强冷磨削的试验研究

进行了强冷磨削和干磨削试验。试验结果表明 ,磨削温度随工件速度和磨削深度的增大而增大 ,强冷磨削可显著降低磨削温度 ,在冷却压力小于 1MPa时 ,外冷却的冷却效果优于内冷却     

A kinetic model for polystyrene (PS) pyrolysis reaction

A mathematical model for the pyrolysis reaction of polystyrene (PS) in a semi-batch reactor has been presented. The thermal degradation of PS was flexibly modeled by a combination of random and specific chain-end scissions. Numerical simulation was used to investigate the effect of operating conditions on the PS products spectrum, the results of which were validated by the experimental data. It was found that as the reaction temperature increased (decreased), the monomer fraction in the products became lower (higher) while the trimer higher (lower). No significant variation in the product composition was, however, observed while constant temperature was maintained. These results indicate the reaction temperature is an effective manipulated variable for the control of products composition of PS pyrolysis. The calculation of the optimum temperature trajectories through the optimization study can thus be of interest for achieving productivity enhancement in plastics pyrolysis processes. This paper is dedicated to Professor Dong Sup Doh on the occasion of his retirement from Korea University.     

Pt-V2O5-WO3/TiO2 catalysts supported on SiC filter for NO reduction at low temperature

The catalytic filter, V₂O₅-WO₃-TiO₂ supported on a ceramic filter, is known as a promising material for treating particulates and NO _x simultaneously at optimum temperatures around 320°C. In order to improve its catalytic activity at low temperatures, the effect of Pt addition on the catalytic filter has been investigated. Catalytic filters, Pt-V₂O₅-WO₃-TiO₂/SiC, were prepared by co-impregnation of Pt, V, and W precursors on TiO₂ coated-SiC filter by vacuum aided-dip coating. The Pt-added catalytic filter shifted the optimum working temperature from 280–330°C (for the non Pt-impregnated filter) to 180–230°C, providing N _x slip concentration less than 20 ppm for the treatment of 700 ppm NO at a face velocity of 2 cm/s with the same value over the non Pt-added catalytic filters. The promotional effect following the addition of Pt is believed to result from electrical modification of the catalyst maintaining a high electron transfer state. Ammonia oxidation was also observed to be dominant above the optimal temperature for SCR.     

不同因素对浸入式水口预热温度场的影响

运用大型有限元分析软件ANSYS的FLO TRANCFD模块对浸入式水口在抽风式预热烘烤方式下的瞬态传热过程及影响水口预热温度场的各种因素进行了研究 ,得到了该烘烤方式下水口预热后的温度场分布和水口的升温曲线。研究结果表明 :影响水口预热温度的最主要因素是抽风流量和烘烤箱的几何尺寸 ;适当提高抽风流量、减小烘烤箱的几何尺寸可以大大提高水口颈部的预热温度 ,从而降低浸入式水口的事故率     

基于神经网络技术的注塑成型注射压力和熔体温度预测

建立了基于径向基函数网络的注塑成型注射压力和熔体温度的预测模型，与BP神经网络模型和CAE结果进行了对比。结果表明，径向基函数网络在精度、训练速度等方面优于BP网络。     

The role of temperature in copper electrocrystallization in ammonia-chloride solutions

This paper presents the analysis of temperature effect on the copper electrocrystallization process from the stainless steel/Cu(II)-Cu(I)-NH₄Cl-NH₃-H₂O system. Electrochemical techniques and scanning electron microscopy with energy dispersion spectroscopy were employed. An increment in temperature had a favorable effect in increasing the kinetic and nucleation parameters, favoring the copper reduction on the stainless steel substrate. From the chronoamperometric study, it was possible to find the transfer coefficient (α), which does not have a significant variation with temperature, and the exchange current density (i₀) for different temperatures, where a 50.63 kJ/mol value was estimated for the activation energy. The potentiostatic study suggested the presence of two processes involved: an electron transfer reaction and a 3D nucleation—growth process, under combined charge transfer and diffusion limitations. In addition, an important current contribution could be accounted for on the basis of the existence of a capacitive component in the system. This capacitive behavior was associated to the oxide layer (Cr₂O₃)-chloride interactions on the stainless steel surface. Current transients analyses at different potentials, based on the models of: Milchev (low overpotential), Scharifker-Mostany (SM) and Heermann-Tarallo (HT) (high overpotential) allowed to obtain the values of nucleation parameters, such as: the nucleation rate constant (A), the active nucleation sites number (N₀), the stationary nucleation rate (I_st = A × N₀) and the nuclei saturation number (N_s). Finally, the deposits obtained were analyzed by SEM, showing an acceptable correlation between the nucleation parameters and morphology of the deposits obtained. An increment in temperature favored the growth of the cluster before the coalescence occurred.     

沈阳含蜡油稀释三榨脱蜡新工艺

本文研制出一种新型的含蜡油稀释三榨脱蜡新工艺,该工艺对加工沈北减二线含蜡油十分有效,提高了石蜡质量与产量。     

The Moisture Distribution of High Moisture Content Rough Rice During Harvesting, Storage, and Drying

The kernel moisture content (MC) distribution of five varieties of double season rice was tested during the process of harvesting, drying, and tempering. Significant kernel MC variance was found to exist within the panicle. Binodal kernel MC distribution frequency was found at harvest. The MC distribution of five varieties during harvesting and drying showed similar trend of uniformity. To investigate the mechanism of moisture transport among rice kernels under low temperature, the kernel MC distribution of rice planted in Northeastern China was also investigated after stacked for over one month under the temperature of -20°C. The moisture exchange among rice kernels was found greatly influenced by environmental factors.     

(1-x)NBT-xBaTiO3系陶瓷材料制备过程中烧成工艺制度的研究

选取BT6组成点,采用不同的预合成温度、烧结温度和保温时间制备样品,研究各样品的体积密度、线收缩率、晶粒发育状况和压电性能,确定最佳的烧成工艺制度。