从PZT体系看无铅压电陶瓷的可能应用

总结了主要以(Bi0.5Na0.5)TiO3和NaNbO3为基的无铅压电陶瓷的性能，以Pb(Ti，Zr)TiO3基二元系、三元系压电陶瓷的性能与应用为参考，分析了无铅压电陶瓷可能的器件应用。此外，还对拓宽无铅压电陶瓷应用需要改进的性能提出了建议。     

机械力化学作用对低介硅灰石瓷料的相变和相组成的影响

采用X射线衍射仪(XRD)、差热分析(DTA)手段详细研究了由氧化物粉末制备硅灰石陶瓷时,机械力化学作用及后续热处理对硅灰石陶瓷相组成和相变过程的影响,分析了机械力化学在球磨过程中的作用机理主要是细化晶粒、使晶格畸变、晶格缺陷增多、非晶化和诱导低温化学反应。结果表明:高能球磨中的机械力化学作用能够有效地降低硅灰石陶瓷的烧成温度(11160~11220℃)。探明了经高能球磨的样品在烧成过程中的晶相转变规律。瓷料最终的晶相为单一的-硅灰石(高温变体)。     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

Ca掺杂钨镁酸铅陶瓷材料的制备及其介电性能

研究了Ca掺杂钨镁酸铅(PMW)陶瓷材料的合成、结构、烧结以及介电性能。结果发现：在Ca^2 摩尔分数小于15％时，能形成单相的PCMW钙铁矿相，结构由原来的斜方相向立方相转变。用二步合成法制备的样品容易致密烧结，气孔率比一步法制备的样品小。Ca的加入降低了材料的介电损耗，在频率为1MHz时，介质损耗达到了10^-4。当Ca^2 摩尔分数大于10％时，材料的Curie峰宽化显著，介电常数温度系数降低。     

新产品研发是建陶企业可持续发展的核心

新世纪我国建陶企业在整个国民经济的带动下将进一步发展，入世后经济全球化的市场竞争格局，建陶企业只有走新产口研发之路，严格企业管理，才会在日趋激烈的市场竞争中得以生存和可持续发展。     

用于高频谐振器的PbTiO_3基压电陶瓷

传统的PZT压电陶瓷的相对介电常数较大,一般为1 000以上,用于高频谐振器不易与线路匹配;而PbTiO3基压电陶瓷的相对介电常数较小,一般仅为200左右,对于10 MHz以上频率的谐振器,用PbTiO3基压电陶瓷作为压电振子是最佳的选择。本文主要研究用于高频谐振器的MnO2和Nd2O3改性PbTiO3基压电陶瓷的性质。PbTiO3基压电陶瓷的性质的改善是与此种陶瓷的制备工艺,显微结构和电导机制紧密相关的。     

烟气轮机特殊状态下的保护

从烟气轮机超速的极限开始 ,分别按照阀门的关闭时间为 1 .5s和 6s的两种典型状态 ,对烟机在联轴节断裂等特殊工况下的超速情况进行了分析。最后 ,对烟气轮机在特殊工况下的保护提出了建议。     

BaFe12O19/SiO2-B2O3微晶玻璃陶瓷的制备和微波性能

采用柠檬酸sol-gel工艺合成了BaFe12O19/SiO2-B2O3微晶玻璃陶瓷，研究了SiO2-B2O3玻璃的含量，Ba/Fe原子比和热处理温度对体系析出晶相的影响，以及介电常数和磁异率在1MHz-6GHz频率范围的变化规律，结果表明，休系中SiO2-B2O3玻璃的含量和Ba/Fe比越高，BaF312O19相的析出越困难，前驱体合适的热处理温度为1000℃，介电常数和磁导率基本上随测试频率的增而加下降；介电损耗的最大值为0．43，磁损耗较小。     

功率电子器件用AlN陶瓷基板的研制

阐述了AlN陶瓷的烧结原理 ,分析了烧结工艺参数对大面积AlN基板性能的影响 ,成功研制出了高热导率(190W /m·K)、大面积 (14 0mm× 90mm)、翘曲度为 2 0 μm/5 0mm的AlN陶瓷基板。     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.