Failure of a stationary pump engine piston

Piston failures are not a common occurrence, but they do occur, and failure is usually associated with fatigue crack growth. Most failures initiate at the gudgeon pin hole or in the skirt of the piston. Occasionally they fail elsewhere. In the example covered in this paper, failure initiated in the crown and progressed down to the gudgeon pin before final failure occurred. This paper outlines the cause and mode of failure and shows that small metallurgical discontinuities can contribute to these failures under the right circumstances.     

铝型材推弯工艺

通过铝型材圆环的推弯实验,研究了推弯工艺原理、变形过程,结合有限元模拟得到了和实验结果相吻合的型材厚度分布、成形零件卸载回弹后的曲率半径及型材截面畸变.结果表明:推弯零件曲率及截面畸变一致性高,成形模具结构简单且便于调整,数值模拟可以用于推弯工艺的优化分析.     

Structure of rapidly solidified aluminum alloys

This paper is a summary of an extensive research program carried out by the authors on the structure of rapidly solidified aluminum alloys; and a comparison with the work of others also involved in this field. The paper discusses the changes in the dendritic and non-dendritic structure of the matrix at cooling rates from 10^–3 to 10¹⁰ K/s and discusses the hetergeneity of the structure caused by interdendritic-segretion during solidification.     

Preparation of Ultra—fine Aluminum Nitride in Thermal Plasma

Ultra-fine aluminum nitride has been synthesized by the evaporation of aluminum powder at atmospheric-pressure nitrogen plasma in a hot-wall reactor.The average size of aluminum nitride particle is 0.11μm measured by scanning electric mirror(SEM),and the purity is at least over90% evaluated by X-Ray diffraction(XRD).The conversion of Al powder to aluminum nitride is strongly depended on the injection of NH3.Typical experimental parameters such as the feed rate of raw material,the flow rate of ammonia and the position of injecting aluminum powder into the reactor are given.     

P／MCs新型复合材料制备、结构及阻尼性能

采用特殊的渗流法所制备的新型Ｐ／ＭＣｓ复合材料，由高分子聚合物与蜂窝状铝架组成，它具有优异的阻尼性能，并简述了结构对阻尼的影响     

稀土Si_3N_4陶瓷材料中铝的络合滴定法测定

提出了强碱介质沉淀钇及有关杂质元素而与铝进行分离的方法。试液酸化后采用ＮａＦ析出法络合滴定测定铝。     

电动机笼形转子铸铝常见质量问题分析

在电机制造中，笼形转子三相异步电动机的转子铸铝质量的好坏直接影响电机的性能及力能指标。因此本文对常见的转子铸铝质量问题进行了分析，并提出了相应地解决措施，以获得优质的电机。     

泡沫铝的动态压缩性能和吸能性研究

通过测量泡沫铝在动态和准静态压缩条件下的应力 -应变曲线 ,研究了泡沫铝的准静态和动态压缩行为以及不同应变条件下的吸能性 ,并对其应变率效应进行了分析。结果表明 ,在高应变速率和准静态压缩下 ,泡沫铝的σ -ε曲线均表现出弹性变形段、平缓段和密实段三阶段特征 ;泡沫铝的压缩性能具有明显的应变速率敏感性 ,随应变速率的提高 ,流动应力上升 ,吸能性升高     

镁合金表面喷铝防腐蚀层的微观组织分析

在AZ91D镁合金表面热喷铝，用以提高其表面的耐腐蚀性能。采用SEM，EPMA等方法对AZ91D表面喷铝扩散层的组织进行了仔细的观察与分析，发现在防腐蚀层上有大量的Mg17Al12相存在，且呈决状及非连续片状分布。经显微硬度测定，喷铝层硬度较镁合金基体高；腐蚀后这种相凸出于基体，比镁合金基体有较好的耐腐蚀性能。     

表面引发剂对熔融铝合金直接氧化生长的影响

为了控制熔融铝合金直接氧化法制备Al2O3/Al复合材料的氧化生长,采用ZnO,SiO2和MgO3种表面引发剂,研究它们对Al-Si-Zn合金氧化生长过程及Al2O3/Al复合材料组织形貌的影响.结果表明:与未使用引发剂时相比,使用SiO2,ZnO或MgO表面引发剂制备的粉末都能显著地缩短Al-Si-Zn合金的氧化生长孕育期,提高合金氧化生长速率,改善复合材料的胞状生长方式,提高复合材料的组织均匀度和致密度,为实际生产应用提供了依据.实验发现:ZnO表面引发剂的使用效果最为突出,其最佳添加量为12mg/cm2.