Substituted uracils as corrosion inhibitors for copper in 3% NaCl solution

Substituted uracils were tested as corrosion inhibitors of copper in 3% NaCl medium using electrochemical polarisation, impedance measurements and non-electrochemical techniques (weight loss, IR and UV-visible). This study permitted to follow the evolution of the inhibitory effect of the uracil derivatives, according to their substituents, on copper in 3% NaCl medium. Comparison of results showed that dithiouracil (DTUr) was the best inhibitor. The maximum inhibition efficiency reached 98% at 10⁻³ M. DTUr adsorbs on the copper surface according to the Frumkin isotherm model.     

Further evidence of responsibility of impurities in MgO for variability in its basicity and catalytic performance in oxidative coupling of methane

Further evidence was delivered that certain impurities, which could be contained in MgO samples, might be responsible for observed variability in MgO basicity and catalytic performance in oxidative coupling of methane. The surface basicity/base strength distribution of a series of MgO samples containing or not containing Ca and Na impurities was determined by a temperature-programmed desorption of CO₂. It was revealed that samples containing Ca and Na impurities have much more medium, strong and very strong basic sites. The surface basicity of MgO samples containing added alkali or alkaline earth compounds or water was characterized by a test reaction of transformation of 2-butanol. It was confirmed that the introduction of these compounds to a pure MgO enhanced both its basicity and activity in oxidative coupling of methane.     

纳米β-Ni(OH)2与球型Ni(OH)2的热性能比较研究

用配位沉淀法合成出纳米级Ni（OH）2，并对其进行XRD，TEM，DSC分析，分析结果表明，所得纳米β-Ni（OH）2为可用作电极材料的β-Ni（OH）2，粒径为30－40nm，且热分解温度比普通球镍低10℃左右，摩尔分解热比普通球镍低4－7kJ，从理论上分析了产生此现象的原因。     

Pressureless sintering and characterization of cordierite/ZrO2 composites

Cordierite/ZrO₂ composites with 5 to 25 wt% ZrO₂ were fabricated by conventional powder mixing and pressureless sintering method. Their densification behavior, microstructure, mechanical and thermal properties were studied. By dispersing 25 wt% (9.57 vol%) ZrO₂, densified cordierite/ZrO₂ composite with a relative density of 98.5% was obtained at an optimum sintering condition of 1440 °C and 2 h. ZrO₂ particles were homogenously dispersed within matrix grains and at the grain boundaries. The intragranular particles were finer than 100 nm and the intergranular particles were coarser. Both fracture strength and toughness could be enhanced more than two times higher, compare to those of monolithic cordierite, by dispersing 25 wt% ZrO₂ into the cordierite matrix. The toughening mechanism in the present composites was mainly attributed to martensitic transformation due to ZrO₂ dispersion. Electronic Publication     

Cu－MnO_2同槽电解半工业试验研究

提出了Ｃｕ－ＭｎＯ＿２同槽电解的新工艺，在同一电解槽同时得到电铜和电解二氧化锰两种产品，该新工艺具有低电耗、低酸雾污染和低酸耗等优点．     

Relationship between CO2 Sensor Voltage Response and Phase Equilibrium of Solid Electrolyte Na, K-β/β"-Al2O3

A type of CO2 sensor based on oxygen concentration cell was designed as following: Cell I: Pt | Au, O2,CO2|Na2CO3(Au)|NKBA(Au)|YSZ|O2, CO2|Pt or Cell Ⅱ: Pt|Au, O2, CO2|K2CO3(Au)|NKBA(Au)|YSZ|O2, CO2|Pt.(Na,K-β/β″-Al2O3 is named by NKBA). The sensor signal is consistent with the Nernstian slope within the region ofphase equilibrium for Na, K-β/β"-Al2O3 material. The relationship between CO2 sensor voltage response and phaseequilibrium of solid electrolyte Na, K-β/β-Al2O3 is discussed in this paper.     

SiC颗粒增强铝基复合材料切削表面分形维数及其与抗磨损性能的关系

做为一种耐磨性能很好的材料 ,SiC颗粒增强铝基复合材料切削加工表面具有分形特征。实际研究表明SiC颗粒增强铝基复合材料切削加工表面分形维数与抗磨损性能有密切关系 ,本文还分析了表面分形维数越大其抗磨损性能越强的机理。     

分割电极片状压电致动器——(二)位移特性及狭缝宽度对其影响的实验研究

研究了悬臂梁式分割电极片状压电致动器的位移特性。理论分析表明，分割电极狭缝宽度会减小致动器自由端的位移输出，但当狭缝宽度小于致动器电极宽度的１０％时，可忽略狭缝宽度的影响。致动器端部位移的测试结果大于理论计算值。与现有磁头悬浮臂尺寸相近的致动器，在２０Ｖ～５０Ｖ的电压驱动下均可获得１μｍ～２μｍ的致动位移。对９８５０道／厘米的密度磁盘，该位移能覆盖至少一个磁道宽度，满足磁头定位两级伺服系统对第二级致动器位移的基本要求。     

含H2S井完井液用除硫剂和缓蚀剂

含H_2S井完井液对井下金属管串具有腐蚀性。采用锌基或铁基螯合物除硫剂及咪唑啉缓蚀剂可有效地防止这种腐蚀的发生。本文对H_2S的腐蚀、除硫剂和缓蚀剂产品及其对产层的损害作了介绍与探讨。