发展中的数码喷墨用UV固化油墨

数码喷墨用UV固化油墨是一种新兴喷印技术,文章针对数码喷印技术、油墨成分及其油墨的相应要求进行了阐述,文中涉及了现有的成型产品,并对UV固化油墨的发展趋势进行了展望,有助于人们了解这项新技术和新产品.     

Effects Of Ozone On The Production Of Biodegradable Dissolved Organic Carbon (BDOC) During Water Treatment

This article deals with the oxidation effect of ozone on the increasing fraction of biodegradable organic matter with the “ozotest” method, a laboratory technique which simulates the effect of ozonation and allows a complete oxidation assessment. Ozone treatment was performed on river water samples and sand filter effluent samples. Ozone consumption, reduction of UV absorbance and BDOC formation were monitored with applied ozone doses from 0 to 10 mg/L and with contact times from 0 to 60 min. The BDOC formation was optimum at an applied ozone dose of 0.25-0.5 mg O₃ per mg DOC (contact time = 5 min) corresponding to apparition of traces of residual ozone and maximum UV reduction. Maximum ozone consumption, UV reduction and BDOC formation occurred simultaneously during the first two minutes of treatment. Concerning BDOC formation, applied ozone dose showed a greater effectiveness than contact time. For the same quantity of consumed ozone, a short contact time associated with a high ozone dose was preferable to a long contact time and a low ozone dose.     

Kinetic study of the curing behavior of bismaleimide modified with diallylbisphenol A

The curing kinetics of bismaleimide modified with diallylbisphenol A were investigated for different ratios of 1,1′‐(methylene di‐4,1‐phenylene) bismaleimide and diallylbisphenol A with differential scanning calorimetry. Multiheating‐rate and isothermal methods were used to study the kinetics of the curing process. The results indicated that the activation energy changed with the extent of conversion. The activation energy obtained by the multiheating‐rate method was higher than that obtained by the isothermal method. Two kinetic models (autocatalytic and nth‐order) were successfully used to model the curing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2229–2240, 2003     

UV涂料在户外的应用

本文简述了辐射固化技术的发展历史，回顾了我国辐射固化涂料的发展状况，介绍了户外用UV涂料的特点、制备及国外最新进展。     

Potential of microbial growth control in water hydraulic systems by UV‐irradiation and filtration

Water hydraulic systems use water as a pressure medium and, thus, do not pose such adverse environmental impacts as oil hydraulics. Microbial deterioration of the pressure medium and biofouling of the surfaces restrict the applicability of the water‐based technology. The potential of microbial growth control by UV‐irradiation and filtration was studied in a pilot‐scale water hydraulic system. The UV‐irradiation (25 m Ws cm^?2) of the pressure medium reduced the total viable counts of bacteria by 1–2 log₁₀ cfu cm^?3, whereas the total microbial cell numbers and the numbers of surface‐attached microorganisms remained unaffected. Prefiltration (1.2 µm, absolute) of the pressure medium decreased the total microbial cell number in the water phase and retarded the attachment of bacteria. The filtration during the operation (2 µm, absolute) decreased the total numbers of microbial cells and the total viable counts in the pressure medium, and microbial attachment on the surfaces. Microbial attachment was not prevented by filtration. The microbial water quality obtained by pre‐ and on‐line filtration of the pressure medium was sufficient to ensure the long‐term operation of the water hydraulic system assuming that clean work practices are complied with in assembly and during the operation. © 2002 Society of Chemical Industry     

改性蓖麻油制备UV光固化涂料的研究

研究了改性蓖麻油制备UV光固化涂料。由蓖麻油、环氧丙烯酸树脂UVR6100、光引发剂UVI6990制得的涂料具有优良的光泽、良好的柔韧性、良好的附着力与硬度，且当改性蓖麻油含量为40％时，漆膜性能最为优良。     

榫边扣合管状密闭输送带的制作及其质量优化

对用于制药、精细化工、建材业等输送松散及粉、粒物料不污染环境的榫边扣合管状密闭输送带的结构特点、技术要求、制造工艺和优化制品质量的技术措施及效果进行了实验探讨。     

多官能度聚氨酯丙烯酸酯的合成及性能研究

采取两步法合成了高官能度聚氨酯丙烯酸酯,用实时红外光谱研究了多官能度聚氨酯丙烯酸酯的光聚合动力学,并研究了多官能度聚氨酯丙烯酸酯与其它单体配方的机械性能。研究发现随着丙烯酸官能度的增多,双键转化率也随之降低;官能度的增加会提高漆膜的硬度。     

Curing process of powdered phenol–formaldehyde resol resins and the role of water in the curing systems

The curing behavior of two kinds of commercial powdered resol phenolic resins was studied by differential scanning calorimetry. Liquid‐state ¹³C‐NMR spectroscopy was used to aid in understanding the curing behavior by detecting the structure of powdered resins. The reaction mechanism was interpreted with the dependency of activation energy on the degree of conversion. The results indicate that there are differences in the curing mechanism between core and face phenolic resins. The curing process of core resin was faster than that of face resin at the same reaction temperature. The water added in the curing system played an important role of plasticizer or diluent according to different curing stages and water content. In the initial curing stage, water mainly diluted the system and retarded the curing reactions. However, at the higher degrees of conversion, water played the role of plasticizer to decrease the effect of diffusion on the curing reactions to make the curing reactions more complete. The excess water added in the curing system played the role of diluent at almost all stages during the curing process. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1371–1378, 2003