Importance of Low-Temperature Melt-Mixing on the Construction of Stereocomplex Crystallites with Superior Nucleation Efficiency in Asymmetric Poly(l-lactide)/Poly(d-lactide) Blends

The nucleation efficiency (NE) of stereocomplex crystallites (SCs) formed in asymmetric poly(L-lactide)/poly(D-lactide) (PLLA/PDLA) blends is generally unsatisfactory because the competition between stereocomplexation and chain mixing involved in the melt-mixing process can cause low formation efficiency and even severe aggregation of SCs. Herein, it is attempted to achieve high-efficient formation of finely dispersed SCs particles by designing a unique melt-mixing procedure, where the mixing of PLLA with 0.75 wt% PDLA is first performed at elevated temperatures (far above the melting temperature of SCs) to allow the homogeneous mixing of PLLA/PDLA chains and then at a low temperature (slightly above that of homocrystallites) to permit the full stereocomplexation of the premixed chains. It is found that the SCs formed in the blends exhibit unexpectedly low NEs (e.g., 54.5%), much inferior to that (73.6%) in the counterpart without undergoing premixing. This is because the introduction of premixing leads to a remarkable deterioration in the amount of SCs particles formed, despite decreased particle size, highlighting that the direct mixing at low temperatures of 170–180 °C (about 20–30 °C lower than that used in common melt-processing of PLA) is more effective for the construction of SCs with superior NE. The mechanisms for these striking findings are discussed.     

原材料对水泥砂浆性能的影响研究

水泥和砂的质量、引气剂的种类均会对水泥砂浆性能产生影响,其中水泥中高吸附性材料对制备的砂浆工作性能影响较大,需严格加以控制。不同引气剂的起泡、稳泡能力和气泡尺寸不同,对砂浆的稠度、分层度和强度会造成不同影响,采用摇泡试验可快速甑选出合适的引气剂。另外,砂的细度模数,甚至洁净程度（泥灰含量）和堆积密度也会对砂浆性能产生较大影响,在控制水泥的砂浆性能时,应验证并确保重新配制试验用砂的稳定性。     

水质稳定剂HPDP缓蚀阻垢性能评定

用静态阻垢，旋转挂片失得法实验研究了ＨＰＤＰ对ＣａＣＯ３，Ｃａ３（ＰＯ４）２等的阻垢性能以及对Ｑ２３５碳钢的缓蚀性能等。试验证明，ＨＰＤＰ是一种优良的阻垢缓蚀剂，适用于高温，高碱，高ＰＨ，高浓缩倍数的循环冷却水处理，具有广阔的应用前景。     

铸造用有机酯固化剂合成工艺条件及装置选择

分析了铸造用有机酯固化剂醋酸甘油酯和乙二醇醋酸酯合成工艺原理及装置,同时对有机酯合成工艺条件中脱水剂和催化剂的选择的理论依据进行了分析,得出铸造用有机酯固化剂的最佳合成工艺装置和脱水剂、催化剂.     

现代铁水净化技术

铁水的质量是影响铸件产品质量的主要矛盾,其中铁水纯净度是影响铁水质量的薄弱环节。介绍了采用铁神一号净化剂对灰铁、球铁和铸钢进行净化处理的效果、操作方法和注意事项。     

DD—921钢铁常温发黑剂的研制和应用

研究了钢铁常温发黑过程的成膜机理,各组分之间的作用以及相互之间的影响,着重分析了常温发黑的优缺点,工艺控制参数以及经济性。     

航空发动机积炭清洗剂初探

本文简介了积炭的形成过程及其危害，国内外现有去炭工艺水平，重点分析了有机积炭清洗剂各成份的作用和影响，确定了工艺配方，并对其性能和使用情况作了测试。     

CO2固化碱性酚醛树脂的制备及固化机理研究

铸造用CO2固化碱性酚醛树脂是一种新型造型、制芯用粘结剂,它是由羟甲基含量较高的甲阶碱性酚醛树脂和含氧酸盐及碱等物质组成的混合物,甲阶碱性酚醛树脂性能及它们的组成是影响CO2固化碱性酚醛树脂砂强度的主要因素。模仿实际CO2固化酚醛树脂砂的固化过程,利用测定不同条件下碱性酚醛树脂水溶液pH值变化的方法,对CO2固化碱性酚醛树脂与不同交联剂的固化机理进行了探讨,从中得出有关CO2固化碱性酚醛树脂的交联剂和碱的用量范围,并在此基础上,考察它们和表面稳定剂对砂型抗压强度的影响,获得铸造用CO2固化碱性酚醛树脂较佳组成。     

膨润土尾矿作PVC塑料填料的研究

研究了膨润土尾矿的比表面积、添加量及偶联剂表面改性处理对其作为PVC塑料填料时的力学性能和流变性能的影响。结果表明,膨润土尾矿作填料的PVC试样,拉伸强度优于重质CaCO_3,为填料的试样,冲击强度和流动性能则有所下降。钛酸酯作偶联剂有利于提高填充试样的冲击强度。但对拉伸强度无明显效果。膨润土尾矿的添加量约20份时,试样的力学性能最佳。     

Intelligent cooling structure design of "Z-pins like" silicon rods to enhance the ablation resistance of C/C-ZrC-SiC composites above 2500 °C

In order to improve the ablation resistance of C/C-ZrC-SiC composites by reducing the damage of the protective oxide layer, novel "Z-pins like" silicon rods, which were designed and fabricated by liquid phase sintering, were utilised as a dissipative agent. The microstructure evolution and thermal dissipation behaviour were investigated after ablating above 2500 °C for 300 s. After the "Z-pins like" silicon rods were implanted, the anti-ablative property of the C/C-ZrC-SiC composites was drastically improved by the dissipative thermal protection mechanism. The linear ablation rate of the "Z-pins like" silicon rod-reinforced C/C-ZrC-SiC composite was -0.28 μm/s, which is 112.72% lower than the unmodified composite. Additionally, the actual ablative temperature dropped approximately 357 °C, which enabled abundant SiO₂ to remain in the ablation centre. Furthermore, a dense SiO₂-rich oxide layer with a low oxygen diffusion coefficient is formed that covers the entire ablative surface.