Improved synergetic excitation control for transient stability enhancement and voltage regulation of power systems

This paper proposes decentralized improved synergetic excitation controllers (ISEC) for synchronous generators to enhance transient stability and obtain satisfactory voltage regulation performance of power systems. Each generator is considered as a subsystem, for which an ISEC is designed. According to the control objectives, a manifold, which is a linear combination of the deviation of generator terminal voltage, rotor speed and active power, is chosen for the design of ISEC. Compared with the conventional synergetic excitation controller (CSEC), a parameter adaptation scheme is proposed for updating the controller parameter online in order to improve the transient stability and voltage regulation performance simultaneously under various operating conditions. Case studies are undertaken on a single-machine infinite-bus power system and a two-area four-machine power system, respectively. Simulation results show the ISEC can provide better damping and voltage regulation performance, compared with the CSEC without parameter adaptation scheme and the conventional power system stabilizer.     

microRNA在亨廷顿病中的研究进展

亨廷顿病(Huntington's disease, HD)是神经退行性疾病(neurodegenerative disorders)中一种单基因遗传病,由亨廷顿基因(the huntingtin gene, HTT)第一个外显子中的CAG三核苷酸序列重复扩增引起,尚无法治愈。HTT编码的蛋白产物被称为亨廷顿蛋白(Huntingtin protein, Htt)。突变亨廷顿蛋白(mutated huntingtin protein, mHtt)容易形成聚集体,具有毒性,导致一系列细胞学异常和神经元功能障碍。microRNA(miRNA)在基因转录后水平调控中起重要作用,其表达的改变与HD病理过程有关,成为治疗HD的潜在生物标志物。近年来,对一些特定miRNA在HD中调控机制及靶基因预测方面的研究可为HD提供潜在的治疗方法。本文就miRNA在HD中的相关研究进展进行综述。     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

Super-oleophilicity Co-doping Co2+/F-/TiO2 one-dimensional nanotubes for photocatalytic denitrification of light oil

In this study, a simple hydrothermal synthesis method was adapted for the preparation of Co-doping Co²⁺/F^-/TiO₂ nanotubes photocatalyst, and the micro-nano structure of catalysts prepared by biomimetic technology which makes the catalyst have super-oleophilicity property. Co²⁺/F^-/TiO₂ revealed improved photocatalytic performance for denitrification of light oil compared to single TiO₂ photocatalysts. The enhance of photocatalytic activity can be attributed to narrowing the band gap, increasing the light response wavelength and exposing more highly active crystal surfaces due to synergistic effects of Co²⁺ and F^? in the photocatalyst.     

Artificial bee colony based algorithm for maximum power point tracking (MPPT) for PV systems operating under partial shaded conditions

Artificial bee colony (ABC) algorithm has several characteristics that make it more attractive than other bio-inspired methods. Particularly, it is simple, it uses fewer control parameters and its convergence is independent of the initial conditions. In this paper, a novel artificial bee colony based maximum power point tracking algorithm (MPPT) is proposed. The developed algorithm, does not allow only overcoming the common drawback of the conventional MPPT methods, but it gives a simple and a robust MPPT scheme. A co-simulation methodology, combining Matlab/Simulink™ and Cadence/Pspice™, is used to verify the effectiveness of the proposed method and compare its performance, under dynamic weather conditions, with that of the Particle Swarm Optimization (PSO) based MPPT algorithm. Moreover, a laboratory setup has been realized and used to experimentally validate the proposed ABC-based MPPT algorithm. Simulation and experimental results have shown the satisfactory performance of the proposed approach.     

Catalytic Hydrocracking of a Bitumen‐Derived Asphaltene over NiMo/γ‐Al2O3 at Various Temperatures

Hydrocracking of a bitumen‐derived asphaltene over NiMo/γ‐Al₂O₃ was investigated in a microbatch reactor at varying temperatures. The molar kinetics of asphaltene cracking reaction was examined by fitting the experimental data. Below a defined temperature, the molar reaction showed the first‐order kinetic feature while at higher temperatures secondary reactions such as coke formation became significant, causing deviation of the reaction behavior from the proposed first‐order kinetic model. Selectivity analysis proved that dominant products varied from gases to liquids to gases with increasing temperature, shifting the dominant reaction from C–S bonds cleavage to C–C bonds cleavage.     

Low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy

The eutectic 80Au/20Sn solder alloy is widely used in high power electronics and optoelectronics packaging. In this study, low cycle fatigue behavior of a eutectic 80Au/20Sn solder alloy is reported. The 80Au/20Sn solder shows a quasi-static fracture characteristic at high strain rates, and then gradually transforms from a transgranular fracture (dominated by fatigue damage) to intergranular fracture (dominated by creep damage) at low strain rates with increasing temperature. Coffin-Manson and Morrow models are proposed to evaluate the low cycle fatigue behavior of the 80Au/20Sn solder. Besides, the 80Au/20Sn solder has enhanced fatigue resistance compared to the 63Sn/37Pb solder.