一起氧气瓶燃割事故分析

20 0 2年 5月 30日晚 7:5 5 ,徐州市工程集团某机械厂下料车间 ,氧气汇流排中一只即将开启使用的氧气瓶发生燃烧击穿事故 ,造成一死一伤的严重后果。事故发生的第二天笔者被特邀赶到现场 ,会同调查组对事故的性质、原因进行分析鉴定 ,并通过了原因分析鉴定结论。为防止此类事故的再次发生 ,引起充装或使用单位的足够重视 ,从中吸取教训 ,把事故消灭在萌芽状态 ,减少不必要的损失 ,现将这起氧气瓶燃割事故介绍如下。1　钢瓶及汇流排的原始情况钢瓶为河北涿鹿高压气瓶制造厂生产 ,气瓶原始数据如下 :气瓶编号 0 85 15 ,水压试验TP2 2 5 ,工…     

Determination of the content of wax esters in some sea foods and their molecular composition. A comparison with ω-3 enriched wax esters

Wax esters enriched in ω-3 fatty acids have been recently shown to be readily absorbed by rats after dietary supplementation. Wax esters are less prone to oxidation and can be better formulated than liquid ω-3 derivatives. All these characteristics suggest a possible use of wax esters enriched in ω-3 as food supplements. However, some naturally occurring wax esters are defined as scarcely digestible (jojoba oil, spermaceti). On the other hand, wax esters have been found in several sources of marine origin, which can enter normal foodstuff. In order to better understand the digestibility of wax esters, we have analysed some foods from marine sources. The content of triglycerides and wax esters of the foods has been determined. Moreover, wax esters have been analysed for their composition in alcohols and fatty acids. Wax esters have been shown to be a part of the neutral lipid extract of the foods analysed. Their content, if compared with the content in triglycerides, shows striking differences. In the case of two botargo preparations, it has been shown that wax esters are more than 90% of the total neutral lipid extract. The content of fatty acids and alcohols found in the foods analysed is consistent with published data.     

Prediction of the effects on dynamic response due to distributed structural modification with additional degrees of freedom

The aim of this study is to investigate means of efficiently assessing the effects of distributed structural modification on the dynamic properties of a complex structure. The dynamic properties of the modified structure can be determined by experimental testing or numerical simulation, both of which are complex, expensive and time-consuming. Assuming that the original dynamic characteristics are already established and that the modification is a relatively simple attachment, the modified dynamic properties may be determined numerically without solving the equations of motion of the full-modified structure. The frequency response functions (FRFs) of the modified structure can be computed by coupling the original FRFs and a delta dynamic stiffness matrix for the modification introduced. The validity of this approach is investigated by applying it to a cantilever beam to which a smaller beam is attached as modification. The original FRFs were obtained experimentally as well as numerically. The delta dynamic stiffness matrix was determined numerically by modeling the attachment and part of the original structure including the attachment points. The FRFs of the modified beam were then computed. Good agreement is obtained by comparing the results to the FRFs of the modified beam determined experimentally as well as by numerical modeling of the complete modified structure.     

MC^2电缆介质结构及阻抗分析

本文将用数学和实验两种方法证实MC～2电缆不仅能保证特性阻抗变化不超出电缆技术规范。而且能保证在设计频率范围内电缆结构反射损耗最小。     

化学镀Ni—P镀层的X射线衍射研究

根据X射线衍射分析结果,对化学镀高P(含P>11wt％或19at％)Ni-P镀层加热时效时,镀层成分和加热温度对结构转变的影响作了研究,结果表明,高P共晶、过共晶(含P>11wt％或19at％)合金的结构转变有如下特征:(1)相同加热时效条件下,Ni-P合金的结构转变与成分有密切关系:(2)对同一成分的过共晶合金,Ni-P合金的结构转变与时效温度密切相关;(3)过共晶合金在290～360℃温度范围内时效处理,出现Ni_xP_y介稳相,X射线衍射分析认为Ni_xP_y为Ni_(12)P_5。     

X荧光光谱法测定不锈钢的研究

本文论述了Ｘ荧光光谱测定高铬钢和不锈钢的分析方法，用理论α系数校正基体效应和用谱线干扰系数Ｌ校正谱线重叠影响。方法准确度和精度令人满意，操作十分简便、快速。     

摇臂参数设计方法

建立了中小功率内燃机常用摇臂参数化设计模型。采用可变参数构成摇臂结构，并作结构的有限元网络，此后再进行有限元分析，计算出摇的质量、刚度、转动惯量 力。使摇臂的设计归结为几个主要参数的优选。实例分析表明，计算值和实测值基本相符，优选出的摇避设计优于原设计。     

K202A压缩机电机轴瓦超温的原因及对策

K202A压缩机的电机轴瓦采用的是动压轴承,经常持续升温。其主要原因是由于滑动轴承和轴之间是半液体摩擦,润滑油在轴颈及轴瓦之间没有形成具有足够压力的油膜,造成滑动轴承和轴局部形成半液体摩擦而产生大量的热量,又无法被带走引起的。文章通过验算K202压缩机电机滑动轴承温度,分析影响滑动轴承运行温度的因素,提出在原滑动轴承上开油楔及加装一台齿轮油泵为滑动轴承强制润滑,并且通过联轴器把电机和压缩机连接起来,用压缩机轴瓦托起电机轴,使电机轴颈和轴瓦之间处于液体摩擦状态,可有效地降低滑动轴承的运行温度。     

Networks for sorting multitonic sequences

Lee and Batcher have designed networks that efficiently merge k separately provided sorted sequences of known lengths totalling n. We show that the design is still possible, and in fact easier to describe, if we do not make use of the lengths, or even the directions of monotonicity, of the individual sequences—the sequences can be provided in a single undelimited concatenation of length n. The depth of the simplest resulting network to sort sequences that are “k-tonic” and of length n is , generalizing Batcher's 1968 results for the extreme values of k (k=2 corresponding to merging, and k=n/2 corresponding to general sorting).The exposition is self-contained and can serve even as an introduction to sorting networks and Batcher's results.     

Twinning of YBa2Cu3O7 thin films on different substrates

The twinning of YBa₂Cu₃O₇ (YBCO) thin films with c-axis orientation on (001) MgO, (001) SrTiO₃, (012) LaAlO₃, (110) NdGaO₃ and (001) NdGaO₃ substrates, prepared by laser ablation, has been examined using a combination of and θ/2θ scans at a four-circle diffractometer. On all substrates, except for (001) NdGaO₃, the tetragonal to orthorhombal phase transition results in four different orientations of YBCO twins relating to the substrate. On (001) NdGaO₃ only two different twin orientations, accompanied by a slight lattice monoclinization, has been observed.