The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

Off-Optimum Cure of Aerospace Epoxy Adhesives

Four epoxy film adhesives used in aircraft manufacture and repair have been examined to establish the effect of deviation from the cure cycle specified by the manufacturer. In addition to the variation of the cure cycle, two surface preparations of the aluminium adherends (chromic acid etch or grit blast followed by silane treatment) were evaluated. Thermal analysis was used to examine the cure envelope of the adhesive, and its extent of cure and glass transition temperature. The adhesive properties were assessed by shear strength (in both single lap joints and in Iosipescu configuration), durability (Boeing wedge test) and chemical resistance to selected aggressive fluids. The sensitivity of the performance of a particular adhesive to offoptimum cure conditions depends on its composition and needs to be determined, not predicted.     

结构粘结剂的试验研究

粘结剂是粘钢加固技术的关键材料,通过对粘结剂的试验研究,得到了粘结剂的拉压试验曲线与材料力学指标以及粘附于各种标号混凝土时,粘结层的抗剪强度;并且还进行了粘结剂的短期流变试验。     

Modeling of Moisture Behavior of Wood Planks in Nonvented Flat Roofs

A computer model was extended and adapted to simulate the hygrothermal behavior of building envelope-wood components. The model was used to predict moisture movement in wood planks forming the decks of nonvented flat roofs insulated with cellulose. The gradient of water potential was considered as the driving force for moisture movement in wood. The model required the determination of convective heat- and mass-transfer coefficients, the sorption curves, the effective water conductivity for different wood species, and the hygrothermal conditions within the assembly to characterize the mass-conservation equation. Once these parameters were integrated in the computer model, this approach was then validated by carrying a simulation of the drying process of wood planks using experimental data from a large-scale test.     

A Mass Transport Model for Drying Wood under Isothermal Conditions

Mass transport in wood during drying can have different mechanisms at different periods of drying. Depending on the current moisture content (MC) and the structure of the wood, the driving forces for the mass transport are essentially different. Above the fiber saturation point (FSP), the lumens are partially saturated and the transport of liquid (free) water occurs as a consequence of capillary action. On the other hand, below the FSP, bound water within the cell walls is conveyed by diffusion, and water vapor in the lumens moves under influence of pressures gradient. Based on these considerations, a unified model is presented that takes into account the transport of the different moisture phases. Simulation of the drying of a Norway spruce sample at 50°C from about 135 to 7% MC is carried out using the finite element method (FEM). Comparison between the simulated average MC and the experimental observations obtained from X-ray computed tomography (CT) shows reasonable agreement. Possible simplifications in the model are briefly discussed as well as some aspects of the numerical implementation. Finally, the influence of absolute permeability on the average MC is studied.     

Energy Saving in Industrial Wood Drying Addressed by a Multiscale Computational Model: Board, Stack, and Kiln

This article proposes a multiscale computational model able to calculate energy consumption in a batch lumber kiln. A dual-scale computational model of wood drying deals with the boards/stack interaction and serves as a basis for the present work. A new module was added here that calculates heat losses through kiln walls (convection, condensation) and the energy used by each kiln component (fans, heating elements, humidifier, vacuum pump, etc.). The corresponding mathematical formulation is presented and then theoretical results are compared to those collected in an industrial vacuum kiln. As application example, the effect of air reversal, air velocity, and kiln insulation are exhibited, which depicts the great potential and prospects of this new tool for energy savings in relation to the product quality.     

Water‐soluble/dispersible cationic pressure‐sensitive adhesives. I. Adhesives from solution polymerization

Pressure‐sensitive adhesives (PSAs) have long been a problem as sticky contaminants for paper recycling mills. The main problem associated with such stickies is that the PSAs in the waste papers deposit on the felts, press rolls, and drying cylinders of paper machines, and this creates problems with paper formation, reducing the paper quality and paper machine runnability. The annual cost of stickies to the U.S. paper industry is estimated to be about $600,000,000–650,000,000. To solve this problem, a series of cationic water‐soluble/dispersible PSAs have been synthesized by the free‐radical solution polymerization of butyl acrylate and [3‐(methacryloylamino)propyl]trimethylammonium chloride in ethanol. The PSA end‐use properties, repulpability in paper recycling, and the effects on the properties of recycled paper products have been studied. The cationic PSAs can be dissolved or dispersed in water if the cationic charge density in the PSA backbone is controlled, and so they do not deposit as stickies during recycling and papermaking processes. Because the PSAs are cationically charged, they can easily be removed from the papermaking system by adsorption onto the negatively charged fibers and fine surfaces. Furthermore, the adsorbed colloidal or dissolved PSAs have little effect on the final paper properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1624–1630, 2003     

Viscoelastic Windows of Pressure-Sensitive Adhesives

A viscoelastic window (VW) concept has been proposed to identify different types of pressure-sensitive adhesives (PSA's). Such viscoelastic windows are constructed from the values of dynamic storage modulus: G' and dynamic loss modulus G' at frequencies of 10^-2 and 10² rad/sec. These frequencies are chosen because the range covers most of the time scales corresponding to the uses of PSA's at different application rates in performance tests. A four quadrant concept has also been recommended to categorize different types of PSA's based on the location of their VW's on the log-log cross plot of G' and G'. It was found that for most PSA's, the range of G' and G' at room temperature within these selected frequencies falls between 10³ and 10⁶ Pascals. The proposed four-quadrants (top-left hand quadrant of high G' and low G', top-right hand quadrant of high G' and high G', lower left hand quadrant of low G' and low G', and lower right-hand quadrant of low G' and high G') correspond respectively to (1) non-PSA or release coatings (2) high shear PSA's, (3) removable PSA's and medical PSA's and (4) quick and cold stick PSA's. It was also observed that the VW's of general purpose permanent PSA's occupy the central region which straddles part of the four quadrants.     

Adhesive Dispensing Process Analysis: Steady-State Dispensing of One-Component Adhesives

The process of dispensing one-component heat-cure adhesives was investigated in order to understand current application processes and to guide new process development. Typical one-component adhesives exhibit non-Newtonian rheological behavior, and hence Newtonian fluid mechanics does not adequately describe the dispensing process. In the present study, the adhesives were modeled as Bingham fluids possessing a yield stress and a steady state viscosity. The model of the dispensing apparatus includes four major flow sections connected in a serial configuration. The fluid mechanics equations derived for Bingham fluids in the individual flow sections were solved by numerical methods in order to understand the interrelationships between the material variables (e.g. yield stress, viscosity, temperature dependencies) and process variables (e.g. pressure, flow geometry, temperature, output). The concept of the model is generic and the details of the model can be modified for any forced-flow adhesive application process.

The adhesive flow properties significantly influence the process output. Dispensing temperature, among the process variables, has the strongest effect on process output. A ± 1.0·C perturbation in the dispensing temperature can cause as much as a 14% variation in the bead size for the range of adhesives studied. Differences in flow characteristics result in differences in processability and non-linear temperature/pressure sensitivity. The non-linear sensitivity can be eliminated by operating the dispensing process isothermally. Finally, the process limits for one-component adhesives, which are susceptible to chemical instability induced by viscous heating during processing, are defined and discussed in terms of a modified Brinkman number that takes into account viscous dissipation, heat conduction and convection, and chemical stability of the material during processing.     

美国对邮票用压敏胶的开发

介绍了美国对邮票用压教胶的开发情况及其在废纸回用过程中的良好表现，