烟气轮机特殊状态下的保护

从烟气轮机超速的极限开始 ,分别按照阀门的关闭时间为 1 .5s和 6s的两种典型状态 ,对烟机在联轴节断裂等特殊工况下的超速情况进行了分析。最后 ,对烟气轮机在特殊工况下的保护提出了建议。     

风扇磨煤机ZGMn13冲击板的失效分析

ZGMn13冲击板的失效方式为不同角度的粒子撞击和冲刷，其表面可以分为三个典型的磨损区域：低角度撞击区、高角度撞击区和冲刷区。详细分析了该三个磨损区域的磨损机理。次表面分析的结果表明，在低负度撞击和冲刷条件下，高锰钢未能充分加工硬化，耐磨性提高有限。     

对编写《水轮机》新教材的建议

提出适应新的中等职业《水轮机》教材和课程教学大纲的修改建议。     

野外大气扩散试验中四面体气球示踪实验的初步评价

1985年11月在瑞士北部进行了一次以探讨“冷池”条件下的扩散和湍流特征为目的的国际野外大气试验,本文介绍其中的四面体气球示踪实验的结果。一共进行了三次由雷达跟踪的四面体示踪实验,释放了10个四面体球。按多轨迹法和单轨迹法分别估算并比较了其中两次示踪实验得到的水平扩散参数σ_y,探讨了风摆效应的贡献。采用“体源模式”并结合单轨迹法估算了微弱风场不定风向条件下的扩散参数,分析了静风,弱风条件下的水平风向标准差和湍流强度。     

论剪切质量的提高

通过对飞剪剪切长度，精度，剪刃间隙和压板机构等参数的优化，来提高钢板的剪切质量。     

Local acceptance of wind energy: Factors of success identified in French and German case studies

The objective of this paper is to identify and analyse factors that are important for winning acceptance of wind-energy parks on the local level. The developers of wind-energy parks need to know how to manage “social acceptance” at the different stages of planning, realisation and operation. Five case studies in France and Germany focused on factors of success in developing a wind-energy project on a given site and illuminated how policy frameworks influence local acceptance. Our hypothesis is that these factors fall into two categories: institutional conditions, such as economic incentives and regulations; and site-specific conditions (territorial factors), such as the local economy, the local geography, local actors, and the actual on-site planning process (project management).     

俄罗斯减速器涡轮钻具驱动PDC钻头在西西伯利亚油田的成功应用

涡轮钻具由前苏联研制出来以后，得到了迅速发展，目前已发展到减速器涡轮钻具阶段。现在，俄罗斯西西伯利亚地区普遍使用减速器涡轮钻具钻井，而减速器涡轮钻具驱动PDC钻头的使用还是空白。采用俄罗斯生产的几种不同型号的减速器涡轮钻具，在西西伯利亚进行了驱动PDC钻头钻井的阶段性试验。试验结果表明，在优选PDC钻头结构的情况下，用减速器涡轮钻具驱动PDC钻头，钻头进尺和机械钻速都较牙轮钻头有显著的提高，经济和社会效益显著。介绍了试验中使用的3种俄罗斯减速器涡轮钻具(TPM-195，TPⅢ-195和TPO3—195)的结构特点和主要技术参数。     

运用现代CFD方法设计高效率的汽轮机(续前期)

论述了运用现代计算流体动力学(ComputationalFluidDynamics,CFD)技术设计高效率汽轮机的方法,典型应用的实例有全三维叶片级流场、叶片汽封和排汽蜗壳计算。计算结果和实际是相符的。进一步对结构性单元和非结构单元程序的计算结果进行了比较,已证明,非结构单元CFD程序用于复杂形状的流场计算时,结果与实际相当一致,并具有独特的功能。     

Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Operating experience from the ehecatl wind turbines

This paper presents a summary of the mechanical features and the medium term operating experience from three small horizontal axis wind energy conversion systems covering a range of 500 to 5000 Watt, intented for rural and isolated communities. These turbines have a new regulator which reduces gyroscopic loads, is easy to adjust and could be manufactured stronger and in smaller sizes than the conventional tail vanes. It is concluded that is feasible to build cheaps and reliable wind turbine generators with an acceptable efficiency employing common-use elements, but is needed a careful and optimized design.