高功率激光系统通过空间滤波和中继成像抑制自聚焦

讨论了由光束自聚焦引起的细丝形成和光束分裂，为了克服聚焦造成的破坏要求在光束传播中采用中继成像和空间滤波。     

码分多址（CDMA）技术和公用空中接口综述

本文主要讨论数字移动通信中扩频码分多址技术，阐明了ＣＤＭＡ体制的优越之外，分析了ＣＤＭＡ的关键技术，全面介绍了ＣＤＭＡ系统设计的基本原则和ＩＳ－９５－Ａ空中接口标准的含义。     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.     

用发生炉煤气进行快速热风烤窑的应用

用发生炉煤气进行快速热风烤窑的应用王善波，王志军（山东荣成市玻搪工程有限公司２６４３０９）ＰｒｏｄｕｃｅｒＧａｓＵｓｅｄｆｏｒＦａｓｔＨｅａｔｉｎｇｕｐＴａｎｋＦｕｒｎａｃｅ￥ＷａｎｇＳｈａｎｂｏ；ＷａｎｇＺｈｉｊｕｎ（ＳｈａｎｄｏｎｇＲｏｎｇｃｈｅ...     

大泵站超驼峰水位运行压缩空气断流系统的设计方法

阐述了压缩空气断流的原理，提出了压缩空气断流装置的一般构成和设计方法，首次应用气体喷射器作为压缩空气减压增量变换器，不但及时地增加了补气量，防止断流后流道压力的下降，而且大大减小了储气罐容积，使该项技术得以满足工程实际的要求，为同类泵站的技术改造     

武钢 3×10~4m~3/h 空分手动变负荷生产的探索与实践

对武钢引进的两台３×１０４ｍ３／ｈ空分设备，为改变其自动变负荷生产调节范围小、时间长的问题，采用了人工手动变负荷的操作方法。实践表明：扩大了增减产范围，缩短了调节时间，有十分明显的综合经济效益，可供大型空分变负荷生产借鉴参考。     

4TYD112型离心空压机联轴器故障的分析及处理

对新冶钢动力厂制氧机组配套的原料空气压缩机故障现象进行了原因分析,并有针对性地提出了处理措施,经运行检验,故障基本消除。     

挑坎型掺气减蚀设施过流掺气特性研究

采用一维激光测速系统，对掺气减蚀工程中常用的直线型挑坎的流场特性进行试验研究．通过测量挑坎上及空腔区水流的流速分布及紊动特性，探讨通气量与紊动强度的关系．同时在深入研究流场特性和掺气机理的基础上，通过分析影响掺气的因素，从理论上探求临界掺气流速的计算，重点分析挑坎型掺气过流在空腔负压较大的情况下，临界掺气条件的理论预测，并通过试验资料验证了该计算方法．在此基础上，还进一步研究了掺气量的计算公式及其变化规律．     

气囊内模制作桥面板在华丰湾防洪工程中的应用

采用气囊作内模进行浇筑桥面板混凝土 ,加快了预制桥面板施工进度 ,确保工程施工质量 ,并降低了工程施工成本     

高浓度钢渣粉尘环境发动机空气过滤系统的改进与维护

针对液压挖掘机在高浓度钢渣粉尘作业环境下,钢渣粉尘对发动机的损害,分析了发动机空气滤清器的作用,阐述了传统空气过滤系统存在的问题,提出了改进的方案与维护措施.