺参数优化技术开发及应用

以氨净值为响应值,影响响应值的17个过程参数为变量,经逐步回归选入触媒温度左3,触媒温度左4,循环CH_4%,H/N,NH_3%(进口)5个过程参数建立预测方程,并根据该方程对响应值的拟合结果和误差分布对样本进行分类。在此基础上,采取图形显示技术和统计分析的方法对分类样本集的过程参数进行比对分析,由此获取优类信息制订优化的工艺参数方案,经仿真验证后用于指导合成氨装置的生产试验。试验结果与试验前的对照期比较,氨净值均值由13.86提高到14.54,吨氨气耗减少15.9887m~3,吨氨电耗减少15.8kWh,节能效益十分明显     

Re-engineering of the design process for concurrent engineering

According to the requirements of concurrent engineering, three interdependency relationships (uncoupled relationship, coupled relationship and decoupled relationship) between design activities are presented in this paper. And the coupled relationship plays an important role in concurrent product design process. To represent the precedence relationships among design activities, a directed graph is used to describe the design process. And the interdependency relationship between activities is illustrated by a Design Structure Matrix which is the transpose of the accessibility matrix of the corresponding graph. Using the DSM, an algorithm of recognizing the coupled activities during the design process is presented. Moreover, an algorithm to figure out the order levels of activities during the design process is proposed. And both algorithms are illustrated with a die design example.