Application of SiC-Si functionally gradient material to thermoelectric energy conversion device

Because of its high–temperature chemical stability, SiC ceramic is a promising material for high-temperature device applications such as thermoelectric energy converters. However, the electrical conductivity of SiC ceramic is too low for it to be used as a thermoelectric energy converter at the cold junction. Therefore, we propose a SiC-Si functionally gradient material (FGM) in order to improve the electrical conductivity of the SiC ceramic at the cold junction. An SiC rod was fired in a temperature gradient furnace. One end of the SiC rod was maintained at 2473 K and the other end was maintained at 1973 K for 30 min. After firing, the porous SiC edge fired at 1973 K was dipped into molten Si in order to infiltrate molten Si into the porous SiC. The microstructure of the FGM is classified into three regions: the SiC-Si composite material; the porous SiC ceramic; and the densified SiC ceramic. The electrical conductivity, the Seebeck coefficient and the thermal conductivity for each region of SiC-Si FGM was measured at 300 K; a figure of merit was calculated. The figure of merit of the SiC-Si FGM at the cold junction, at room temperature, was 10⁸ times higher than that of a nongradient SiC ceramic.     

Nonlinear coupled problems in dynamics of shells

The coupled system of three partial differential equations governing a flexible shallow shell dynamics is analysed. No any prior assumptions about the temperature distribution through the shell thickness are applied. The efficiency of the method used here when applied to the solution of integral-differential equations with different dimensions (three-dimensional equations related to the Kirchhoff-Love model) and of different type (heat transfer equations and the hyperbolic equations of shell theory) is demonstrated. Many computational results are reported and discussed.     

阀控式铅酸蓄电池的维护

对阀控式铅酸式蓄电池的维护工作进行了初步探讨。     

化学镀工艺在微电子材料中的研究和应用

简要综述了化学镀工艺在微电子材料中的应用,讨论了影响化学镀镍、铜、锡、钴和贵金属等的主要因素,阐述了化学镀微电子材料的特性、存在问题及研究动态。     

湿H2S环境中金属材料腐蚀的研究

介绍了在湿H2S环境中金属材料的腐蚀试验标准、方法和手段并重点强调了在H2S试验过程中常遇到的一些问题的处理方法.最后,指出了应加强H2S腐蚀的基础性和系统性研究的研究方向.     

用屏蔽暂堵技术封堵水平井裂缝性漏层

克拉玛依油田HW702水平井的大斜度段和水平段,将穿越纵向裂缝发育的二叠系佳木河组储层。为安全钻进和保护油层,用超细碳酸钙和磺化沥青复配后加入复合离子钻井液中成屏蔽暂堵的堵漏钻井液。室内用岩心试验,屏蔽暂堵后渗透率可降为0,暂堵深度小于3cm,可用酸化和射孔解堵。现场使用效果也很好,使HW702水平井顺利完钻,并获得工业油气流。     

Fabrication of sharp silicon tips employing anisotropic wet etching and reactive ion etching

We developed a process to obtain sharper silicon tips by employing anisotropic etching in a KOH solution followed by SF₆ plasma etch. The tips were further sharpened using the established thermal oxidation technique to decrease the cone angle and, therefore, obtain smaller curvature radii. We have analyzed the impact of such changes in geometry on a figure of merit associated with the field emission characteristics. An increase in the figure of merit by a factor of three was found in relation to the tips before sharpening.     

关于离子注入中温升的探讨

本文在理论和试验两个方面探讨了离子注入中的热效应和温升现象。注入样品的温升对离子注入层的性能有直接影响。分析了理论计算注入样品温升的一些情况。给出了实际测量注入样品温升的几种试验方法。阐明了控制注入样品温升的若干可能途径。     

对未来我国覆铜板业技术发展的战略与任务的探讨

对未来十年我国覆铜板业技术发展的战略与技术开发重点任务进行了探讨。