板式换热器热端跑冷问题的分析及处理

１００００ｍ３／ｈ制氧机板式换热器损坏修复后，热端跑冷严重，氧气取出量不足，制氧机工况恶化，通过分析找出了原因是因某单元氧通道堵塞，并采取了处理措施。     

一种蒸发式冷凝器的新型设计方法

蒸发式冷凝器设计方法的粗糙和繁琐限制其广泛应用,特别是限制其应用于民用和小型商用建筑中。针对上述问题,作者通过实验研究了蒸发式冷凝器的影响因素（进风湿球温度、最小截面风速和喷淋水量）对蒸发式冷凝器热质交换的影响。同时提出了一种新型设计方法,此方法简单,精度较高。适合工程设计、选型和生产应用。     

合理选用过剩空气系数的重要性分析

通过分析过剩空气系数过大或过小时加热炉多方面的影响,强调了合理选用过剩空气系数的重要性,并提出了控制措施。     

珠海拱北口岸联检大楼空调设计

介绍了珠海拱北口岸联检楼空调系统的设计特点，提出了按建筑类型、功能进行空调系统分区的设计方法，强调应根据建筑物的具体情况设置设备用房，以保障空调系统正常有效地运行。     

简述空调环境微生物传播及防治

简要论述了一般空调环境下的主要微生物种类及其主要传播方式，分析了影响其传播的因素，同时介绍了现在常用的防治方法，提出了一些改进的意见。     

Hard disc drive air bearing design: modified DIRECT algorithm and its application to slider air bearing surface optimization

Hard disk drives continue to increase in areal data density. This requires air bearing sliders with lower and lower flying heights (FH). Also the uniformity of the FH and the flatness of the roll profile with radius become more critical as the FH gets lower. By using modern optimization techniques, it is possible to optimize slider air bearing surface (ABS) designs according to multiple design goals. In this paper, we discuss two modifications to the DIRECT algorithm: one to handle tolerance and one to deal with hidden constraints. Some numerical experiments were carried out using these modifications and the modified DIRECT algorithm was applied to slider ABS optimization. The results show that these two modifications can improve the efficiency of the DIRECT algorithm and they also provide more flexibility in slider ABS optimization.     

蒸发式冷凝在制冷工艺上的应用

分析对比制冷工艺中几种冷凝方式，指出发展蒸发式冷凝技术对制冷系统节能的重要意义；通过分析蒸发式冷凝的换热机理，在试验和实践的基础上讨论了影响蒸发式冷凝器性能的几个重要因素。     

等离子喷涂燃料电池连接板LSM薄膜的性能研究

采用等离子喷涂法在SUS 430连接板基体上制备了LSM(La0.8 Sr0.2 MnO3)薄膜。用X射线衍射仪、扫描电镜和电子探针分别研究了喷涂前后LSM的相组成、薄膜的表面形貌和元素分布。用图像分析法计算了薄膜的孔隙率。二支点法测量了有与无LSM薄膜的SUS 430基体在130～800℃时的电导率。结果发现,薄膜与基体结合良好,薄膜孔隙细小,均匀分布,且非连通;LSM的相组成在喷涂前后保持一致;当温度<330℃时,有LSM保护膜的连接板的电导率小于无LSM薄膜的连接板的电导率;温度>330℃,结果相反。有LSM保护膜的连接板在空气中,130～800℃下,最大电导率为0.60Ω-1·cm-1。     

Fabrication and properties of PLZT ceramics from spray-dried aqueous solution

PLZT ceramics with the composition of 9/62/38 (La/Zr/Ti) were fabricated from spraydried aqueous solution. Complete crystallization of the spray-dried powder is achieved after 1 hr calcination at 650‡ C as compared to 800‡ C, 1 hr for conventional mixedoxide method. Sintering environment plays an important role in the densification of PLZT ceramics. Densities of the atmosphere sintered samples are much higher than those of normal sintered ones. PLZT ceramics derived from spray-dried powders have properties comparable to those derived from sol-gel ones. The spray-dried method presents a less expensive and more effective approach in the synthesis of PLZT ceramics.     

Catalytic wet air oxidation of butyric acid solutions using carbon-supported iridium catalysts

Aqueous solutions of butyric acid were treated by catalytic wet air oxidation using carbon-supported iridium catalysts in a stirred reactor. Under the operating conditions of 6.9 bar of oxygen partial pressure and 200 °C of temperature, conversions up to 52.9% after 2 h were obtained depending on the type of catalyst used. The effects of butyric acid initial concentration, loading of catalyst, oxygen partial pressure and temperature were investigated and the empirical rate law for acid conversion is presented. Oxidation intermediates such as propionic and acetic acid were identified. The heterogeneous catalyzed free-radical oxidation of butyric acid is discussed.