氨法处理硫酸装置尾气生产亚铵的实践

介绍用氨法处理硫酸装置尾气生产亚硫酸铵的工艺流程、控制指标、主要设备和生产运行情况。实践表明,氨法SO2吸收率高,可实现装置尾气达标排放,但也存在产品品位较低的问题。对问题进行了分析并提出改进意见。     

Adhesion Mechanisms of Polyurethanes to Glass Surfaces I. Structure-Property Relationships in Polyurethanes and Their Effects on Adhesion to Glass

Polyurethanes were prepared from toluene diisocyanate (TDI), 1-4-butane diol (BDO) and polycaprolactone-based triols with varying molecular weights. Among each molecular weight triol-based urethane, hard segment content was varied from 20% to 70%. Differential scanning calorimetry, tensile testing, and Iosipescu shear testing were done on all the various urethanes prepared. Thermal characterization data revealed the dependence of phase separation on hard segment content as well as on the triol molecular weight. Tensile data and Iosipescu shear data further confirmed the observations made from the DSC data. The data further indicated that phase separation can greatly improve the modulus of cross-linked segmented urethanes. Adhesion of these urethanes to glass surface was evaluated using soda-lime float glass plate. Urethane samples were cast on the air side of the glass plates and adhesion was measured in shear mode. Adhesion data indicated that in addition to hard segment content, modulus, cross-link density, and molecular weight of the triols, phase separation seems to be a major factor in controlling adhesion. Surfaces of the failed adhesion samples were also analyzed and the failure mode was found to be cohesive, in varying degree, with the different urethane systems.     

High solids content emulsions. III. Synthesis of concentrated latices by classic emulsion polymerization

Two different methods of producing bi‐ and trimodal latices of a mixture of methyl methacrylate, butyl acrylate, and small amounts of acrylic acid were tested. It is shown that a combination of concentrating blends of seed particles by semibatch reaction, followed by a nucleation of small particles plus a second semibatch phase allowed us to obtain stable latices with solids contents over 65% and viscosities of below 2500 mPa s^?1 with little coagulum formation. The key parameter in determining latex stability, coagulum formation, and viscosity appears to be the the particle size distribution, and especially its modification attributed to secondary nucleation. Because it is not possible to eliminate water‐soluble monomers from the polymerization recipe, secondary (homogeneous) nucleation must be minimized by careful addition of the free‐radical initiator and choice of monomer feed flow rates. The nucleation of the third population in the trimodal latices is best accomplished with a mixed surfactant system because renucleation by anionic surfactant alone leads to detrimental changes in the particle size distribution (PSD) resulting from excessive flocculation of particles. In addition, it was found that the viscosity of the final products was not sensitive to small changes in the ionic strength of the latex, although neutralization to a pH of 6 effectively doubles the final latex viscosity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1916–1934, 2002; DOI 10.1002/app.10513     

波纹管在氨、甲醇冷凝器中的应用

从换热和力学方面分析了以波纹管为换热元件的管壳式冷凝器在氨、甲醇冷凝器中的应用特点，总结了使用效果；对波纹管在氨、甲醇冷凝器中使用的可靠性进行了论证。     

超声提取-高效液相色谱法测定烟草中烟碱含量

确定了制备烟碱分析样品的超声波提取条件:0.4% NaOH溶液为溶剂,液固比40:1(mL·g-1),提取时间4 h.确定了高效液相色谱法检测烟碱含量的条件为Kromasil C18色谱柱(250 mm×4.6 mm,5 μm),检测波长259 nm,检测温度35 ℃,流动相CH3OH/0.02 mol·L-1磷酸盐缓冲溶液(V/V)为60/40,流速1.0 mL·min-1,进样量10 μL.平均加样回收率98.8%,相对标准偏差1.2%.结果表明超声提取-高效液相色谱法是一种准确度高,速度快的测定烟草中烟碱含量的检测方法.     

商榷用水煤浆代替轻油改造年产30万吨合成氨

介绍用水煤浆代替轻油原料，改造年产３０万吨合成氨装置，重点论述其制氨工艺单元的合理组合和国产化措施。     

氮在钌单晶表面Ru(0001)上的吸附

钌系氨合成催化剂作为第二代氨合成催化剂,近年来日益受到重视。研究氮分子在钌表面上的离解吸附对提高钌催化剂的催化性能有着十分重要的意义。综述了氮分子在Ru(0001)单晶表面吸附的研究进展，并指出钌催化剂的发展方向。     

大化肥煤代油CO耐硫变换工艺流程的设计

分析石脑油制氨装置改扩建为水煤浆制氨装置ＣＯ耐硫变换工艺的特点，具体阐述其工艺流程优化设计中需考虑的主要技术问题。     

分光光度法测定锌铁合金镀层及镀液中的铁

采用分光光度法，以磺基水杨酸为显色剂、双氧水为氧化剂，锌铁合金镀层用稀盐酸溶解，控制pH值为1.5～3，在等吸收点处测定吸光度，并根据比耳定律计算镀层及镀液中的铁含量。     

发挥贵州煤资源优势,加快煤化工的发展

对贵州煤化工现状进行的描述，指出从煤气化路线出发，以煤制合成气制得氮和甲醇为重点，建立大型煤化工装置并发展其下游产品，是贵州当前煤化工发展的方向。