Catalytic Hydrocracking of a Bitumen‐Derived Asphaltene over NiMo/γ‐Al2O3 at Various Temperatures

Hydrocracking of a bitumen‐derived asphaltene over NiMo/γ‐Al₂O₃ was investigated in a microbatch reactor at varying temperatures. The molar kinetics of asphaltene cracking reaction was examined by fitting the experimental data. Below a defined temperature, the molar reaction showed the first‐order kinetic feature while at higher temperatures secondary reactions such as coke formation became significant, causing deviation of the reaction behavior from the proposed first‐order kinetic model. Selectivity analysis proved that dominant products varied from gases to liquids to gases with increasing temperature, shifting the dominant reaction from C–S bonds cleavage to C–C bonds cleavage.     

Elucidation of colour development and microstructural characteristics of Allium sativum fumigated with acetic acid

It has been well known that the greening of Allium sativum cloves could be formed after immersed in acetic acid solution. Nonetheless, no investigation was reported on colour development of A. sativum in response to acetic acid vapour until now. In this study, the brief exposure of A. sativum to acetic acid vapour (200–400 ppm) was combined with controlled atmosphere (5%, 20% and 80% CO₂) packaging storage to break cell membrane and green garlic. The garlic bulbs were fumigated with acetic acid before controlled CO₂ atmosphere packaging for 25 days at 4 °C. Fumigation with 200 ppm acetic acid followed by high CO₂ atmosphere packaging (80% CO₂) facilitated the garlic greening. It was also verified that γ‐glutamyl transpeptidase was involved in garlic greening in present study, and the compromise of glacial acetic acid vapour fumigation and CO₂ gas atmosphere in package stored at low temperature could result in garlic greening as well.     

Fluorene-centered perylene monoimides as potential non-fullerene acceptor in organic solar cells

A fluorene-centered perylene monoimide dimer, PMI-F-PMI with a partly non-coplanar configuration has been developed as a potential non-fullerene acceptor for organic solar cells (OSCs). The optimum power conversion efficiency (PCE) of the OSC based on PMI-F-PMI as acceptor and poly (3-hexyl thiophene) (P3HT) as donor is up to 2.30% after annealing at 150 °C. The PCE of 2.30% is the highest value for the OSCs based on P3HT donor and non-fullerene acceptor lies in that PMI-F-PMI’s lowest unoccupied molecular orbital (LUMO) level around −3.50 eV matches well with the donor P3HT to produce higher open-circuit voltage (V_oc) of 0.98 V. Meanwhile, PMI-F-PMI makes remarkable contribution to devices’ light absorption as the maximum EQE (30%) of the devices is at 512 nm, same to the maximum absorption wavelength of PMI-F-PMI. The other favorable characteristics of PMI-F-PMI in bulk heterojunction (BHJ) active layers is proved through the photo current density measures, the relatively balanced electron–hole transport, and the smooth morphology with root mean square (RMS) value of 1.86 nm. For these advantages, PMI-F-PMI overwhelms its sister PMI-F and parent PMI as an acceptor in BHJ solar cells.     

Polymer derived ceramic materials from Si,B and MoSiB filler-loaded perhydropolysilazane precursor for oxidation protection

Silica-based coating systems were developed using polymer derived ceramics (PDCs) technology. Ceramic composites on the base of a SiO₂ and SiNO matrix and homogeneously distributed Mo₅SiB₂, SiB₆, Si and B fillers were manufactured. The coating systems have low porosity and provide a high oxidation resistance up to 100 h at 800 °C and 1100 °C in air. The influence of temperature and atmosphere of pyrolysis on the polymer precursor, the volume fraction of filler materials on the chemical composition of compacts as well as their high-temperature oxidation protection was investigated.     

Structural dependence of microwave dielectric properties of spinel structured Mg2(Ti1-xSnx)O4 solid solutions: Crystal structure refinement,Raman spectra study and complex chemical bond theory

Mg₂(Ti_1-xSn_x)O₄ (x?=?0–1) ceramics were prepared through conventional solid-state method. This paper focused on the dependence of microwave dielectric properties on crystal structural characteristics via crystal structure refinement, Raman spectra study and complex chemical bond theory. XRD spectrums delineated the phase information of a spinel structure, and structural characteristic of these compositions were achieved with the help of Rietveld refinements. Raman spectrums were used to depict the correlations between vibrational phonon modes and dielectric properties. The variation of permittivity is ascribed to the Mg₂(Ti_1-xSn_x)O₄ average bond covalency. The relationship among the B-site octahedral bond energy, tetrahedral bond energy and temperature coefficient are discussed by defining on the change rate of bond energy and the contribution rate of octahedral bond energy. The quality factor is affected by systematic total lattice energy, and the research of XPS patterns illustrated that oxygen vacancies can be effectively restrained in rich oxygen sintering process. Obviously, the microwave dielectric properties of Mg₂(Ti_1-xSn_x)O₄ compounds were obtained (${\epsilon }_r$= 12.18, $Q\times f$?=?170,130?GHz, ${\tau }_f$?=??53.1?ppm/°C, x?=?0.2).     

An approach to measure infill matric suction of irregular infilled rock joints under constant normal stiffness shearing

Rock joints infilled with sediments can strongly influence the strength of rock mass. As infilled joints often exist under unsaturated condition, this study investigated the influence of matric suction of infill on the overall joint shear strength. A novel technique that allows direct measurement of matric suction of infill using high capacity tensiometers (HCTs) during direct shear of infilled joints under constant normal stiffness (CNS) is described. The CNS apparatus was modified to accommodate the HCT and the procedure is explained in detail. Joint specimens were simulated by gypsum plaster using three-dimensional (3D) printed surface moulds, and filled with kaolin and sand mixture prepared at different water contents. Shear behaviours of both planar infilled joints and rough joints having joint roughness coefficients (JRCs) of 8–10 and 18–20 with the ratios of infill thickness to asperity height (t/a) equal to 0.5 were investigated. Matric suction shows predominantly unimodal behaviour during shearing of both planar and rough joints, which is closely associated with the variation of unloading rate and volumetric changes of the infill material. As expected, two-peak behaviour was observed for the rough joints and both peaks increased with the increase of infill matric suction. The results suggest that the contribution of matric suction of infill on the joint peak normalised shear stress is relatively independent of the joint roughness.     

Research on hydrophobicity of electrospun Fe3O4/PVDF nanofiber membranes under different preparation conditions

Abstract

Preparation condition can affect the structure and the properties of nanofiber membrane. In order to explore suitable conditions to prepare the Fe₃O₄/PVDF nanofiber membrane with good hydrophobicity, the hydrophobicity of Fe₃O₄/PVDF nanofiber membranes obtained by electrospinning was investigated by changing preparation conditions like weight percentage of Fe₃O₄ nanoparticles, blending quality concentration of poly (vinylidene fluoride) (PVDF) and Fe₃O₄ nanoparticles, and positive voltage. And the variations of hydrophobicity of Fe₃O₄/PVDF nanofiber membranes modified by 1H, 1H, 2H, 2H-perfluorodecyl trimethoxysilane were studied. The results show that the hydrophobicity of Fe₃O₄/PVDF nanofiber membranes has changed under different preparation conditions. The contact angles of samples increased after a modification by 1H, 1H, 2H, 2H-perfluorodecyl trimethoxysilane, which indicates that the hydrophobicity of Fe₃O₄/PVDF nanofiber membranes has been enhanced.