Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

Measurement of the Metal Surface Acidity/Electronegativity of Pt(110)

In previous work, it has been found that a hydrogen-covered Pt(110) surface is acidic, but quantification of the acidity has not yet been done. In this paper a spectroscopic method is developed to measure the acidity of a metal surface for the first time. The technique involves measuring the intensity of the N–H stretch from the C₅H₄XNH⁺ that forms when hydrogen coadsorbs with pyridine, 2-fluoropyridine and 3-fluoropyridine. The Bethe approximation is then used to estimate the metal surface acidity/electronegativity (MSAEL). The proton affinity/MSAEL of Pt(110) has been determined to be 907 ± 4 kJ/mol at high coverage. This is the first time the MSAEL has been measured on a metal surface. Implications for fuel cell catalysis are discussed.     

纤维素的辐射裂解及其化学性质

纤维素经高能射线辐照,能产生一系列的化学和物理性质的变化。本文报道在不同剂量的~(60)Coγ射线辐照下,稻草中的水溶性糖、易水解糖、难水解糖,以及氨基酸、蛋白质等物质的化学变化;用辐射与加泡涨剂相结合的方法处理稻草,可以降低剂量、提高效应。     

锌基合金模具的应用及探讨

本文分析了锌基合金模具制造及使用过程中容易出现热裂、翘曲、收缩的问题，并提出了解决这些问题的措施。     

Metal sorption by biomass of melanin‐producing fungi grown in clay‐containing medium

The sorption of toxic metals by fungal mycelia grown in clay‐containing medium is reported in this work. Biomass of melanin‐producing microfungi of the genus Cladosporium (C cladosporioides, C resinae and C herbarum) and Aureobasidium pullulans, clay minerals and fungal mycelia grown in clay‐containing medium were compared for their equilibrium Cu and Cd uptake from pH‐buffered solutions using experimental sorption isotherms. Bentonite (Cherkassy) in the natural form was shown to be the best Cu sorbent compared with the other clays and clay minerals tested. Cu sorption isotherms fitted the Langmuir sorption model for all cases. Comparison of Cu and Cd uptake for biomass and bentonite showed a lower biomass uptake capacity but a considerably higher affinity of the biosorbent for the solute. The presence of kaolinite and palygorskite in the medium generally reduced both Cu and Cd sorption capacity and the metal‐binding ability of the fungal–clay mixtures. In contrast, addition of bentonite into the medium did not appreciably alter the Cd sorption ability but increased the sorption of Cu by A pullulans and C cladosporioides grown in this medium. A common feature for all fungi grown in the presence of bentonite was an increase in the Cu sorption capacity (Q_max) of the biomineral sorbents and a reduction in their affinity (Langmuir parameter b) compared with control biomass. A difference between predicted and experimental data obtained for biomass grown on bentonite medium was also observed. The connection between the sorption capacity of biomass grown in clay‐containing medium, mycelial morphology and the structure of fungal pellets is discussed and a mechanism for the changed sorption capacity of the combined biomineral sorbents is proposed which involves blocking or modification of binding sites on biotic and abiotic components of the ‘biomineral’ association. © 2002 Society of Chemical Industry     

浅谈水闸安全检测

通过对华东沿海地区80年代以前修建的一些在役水闸工程的系统安全检测和分析,发现了水闸工程存在的安全隐患,同时也了解水闸工程尚有的潜在能力。提醒水闸管理部门,在役水闸满足目前社会发展需要的同时,还必须高度重视水闸的安全生产运行和管理。水闸安全检测就是利用先进的检测手段,为业主及时、高效、经济和高质量地解决水闸工程存在的实际问题。     

Influence of the Temperature of a Body on Its Weight

The physical preconditions are considered for the temperature of a body to influence the force of gravity experienced by it. The results are given of experiments on weighing metal rods heated by ultrasound which confirm a dependence of the weight of the rods on their temperature.     

Hydrogen Absorption and Release Behavior in Hydrogen Decrepitation Process of Nd-Fe-B Alloys

The behavior of hydrogen absorption and release in hydrogen decrepitation (HD) process of Nd-Fe-B alloys were investigated. The results reveal that the reactivity and the amount of hydrogen absorption in HD process are related to the surface activity of the alloy so that the fresh and active surface has a higher efficiency. The presence of Nd-rich phase at the grain boundary is an essential factor of the HD activity of the alloy at room temperature. On degassing, hydrogen is released from the HD powder continuously with increasing temperature. And the residual hydrogen is as low as 0.0015% at 1073K, which shows that the hydrogen is almost exhaused. It is feasible to remove the hydrogen from the HD powder by heating treatment at the temperature of 523-723K for 1h prior to the magnetic field forming in order to decrease the harmful effect of hydrogen on the easy axis alignment of HD magnet.