基于电源、地桥的电源网络布线后优化

随着集成电路规模的不断增大,电源网络的重要性日趋显著,电源网络的分布直接影响芯片的电压降(IR-drop)。一种布线后通过在空闲处插入电源桥和地桥的方法,可以在不增加芯片面积的情况下,改善IR-drop效应。实验结果表明在芯片布局利用率不高的情况下(70~75%),该方法可以使IR-drop得到明显的优化。     

提取地震信号高频信息方法的若干问题

岩性油气藏勘探已成为当代油气勘探的重要组成部分,因此提取地震资料高频信息已成为一个重要研究课题。文中对分辨率、分频处理地震信号、波阻抗反演中的一些问题进行了较深入的讨论,并得出以下认识:1要提高垂向和横向分辨率,必须设法提高野外采集地震资料的频率;2地震分频处理是偏移后提高分辨率的常用方法之一,这种方法应该限定在地震波的有效频带内,而超出有效频带,可能会带来很多假像;3低频合成地震记录中高频反射系数存在不确定性。在基于模型波阻抗反演的方法中,反演结果受初始模型的影响非常大,初始模型是依据测井资料建立的,初始模型与实际情况越接近,反演效果就越好;否则,会产生模型化的现象;4在相对波阻抗数据体(相当于地震数据体)作为约束条件下的SP测井参数协克里金插值是正演过程,消除了模型化的问题,使反演结果更接近真实情况,提高了砂层真实的分辨率。     

双电池系统电源选择器MAX1773/1773A

MAX1773／MAX1773A是用于双电池系统的电源选择器，它允许外部控制器去管理双电池组、适配器输入、电池充电器和系统负载所需的电源连接。文中介绍了MAX1773／1773A的特点、引脚功能、内部结构和工作原理，给出了MAX1773/MAX1773A的典型工作电路。     

Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

GPRS手机入网测试自动化

全球移动通信系统(GSM)广泛的应用于现代通信系统就在于其良好的兼容性,不同的移动设备之间在遵守一定协议规范的条件下可以相互通信;本设计测试的是GSM第11系列GSM11.10,他包括诸多测试项,只对接收机参考灵敏度电平在GSM900与DCS1800两个频段进行测量。给出了传统形式下的手动测试和自动测试平台的比较,并建立了收信机参考灵敏度指标的自动测试平台。     

DS/FH通信系统的跳频同步技术研究

同步是DS/FH混合通信系统的关键技术之一。根据跳频系统中对同步的要求,介绍了一种适用于DS/FH混合扩频通信系统的跳频同步方法,采用同步字头和精准时间相结合的方法实现跳频同步。对同步性能进行了分析,结果表明该跳频同步方法同步时间短,捕获概率高。     

Finite element piezothermoelasticity analysis and the active control of FGM plates with integrated piezoelectric sensors and actuators

 An efficient finite element model is presented for the static and dynamic piezothermoelastic analysis and control of FGM plates under temperature gradient environments using integrated piezoelectric sensor/actuator layers. The properties of an FGM plate are functionally graded in the thickness direction according to a volume fraction power law distribution. A constant displacement-cum-velocity feedback control algorithm that couples the direct and inverse piezoelectric effects is applied to provide active feedback control of the integrated FGM plate in a closed loop system. Numerical results for the static and dynamic control are presented for the FGM plate, which consists of zirconia and aluminum. The effects of the constituent volume fractions and the influence of feedback control gain on the static and dynamic responses of the FGM plates are examined. Received: 13 March 2002 / Accepted: 5 March 2003 The work described in this paper was supported by a grant awarded by the Research Grants Council of the Hong Kong Special Administrative Region, China (Project No. CityU 1024/01E).     

镍层耐硝酸腐蚀性测试——一种简单的预先探测ENIG镍层“黑盘”现象的测试方法

随着更加精细的SMT、BGA等表面贴装技术的运用,化学沉镍金(ENIG)作为线路板最终表面处理得到了越来越广泛的应用,同时可怕的“黑盘”现象也随之更广泛地“流行”起来,直接导致贴装后元器件焊接点不规则接触不良。为了贯彻执行最好的流程控制和采取有效的预防措施,了解这种焊接失败的产生机理是非常重要的,及早的观测到可能发生“黑盘”现象的迹象变得同样关键。本文介绍了一种简单的预先探测ENIG镍层“黑盘”现象的测试方法-镍层耐硝酸腐蚀性测试,这种测试可以用于作为一种常规的测试方法监测一般化学沉镍溶液在有效使用寿命范围内新鲜沉积的镍层的质量。利用Weibull概率统计分析在不同的金属置换周期(MTO)下镍层的可靠性能表现。结合试验结果得出了一个镍层耐硝酸腐蚀性的判定标准。     

单光纤传输光推动便携式压力测量仪的研究

介绍了用单根光纤传输测量信号和功率信号的光功率推动液体压力测量仪及其工作原理。该仪器以电容式压力传感器的δ元件作为压力检测元件，采用低功耗前置器电路和简单直杆结构，实现了便携式测量。测量范围为O～100kPa，精度为O．01kPa。     

Fe3O4/PSt/TiO2多层包覆电磁响应微球的制备

首先采用分散聚合法将自制的Fe3O4磁流体和苯乙烯反应合成有磁核的Fe3O4/PSt磁性聚合物微球，然后，用非均匀成核水解反应在Fe3O4/PSt微球外包覆无定形二氧化钛，获得Fe3O4/PSt/TiO2复合微粒。用红外光谱、扫描电镜和热分析对粒子的形貌和结构进行了表征。并测试了微粒的介电性能和磁性，结果表明，所制得复合微粒有良好的电、磁响应性。